Made by devilmaycry
Created 3 days ago
Description
A four-level spice rack for 20 jars, five per shelf, with no back panel to save filament. Each shelf is its own tray with smooth lens-shaped oval sides and a front lip carrying raised spoons and forks. Round connector posts with small pegs join the shelves and pull apart.
Overall size is about 266 × 60 × 325 mm. Print shelves flat and posts upright. Pairs well with a wall strap or a non-slip mat.
Images
A three-tier spice rack that holds 12 jars, four per tier, with each tier stepping up so every label stays in view without lifting a jar out. Each pocket is sized for jars about 40 mm across, so the rack is easy to scan for cumin or anything else. The rack measures 180 mm wide, 150 mm deep and 66 mm tall at the back. Tier heights are 26 mm (front), 46 mm (middle) and 66 mm (back). Each tier is 50 mm deep and 20 mm taller than the one in front. Each jar sits in a 42 mm round pocket, 3 mm deep, which stops it sliding forward. The edges carry a 1 mm chamfer. It prints as one piece, and the three tiers are shown in separate colours so they are easy to tell apart. Remix hooks Step height (20 mm): raise it for taller jars behind, or lower it for a shorter rack. Labels stay readable as long as the step is at least as tall as the label band on the jar in front. Tier depth (50 mm): this is set equal to the back-step. Widening both leaves room for larger jars, and a wider step also gives a clearer view of the row behind. Pocket diameter (42 mm) and depth (3 mm): 2 mm of clearance suits 40 mm jars. Increase the diameter for jars that run a little wide. Deepen the pocket for a firmer hold, or set the depth to 0 for a flat shelf. Jars per tier (4, 44 mm pitch): change the count to alter the rack width. Drop to 3 per tier for a narrower footprint, or add a fourth tier for 16 jars. Pairs well with: a non-slip mat underneath, or a rear lip or wall panel to mount it in a cupboard.

A two-tier spice rack that mounts on the inside of a cabinet door. A flat back plate carries two shelf tiers that project forward, so jars ride on the door rather than on the cabinet shelves and the door can close over them. The upper tier sits 137 mm above the lower shelf, leaving enough height for 105 mm spice jars on the bottom shelf with roughly 14 mm of finger room once a jar is lifted over the 14 mm front lip. Specs Overall size: 175 mm wide, about 174 mm tall, 55 mm deep. Fits an 18 cm print bed. Tiers: two, set 137 mm apart. The top tier ends about 155 mm up the plate. Jar fit: each tier holds jars around 48 mm across. A 14 mm front lip and end walls keep jars in place as the door swings. Door clearance: the tiers project 55 mm from the door. Check the gap between the closed door and the cabinet shelves before printing; hinges and shelf edges can reduce it. Mounting: four countersunk 4.5 mm screw holes through the back plate, with the upper holes at 163 mm up the plate and 12 mm of plate above them. The countersink suits M3.5/#6 flat-head screws; check screw length against the door thickness so they do not break through the front face. Print orientation: back plate down with the shelves growing upward, so no supports are needed. Measure the door-to-shelf clearance and jar diameter before committing to a full print; the depth and tier spacing depend on both.
Distributeur en hauteur pour capsules Nespresso Original (colonnes extérieures) et sucre en morceaux de 30 × 20 mm (colonnes centrales), à coller le long d'une machine. À vérifier avant impression Cavité sucre : 32 × 22 mm, pour des morceaux de 30 × 20 mm. Cavité capsules : 39 mm de large, deux rails de 3 mm, soit 33 mm de passage. Parois latérales du sucre : 2 mm. Largeur totale : environ 152 mm, au-dessus de 140 mm. Incompatibilités Ne convient pas aux capsules Vertuo. Pente de fond uniquement sur les colonnes sucre.

Picking kale, chard or rosemary leaves off the stem by hand is slow, and one hole size never fits both a fat kale rib and a thin rosemary sprig. This herb stripper paddle has seven holes graduated from 12 mm down to 3 mm, so you pick the hole that grips the stem and pull the stem through. The leaves catch on the edge and come off. Each hole has a small flare on the top face so the stem starts in without catching. A hang hole at the end lets the paddle sit on a hook next to the board. Key numbers Paddle: 150 mm long, 40 mm wide, 6 mm thick Stripping holes: 12, 10.5, 9, 7.5, 6, 4.5 and 3 mm, spaced 16.5 mm apart, big to small Hang hole: 10 mm, 12 mm in from the end Corners: 4 mm radius on the flat outline Printing Print flat, with the flared side facing up No supports needed Food-safe filament such as PETG is the usual pick, and a wash by hand is best Use 3 or more perimeters so the thin edges around the holes stay stiff
Brim is a shallow serving bowl with a flat 75 mm base that sweeps up in a smooth curve to a wide, flat rim. The flat base keeps it stable on a table and easy to print without supports on the bottom face. Dimensions Outer rim diameter: 138 mm Rim width: 5 mm, flat and horizontal Opening inside the rim: 128 mm Depth: 30 mm Flat bottom diameter: 75 mm Wall thickness: 2 mm throughout Print notes Print rim-up or base-down; base-down is the natural orientation. The steepening curve near the rim may need supports or slow cooling.
A 2x2 ice lolly mold that makes four pops at once, with a separate stick for each cavity. Each stick flares into a 45 mm round catch disc, so melting juice lands on the disc instead of running down a child's arm and onto the floor. What it's for Making four ice lollies per fill, with a drip guard built into every stick. Summer use with kids, where sticky hands and floors are the main problem. Stacking several molds in a freezer. A lip on top fits a groove underneath. Dimensions Mold body: 110 x 110 mm footprint, 96 mm tall, plus a 2 mm stacking lip on top. Cavities: 90 mm deep, 30 mm across at the mouth, tapering to a rounded tip with an 8 mm radius. Cavity spacing: 48 mm centre to centre in a 2x2 grid. Sticks: 10 mm wide and 3 mm thick, with a 45 mm disc and a raised rim (about 4 mm tall). Disc: dished, with a 41 mm inner recess to hold drips. Print notes Print the mold body upright, with the cavity openings facing up. Print each stick disc-down so the disc lies flat on the bed. Use food-safe filament and a smooth finish if the mold will touch food. Wash it thoroughly before use. Remix ideas Change the tip radius for a blunter or sharper pop. Make the disc larger for extra-messy flavours. Add a name or initial on each disc to tell kids' pops apart. Change the cavity count to a 1x4 or 3x3 layout.