9mm PCD Brushless Motor Stand
Created 2 days ago
Description
A clean, streamlined static test mount for brushless electric drone motors. Elevates the motor to provide ample clearance for 80mm propellers while keeping the mass low and the profile minimal.
Technical Details
- Motor Fitment: Designed for a 9mm pitch-circle diameter (PCD) using four M2 bolts.
- Propeller Clearance: Center height is positioned to comfortably clear an 80mm diameter prop.
- Mounting Setup: Employs a slim 4mm mounting face, eliminating the need for bulky access tunnels. M2 fasteners can pass straight through from the back.
- Base Plate: Features an extended footprint with M5 clearance holes for secure fastening to a test bench.
Photos
Technical views
More like this
Explore more in Automotive, RC & Hobby →
Aero H-Frame Brushless Motor Stand
Bu parça, fırçasız (brushless) drone motorlarının itme gücünü (thrust) güvenle test edebilmeniz için tasarlanmış statik bir tezgah standıdır. Gövdesi itme kuvvetine karşı esnememesi için arka destek takozuyla güçlendirilmiş H profilli bir tabandan oluşur. Modüler Yapı: Motorun takıldığı ön plaka ana gövdeden bağımsızdır. Şu anki plaka 9mm BCD ve 4 adet M2 vida formatına uygun; ileride farklı motorlar için sadece plakayı değiştirerek kullanmaya devam edebilirsiniz. Boyut ve İzinler: Motor ekseni zeminden 90mm yüksekte konumlandırılmıştır. 80mm çapındaki pervaneleriniz tabana çarpmadan rahatça çalışabilir. Sabitleme: Alt kısımdaki ayaklarda tezgahınıza veya ağır bir ahşap bloğa vidalamanız için 4 adet havşalı M4 delik bulunur. Test güvenliği için standı mutlaka zemine sabitleyin.
AeroFit — Micro Motor Mount
A lightweight, minimalist motor mount designed to attach micro brushless motors to a standard 3.0mm carbon fiber boom. It prints flat on the bed with no supports required, making it an extremely quick and clean print. Features Carbon Boom Sleeve: Snug 3.0mm inner diameter with a flex slit, allowing it to clamp securely to standard RC plane tail booms. Motor Interface: 9x9mm hole pattern sized for M2 screws, standard for 11xx series micro motors. Lightweight Build: Thin 1.2mm walls keep weight to an absolute minimum while the conical transition fillet maintains structural rigidity. Print Notes Print upright (motor plate flat on the bed). No supports needed. PLA or PETG recommended for stiffness.
D-Shaft to Hex Motor Adapter
A rigid drive adapter connecting a standard D-shaft motor to a hexagonal RC wheel hub. The base features a keyed socket to prevent slip under torque, while the driven end seats into the tire's existing recess. Overall Length: 25 mm Motor Socket: 6 mm diameter with a 3 mm flat profile, 10 mm depth Wheel Drive: 5.2 mm flat-to-flat hexagonal peg, 10 mm length Base Diameter: 12 mm for structural wall thickness around the socket
Lego piece for wagon door runner with thinner teeth bit slightly smaller
Wagon door runner to replace 3 off 15208 bricks Version with slightly too large slope
0.355 to 0.370 Golf Ferrule
Custom transition ferrule designed to mate golf shafts with an adapting taper. Before printing, verify your shaft tip standard. This part spans from a 0.355-inch taper dimension to a 0.370-inch parallel dimension. Critical Measurements: Inner Bore (Bottom): 9.0 mm (0.355") Inner Bore (Top): 9.4 mm (0.370") Outer Diameter: 13.5 mm (0.530") constant Length: 22.0 mm (0.875") Does not fit standard parallel-only 0.370" shafts at the base without binding.
Custom 16T Mod 0.5 Gear
What it's for A custom 16-tooth spur gear designed for tight tolerances and specific meshing requirements. Built with a modified pressure angle for a sharper tooth profile, and zero standard clearance to strictly match the requested root and outer diameters. Dimensions Outer Diameter: 9.00 mm Root Diameter: 7.00 mm Bore Diameter: 1.55 mm Thickness: 2.00 mm Module: 0.5 (with 28° pressure angle) Print notes Given the small 1.55 mm bore and fine module 0.5 teeth, a resin printer or an FDM machine with a 0.2 mm nozzle and highly calibrated flow is recommended. If printing on standard 0.4 mm FDM, horizontal expansion (XY compensation) may be needed to keep the bore true to size.