Made by a Guest
Created 1 months ago
Remixed once
Description
A custom-fit TPU or rigid shell for the iPhone 13.
This model secures the device by preserving the upper retaining lip around the entire perimeter. The button zones have been converted from open edges into generous side windows—exposing the hardware for clean, tactile presses while maintaining the structural rigidity required for a snap-on fit.
If printing in rigid filament (PLA/PETG), ensure your printer is well-calibrated; a slightly tighter tolerance may snap. TPU is recommended for the best balance of flex and grip.
Images

What it's for A protective case for the iPhone 17 Pro Max in light blue, with a raised rose on the back below the camera cutout. Dimensions Phone body: 163.4 × 78 × 8.75 mm, with 0.3 mm of play per side Walls 4 mm, back 3 mm Rose relief: 1 mm, flat-topped layers Remix ideas Recolour the rose in blue tones to blend with the case Make the rose taller or soften its edges Swap the rose for another motif
A click-in bezel for a 4" LCD touch display mounted in a 97 x 62.2 mm panel window. The 4 mm overall height keeps it low, and a front flange hides the window edge while the screen sits in a pocket behind it. Remix hooks Screen overlap: the visible opening is 93.5 x 60 mm, so it covers 0.5 mm of the 94.5 x 61 mm screen per side. Change the overlap value to show more or less of the screen. Flange: 1.2 mm thick, 105 x 70.2 mm, with a 0.6 mm top chamfer. Widen it to hide a sloppier window cut. Body and clearance: 96.7 x 61.9 mm, 0.15 mm clearance per side. Raise to 0.2 to 0.3 mm for looser printers. Snap barbs: four, 10 mm wide and 0.4 mm proud, tuned for a 2 mm panel. Move them or change their height for other panel thicknesses. Pocket depth: about 2 mm. Deeper pockets need more overall height. Pairs well with a printed rear cover or a spacer plate if the panel is thicker.

An upright charging dock for a wireless earbud case, sized for a desk. The case sits in a 50 × 30 mm pocket, 12 mm deep, on a 60 × 45 × 28 mm base with rounded corners and a flat bottom. A 10 mm notch at the back of the pocket routes a charging cable to the case, and a 4 mm front lip above the pocket floor keeps the case from sliding forward. It replaces a loose case sliding around the desk with a fixed upright position. Fit check Fits: wireless earbud cases with a footprint no larger than 50 × 30 mm and a charging port that faces the rear notch. Does not fit: cases wider than 50 mm or deeper than 30 mm; cases with a bottom-only charging port, because the pocket floor is solid and the notch opens only at the back. Check before printing: measure your earbud case footprint and confirm the 10 mm rear notch lines up with the charging port and plug. Print: one connected piece with a flat bottom and rounded edges, designed for reliable FDM printing on an older printer. No separate pieces or assembly.
Funda rígida diseñada específicamente para las dimensiones del Samsung Galaxy A20e (147,4 × 69,5 × 8,3 mm), incorporando márgenes de tolerancia estructurales para facilitar la inserción del dispositivo. La cara trasera presenta el nombre "Pablo" integrado en relieve volumétrico sólido, utilizando la fuente seleccionada para maximizar la resistencia de las letras. Material recomendado: PLA, PETG o TPU (dependiendo de la flexibilidad deseada). Relieve de texto: 1,5 mm, extruido hacia el exterior. Tolerancias: +0,6 mm en ejes X e Y para un acople por fricción sin forzar la estructura. Perforaciones: Cámara principal dual, lector de huellas dactilares trasero, botonera lateral completa y acceso inferior (USB-C/Audio/Altavoz).
What it's for A solid-walled enclosure for hiding and cooling equipment. Every side wall is closed, and the only airflow path is a sturdy grid cut into the floor, so the box stays dark and quiet from the sides. A 30 × 20 mm cable hole in the lower rear corner lets wiring in and out, and the flat lid lifts off for access. The model prints as separate pieces: the box, the lid and four feet. The lid is a flat plate with a locating lip underneath, slightly larger than the box on every side so it overhangs and can never drop inside. Each foot carries its own coarse threaded stud, so the feet screw directly into matching threaded holes in the floor bosses with no separate fasteners. Dimensions Box: 290 × 200 × 130 mm, with 4 mm walls, solid on all four sides, an 8 mm floor, and a 50 mm solid border around the floor grid. The floor grid is centred on the narrower floor. The thicker floor makes the mesh bars deeper, so airflow per opening drops slightly. Inside fillets: 10 mm radius on the vertical corners and the floor-to-wall edges, stopping 15 mm below the rim. The top 15 mm stays square so the lid and its lip fit without changes. Lid: 294 × 204 mm, 9 mm overall with a 5 mm plate and underside lip; overhangs the box by 2 mm on all sides; 140 mm fan opening and four 3 mm fan screw holes at 124.5 mm center-to-center. Cable hole: 30 × 20 mm in the rear wall, set 20 mm from the left edge and 12 mm above the bottom, inside the solid section so it doesn't weaken the corners. Feet: four solid 24 mm discs, 10 mm tall, each with a 6 mm thick, 8 mm long threaded stud on top; 18 mm overall. The studs use a 1.5 mm pitch. Foot sockets: four corner bosses widened to 14 mm, with threaded holes 6.6 mm across and 11 mm deep at the same 1.5 mm pitch, giving about 0.6 mm clearance on diameter. Print notes Print the box, lid and feet separately. Print the lid lip-side up so its flat face sits on the bed and the lip rises clear of the plate. The floor grid benefits from enough perimeters to keep the bars sturdy. The threads have not been test-fitted; if the feet bind, raise the socket diameter slightly, and if they wobble, lower it. Test-fit the fan and check its screw-hole spacing before committing to a full print. Remix ideas Add a removable filter frame behind the fan opening. Add internal standoffs or a shallow tray for mounting equipment inside. Resize or duplicate the rear cable port for thicker cable bundles. Swap the floor grid for a denser or more open pattern to change the airflow.
Octobay turns a five-bay stack of half-height 5.25" slots into room for eight 3.5" drives, and adds a 25 mm front cage that carries two 92 mm fans. The outer side faces take M3 heat-set inserts, so the whole cage screws into the case's 5.25" rails instead of resting on them. Everything is one printed part: the drive stack, the side mounting blocks and the fan cage print as a single body. Because the fans close off the front, drives now load from the back. The fan cavity behind the grille is hollow, so air still passes through to the drive stack. Dimensions Overall: 145 mm wide × 197.5 mm deep × 205.5 mm tall Fits: five half-height 5.25" bays Holds: eight 3.5" drives, stacked vertically Drive channel: 102.6 mm wide — 1 mm of play around a 101.6 mm drive Mounting 20 insert holes, 10 per side, for M3 heat-set inserts — 4.2 mm across and 6 mm deep Two insert holes per bay, at 41.3 and 117.5 mm from the front, 6.35 mm above each bay floor Solid blocks sit behind each hole to give the inserts something to bite into Three M3 screw holes per side per drive, at 14, 76.6 and 117.6 mm from the front Cross ribs sit clear of the screw holes so a screwdriver can reach every fastener Fan cage Two 92 mm fans, stacked vertically on the 25 mm front section 88 mm fan openings with 4.4 mm screw holes on the standard 82.5 mm square pattern Hollow cavity behind the fans feeds air to the drive channels Print notes Drive channels are open at the back, top and bottom, and the gaps between the inner and outer side walls are open for cable routing. Screw and insert positions and the 205.5 mm height follow common 5.25" bay standards; they have not been checked against a specific case, so measure your bay rails and drives before printing.