AetherAssist — Cyberpunk Watch Prop
Created 1 months ago
Description
A chunky, futuristic wearable casing inspired by dystopian gear. Designed as a solid dummy prop for cosplay or display, it features an angular geometry, heavy chamfers, and an oversized aesthetic.
Features
- Rugged Profile: 46x56mm footprint with a 12mm thickness.
- Strap Lugs: Integrated 24mm strap gaps with 2.5mm pin holes ready for standard watch hardware or paracord.
- Control Array: Features a hex-machined primary dial and a secondary rectangular action button on the right flank.
Print notes
Prints flat on its back. The strap pin holes bridge easily, but verify your printer's overhang limits for the recessed strap gaps.
Images
More like this
Explore more in Keychains & EDC →
Apple Watch SE 44mm Keychain Case
What it's for A two-piece case that turns a 44mm Apple Watch SE (1st gen) into a keychain fob, with no wrist strap. A back shell cradles the watch and carries the key-ring lug. A front bezel fits over it and holds the watch in, leaving the screen open. Dimensions Cavity: 38.6 x 44.6 mm, sized for a 44mm watch body with about 0.3 mm of clearance Outer size: about 44.6 x 50.6 mm, plus the lug Wall thickness: 3 mm Key-ring hole: 5.5 mm Side window on the crown/button edge: 27 mm long, so the Digital Crown and side button stay usable Screen opening: about 1.75 mm of lip around the display Print notes Both parts are laid out separately on the plate. The bezel is flipped so its lip prints flat. Print in PETG or PLA. Check the fit on the stepped joint and sand it if it is tight. The halves are a press fit, and a drop of glue will make the joint permanent. Remix ideas Add a lanyard slot or a carabiner notch. Emboss initials on the back. Make a version for 40mm watches by shrinking the cavity.
Star Apple Watch Keychain Enclosure
A rounded five-point star shell that holds an Apple Watch SE 44 mm (A2352) as a keychain, with the real display open at the front. Two printed parts: a front shell (print mating face down) and a rear cover (flat face down) joined by four M2 screws. Remix hooks Watch fit: case 44 x 38 mm, 0.4 mm clearance per side, cavity depth 11.2 mm, corner radius 8 mm. Change clr, D and cav_r to tune the fit. Display window: 38.4 x 32.8 mm. This is an estimate, so confirm it against the watch. Crown, button, mic and speaker cutouts: positions are placeholders on the right and left sides. Measure the watch and move them before printing. Star size: the star_pts radii (50 / 33 mm) set the roughly 80 mm span. Shrinking the valley radius thins the wall near the cavity corners. Keyring hole: 5 mm at the top point. Raise ringd or move ringpos for a bigger ring. Charging opening: 32 mm round hole in the rear cover (charge_d). Pairs with: M2 x 8 mm screws, a small split ring, or a TPU bumper variant. Still to verify Crown and button height and position Speaker and mic positions Exact display window size Rear sensor bulge depth Treat the first print as a fit prototype. It is not load-rated.
Reach — Telescoping Baton
A compact, print-in-place telescoping baton that expands from a pocketable 8-inch handle into a full 23-inch extension with a flick of the wrist. The segments are designed to print fully assembled with precisely calibrated clearances, locking into place securely upon extension. Dimensions Collapsed Length: 200 mm (approx 8 inches) Extended Length: ~580 mm (approx 23 inches) Handle Diameter: 40.6 mm (1.6 inches) Print Notes Print the main assembly vertically in its default orientation. Do not use supports inside the segments. The included base cap friction-fits into the bottom once printed to retain the segments.
Micro Print-in-Place Joystick
This is a print-in-place ball joint that acts as a miniature thumb joystick. The entire assembly prints as one welded-together block with an internal 0.4 mm gap; once it's off the build plate, a firm snap frees the stick to rotate and swivel in the base. It is designed to be as small as FDM printers can reliably manage without snapping the stalk.
Schlüsselanhänger paula
Schlüsselanhänger mit Namen Paula, bei dem die Schrift nicht flach untergeht: Sie steht 0,5 mm erhaben auf der Platte und lässt sich mit dem Finger ertasten. Das Kettenloch sitzt seitlich, damit der Ring nicht über die Buchstaben schleift. Platte: 30 × 14 × 2 mm, Ecken mit 3 mm abgerundet Schrift: „Paula“ in Lobster, 0,5 mm erhaben Kettenloch: 3,5 mm Durchmesser, linke Seite Druck: flach auf der Platte, ohne Stützen, 0,2 mm Schichthöhe empfohlen
Pion Trivial Pursuit 26 mm, 6 camemberts
Support de pion rond de 26 mm de diamètre avec 6 logements en secteur, accompagné de 6 camemberts (secteurs de 60°) à insérer dans les logements. Les pièces s'impriment séparément, à plat. Support : diamètre 26 mm, hauteur 6 mm, fond 2 mm, logements de 4 mm de profondeur Cloisons entre logements : 1,2 mm Camemberts : 6 pièces, hauteur 3,5 mm, avec un plot de préhension de 1,5 mm Jeu d'insertion : 0,25 mm par côté Matériau conseillé : PLA ou PETG, une couleur par camembert