Angled-Entry Tomato Vine Clips
Created 1 months ago
Description
A set of dual-loop clips designed to secure growing tomato vines to standard 1cm bamboo stakes. The vine loop features a 45-degree angled entry slot, allowing stems to be guided in without threading or bending delicate tips, while the generous internal diameter leaves room for the stem to thicken over the season.
Remix Hooks
- Stake Bore: Currently set to a 10mm inner diameter with a 6.5mm snap gap. Adjust this to match 8mm or 12mm garden stakes.
- Vine Capacity: The vine loop sits at 15mm ID to accommodate mature tomato stems. Scale this up for heavy-set cultivars or down for peppers and beans.
- Entry Angle: The 6mm vine slot is positioned at 45 degrees to prevent accidental slip-outs. Adjust the angle or narrow the gap for vines that need a tighter capture.
- Thickness: Extruded to 8mm, giving the stake loop enough surface area to grip securely when printed in PETG or PLA.
Images
More like this
Explore more in Home & Fixtures →
Ballasted Tomato Planter With Cage
Dwarf tomato plants inevitably turn into top-heavy messes that tip over their cheap nursery pots, and generic wire cages never quite fit the rim. This solves both. A heavy-bottomed, 12-inch tall planter shaped specifically to keep a top-heavy plant grounded. The wide 10-inch base drops into an 8-inch waist before swelling back out to give the root ball room, ending in an 8-inch mouth. The bottom inch detaches as a flush-fit drainage saucer, while the rim features deep, built-in sockets. The included custom cage drops directly into those sockets for a rigid 4-inch scaffold that won't slide sideways in the dirt. Sizing & Assembly Total Volume: ~3.2 gallons. Clearances: 0.5mm slip-fit for the saucer joint, 1mm clearance for the cage legs dropping into the rim. Layout: The pot, saucer, and cage are laid out side-by-side. The pot requires a 300x300mm class Z-axis to print at its intended 12-inch scale.
Botanical Propagation Tray
A shallow, rectangular nursery tray built specifically for sowing seeds and propagating small cuttings. It is elevated on four short feet to allow excess water to escape underneath, preventing root rot. Design Features Drainage Grid: A regular pattern of 3.5mm holes across the bottom ensures proper water flow. Elevated Base: 5mm feet keep the tray off flat surfaces, allowing air circulation and drainage. Sturdy Walls: 2mm thick perimeter walls provide enough rigidity to move the tray when fully loaded with damp soil.
Fenstergriff-Halter Block 110x20x30 mm
Block mit 110 x 20 x 30 mm und zwei Aussparungen an der Unterseite zum Einhaken in Fenstergriffe. Die Aussparungen haben unten gerade Wände und oben eine runde Form (Ø25 mm). Die Öffnung ist mit 21 mm etwas schmaler als der Griff, damit dieser einrastet. Maße: 110 x 20 x 30 mm, Kanten 1,5 mm angefast Aussparungen: Ø25 mm rund oben, 21 mm breite gerade Öffnung unten Mittenabstand: 70 mm Durchgehend durch die 20 mm Breite Material: PLA oder PETG, ohne Stützen druckbar
Tank Tap Bulkhead Fitting 1 1/2" BSP
A through-wall bulkhead fitting in the spirit of a classic water butt tank connector: a broad round flange sits against the tank wall, a long threaded barrel passes through, and a matching lock nut clamps it from the other side. 72 mm flange with a shallow gasket seat for a flat washer or O-ring 1 1/2" BSP-style male thread (47.8 mm major diameter, 11 TPI), 40 mm long 38 mm through bore Separate lock nut, printed alongside Design notes: The thread is a generic approximation of the Whitworth form, so test-fit against your mating part. Cut the tank hole to suit the thread, and use a rubber gasket against the flange. Print the flange face-down; PETG is a sensible choice for water contact.
Halterung mit Gegenstück für Hue-Lampe
Zweiteiliges Set: eine 170 × 45 mm Halterung mit zwei Befestigungslöchern und zwei Steckblöcken sowie ein Gegenstück mit Steckfassungen und einem Klipp-Tunnel für eine quer liegende Hue-Lampe (44 × 36 mm). Beide Teile sind auf Stabilität ausgelegt: dickere Grundplatte, breiter konischer Blockfuß, kräftige Fassungswände und eine dicke Wand über dem Tunnel. Halterung: Platte 8 mm, Blöcke 20 × 20 mm mit konischem Fuß (40 mm unten) Gegenstück: Fassungen mit etwa 6,7 mm Wandstärke, Sockel 70 mm breit Tunnel 44,8 × 36,6 mm, unten offen zum Einklipsen Querbohrungen 5 mm bzw. 5,4 mm Empfehlung: PETG, mindestens 3 Wandlinien, 40 % Infill
DraftBlock — Snap-Fit Vent Cap
A solid plug designed to completely seal an unused round vent or duct. The cover features a flat profile with softly rounded outer edges, hiding the internal void entirely. Features Snap-Fit Mounting: Four downward-facing flexible clips grip the inside of the duct securely. Print-Optimized: The clips are thick enough to provide tension but long enough to flex without snapping in PLA or PETG. Low Profile: Sits just 3 mm proud of the wall or floor line.