Apple Watch SE 44mm Keychain Case
Created today
Description
What it's for
A two-piece case that turns a 44mm Apple Watch SE (1st gen) into a keychain fob, with no wrist strap. A back shell cradles the watch and carries the key-ring lug. A front bezel fits over it and holds the watch in, leaving the screen open.
Dimensions
- Cavity: 38.6 x 44.6 mm, sized for a 44mm watch body with about 0.3 mm of clearance
- Outer size: about 44.6 x 50.6 mm, plus the lug
- Wall thickness: 3 mm
- Key-ring hole: 5.5 mm
- Side window on the crown/button edge: 27 mm long, so the Digital Crown and side button stay usable
- Screen opening: about 1.75 mm of lip around the display
Print notes
- Both parts are laid out separately on the plate. The bezel is flipped so its lip prints flat.
- Print in PETG or PLA. Check the fit on the stepped joint and sand it if it is tight.
- The halves are a press fit, and a drop of glue will make the joint permanent.
Remix ideas
- Add a lanyard slot or a carabiner notch.
- Emboss initials on the back.
- Make a version for 40mm watches by shrinking the cavity.
Images
More like this
Explore more in Keychains & EDC →
Star Apple Watch Keychain Enclosure
A rounded five-point star shell that holds an Apple Watch SE 44 mm (A2352) as a keychain, with the real display open at the front. Two printed parts: a front shell (print mating face down) and a rear cover (flat face down) joined by four M2 screws. Remix hooks Watch fit: case 44 x 38 mm, 0.4 mm clearance per side, cavity depth 11.2 mm, corner radius 8 mm. Change clr, D and cav_r to tune the fit. Display window: 38.4 x 32.8 mm. This is an estimate, so confirm it against the watch. Crown, button, mic and speaker cutouts: positions are placeholders on the right and left sides. Measure the watch and move them before printing. Star size: the star_pts radii (50 / 33 mm) set the roughly 80 mm span. Shrinking the valley radius thins the wall near the cavity corners. Keyring hole: 5 mm at the top point. Raise ringd or move ringpos for a bigger ring. Charging opening: 32 mm round hole in the rear cover (charge_d). Pairs with: M2 x 8 mm screws, a small split ring, or a TPU bumper variant. Still to verify Crown and button height and position Speaker and mic positions Exact display window size Rear sensor bulge depth Treat the first print as a fit prototype. It is not load-rated.
Fluier Cochilie Spiralată
Un fluier cu siluetă de cochilie de mare: camera rotundă poartă o nervură în spirală, iar muștiucul scurt iese în față ca un cioc. Aerul trece printr-un canal îngust, lovește muchia ascuțită din fereastră și face camera să sune. Cameră de rezonanță cilindrică, închisă Inel pentru breloc în spate Nervura spiralată se poate imprima într-o altă culoare Se printează culcat, fără suporturi; stratul de 0,2 mm dă un sunet curat
Minecraft Grass Block Keychain
What it's for A keychain shaped like a Minecraft grass block: smooth brown dirt body, green grass cap that overhangs slightly, and blunt, irregular grass drips on all four sides. A sturdy corner loop takes a key ring. Dimensions Approx. 27 × 27 × 28 mm Cap about 5 mm thick; drips 3.5–8 mm long Loop hole about 4 mm, at one top corner Remix ideas Swap colours for mycelium or snow blocks Change drip layout Enlarge the loop hole for a lanyard
Musqueton porte-clés 25 mm, ouverture 0,2 mm
Musqueton porte-clés d'une seule pièce, de 25 mm de long, avec une fente d'ouverture de 0,2 mm sur le dessus. Dimensions : 25 × 13 × 4 mm Paroi : 2,5 mm Ouverture : 0,2 mm sur le bord supérieur Impression : à plat, sans support Remarque : une fente de 0,2 mm peut se souder à l'impression ; un cutter peut l'ouvrir si besoin
Sleutelhanger Elisabeth, Courgette, 62 mm
Sleutelhanger met de naam "Elisabeth" in Courgette-letters, bedoeld voor een standaard sleutelring. Eén stuk, in één kleur te printen. Voor het printen controleren Breedte van de naam: 62 mm, plus de rand ongeveer 70 mm. Gat in het oogje: 4,5 mm, geschikt voor een gewone sleutelring. Een dikkere ring past niet. Dikte: 2 mm ondergrond, letters 3,2 mm hoog. Past niet bij Karabijnhaken met een dikke ogen of brede band. Het gat is te klein.
60mm Keyring Carabiner Clip
A 60x30mm print-in-place compliant carabiner designed to interface with standard split-ring keychains and lightweight everyday carry items. The frame features a 5mm constant cross-section with alternating triangular truss cuts along the spine to reduce material weight without compromising the hinge action. Fitment and Tolerances Clearance: The interlocking latch mechanism relies on a 0.4mm printed gap. Ensure flow rate and horizontal expansion are calibrated to prevent the gate from fusing to the catch. Hardware: Accepts standard flat or wire keyrings up to 4mm in thickness through the inner loop. Incompatibilities: This is a decorative thermoplastic clip for keys and pocket tools. It is strictly non-load-bearing. Do not use for climbing, rigging, securing heavy equipment, or any life-safety applications.