Arcane Tracery Bracer
Created 3 months ago
Description
A 180mm rigid forearm cuff designed around a continuous, self-supporting gothic tracery pattern. The interlocking pointed arches and diagonal cross-cuts mimic the organic load-paths of topology optimization while keeping a distinctly high-fantasy arcane aesthetic. It features a 70-degree slip gap at the back, thick structural armor bands, and rounded comfort edges.
Remix hooks
- Dimensions: Currently scaled for an average arm (35mm inner radius at the wrist, 48mm inner radius near the elbow). To resize it for a different wearer, adjust the
wrist_randforearm_rbase variables. - Flexibility: The 4mm wall thickness makes this a rigid piece. If you want it to flex open over the wrist rather than sliding on, drop
wall_thicknessto 2mm and print in PETG. - Tracery density: The lattice overlaps heavily to create the branching web. Scaling the
widthandheightof thepointed_cutcalls will tighten or open up the negative space. - Supportless: The vesica piscis (pointed arch) cutouts are radially oriented and all internal angles exceed 45 degrees, meaning this prints straight up from the wrist with zero supports.
Photos
Technical views
More like this
Explore more in Decor & Display →
Pebbl — Aquarium Plant Weight
Pebbl is a small slotted disc that holds aquarium plant stems down in the substrate. The stem slides in through the open slot and seats in a rounded pocket at the centre, so the plant stays put without wire, glue or clips. The flat, compact profile sits low and is easy to bury under gravel or sand. Dimensions Diameter: 25 mm Thickness: 8 mm Slot width: 3 mm, running from one edge to the centre Edges: 1 mm chamfer on the top and bottom rims Slot end: rounded at the centre so a stem seats cleanly Print notes Prints flat on the build plate with no supports. PETG at high infill is a good choice for sinking weight. Plastic is light, so larger plants may need a thicker or wider disc. Use an aquarium-safe filament.
Wall-Mounted Running Medal Holder
What it's for A wall-mounted rack for displaying running medals. Each ribbon slides onto one of eleven angled prongs that project from a flat backboard, so medals hang in a neat row and stay visible instead of ending up in a drawer. The prongs tilt up and finish in a ball tip, which holds the strap in place once it is looped on. The backboard is left plain above the prongs, giving the row of medals a clean edge to hang against and keeping the silhouette simple to print. The front face is completely smooth — the hanging slots are cut only into the back, so no holes or screw heads show through the display side. Dimensions Backboard: 300 mm wide × 60 mm tall × 10 mm deep Medal prongs: 11 prongs at 25 mm spacing, each reaching 30 mm out from the backboard at a 15° upward tilt, with ball tips Hanging slots: two keyhole pockets cut 6 mm into the back, 200 mm apart, leaving 4 mm of solid material at the front Prong spacing is the number worth checking against your own medals — wide straps need more room between prongs, and the spacing can be opened up if yours run thick. Roughly 10 to 15 medals fit across the 300 mm board. Print notes Prints as one piece; no assembly required. Lay the backboard flat on the plate so the prongs build up in front of it. The tilt keeps them self-supporting, so no supports are needed. Because the slots are stopped short of the front, the screw heads sit recessed in the back rather than passing through the board. Two wall screws 200 mm apart carry the holder. Remix ideas Widen the backboard to 400 or 500 mm and add prongs for a larger collection. Add a second row of prongs below the first to stagger medals in two tiers. Add a raised name plate or a finish-line banner along the plain top edge using the same prong layout. Materials Rigid filament is the better choice here; the prongs carry real weight and a soft or flexible material will let them droop.
Flat-Pack OO Scale Corrugated Garage
A flat-pack OO scale garage with corrugated iron panels, a gable roof and sliding timber doors. Every piece prints flat on the bed with no supports, then assembles with glue. The side walls carry tabs that pass through slots in the front and back gable ends, with 0.3 mm clearance. The two roof panels sit on the gable slopes. Two plank-and-brace doors hang from a separate rail across the front opening. Footprint: about 48 × 80 mm, ridge height about 48 mm Pieces: 2 side walls, 2 gable ends (front one has the door opening), 2 roof panels, 2 doors, 1 rail Panel thickness 1.6 mm with raised corrugation ribs Print flat, glue the joints, fix the rail above the opening
Gothic Rose Window Cathedral Shelf
A cathedral-front wall shelf in two glue-together halves, with blind lancet windows, pinnacles, battlements and a blind arcade below the shelf. Each half now carries layered rose windows in the style of a medieval cathedral facade: stepped rings, twelve radiating spokes, cusped lobes and a domed centre boss. Design notes Large rose window at the top centre of each half, plus two more in the lower arcade Countersunk screw holes for hanging, with clear access pockets Tongue-and-groove seam for super gluing the halves together Each half fits a 250 mm-class print bed
Flat Snake Assembly Kit
What it's for A flat, solid snake that prints as separate pieces and snaps together by hand: head, two body segments, tail, two eyes and three connector pins. Edges are rounded, there is no surface detail, and nothing needs supports. Dimensions Thickness: 4 mm Pin holes: 3.5 mm diameter Pins: 3 mm diameter, 4 mm long Joints: half-thickness lap joints, so the pin passes vertically through both overlapping ends Eyes: 6.5 mm domed discs with a 3 mm peg that fits holes in the head Remix ideas Lengthen the snake with more body segments. Change the wave amplitude for a tighter or straighter snake. Add a keyring hole in the tail.
55كعبة مجزءة
Exploded miniature of a masjid scene with every component spread apart with visible gaps. Parts: white base, platform tiers, four black Kaaba walls, roof, door, gold bands, walkway tiles, arrows, palms, bushes, grass, pilgrims, Zamzam station, Maqam Ibrahim and blue sign parts. Layout: exploded only, no assembled copy. Export: the download is one file; separating individual parts happens outside this model.