SUPPORT PRINTYTRON
New Model
Loading 3D preview…

Aufsteck-Schraubklemme mit Haken

Made by LintelCivet

Created 3 months ago

Storage & Organizationu-clamphooksquare-tubem10-threadstorageno-supports
Remix this model →

Description

Eine umstrukturierte Klemmhalterung, die sich als offenes U-Profil direkt über ein 15 x 15 mm Vierkantrohr stecken lässt. Die Fixierung erfolgt durch eine gedruckte M10-Druckschraube auf der Rückseite, die das Rohr fest gegen die Vorderwand presst. Auf der Frontseite sitzt ein massiver Haken.

Anpassungsmöglichkeiten für Remixes

Dieses Modell ist so ausgelegt, dass die grundlegenden Klemm-Mechanismen leicht für andere Einsatzzwecke skaliert werden können:

  • Stangenmaß: Der innere Ausschnitt hat aktuell 15,6 mm Breite für etwas Spiel auf 15 mm Stangen. Wer größere Rohre nutzt, kann den Hauptkörper entsprechend verbreitern.
  • Haken-Geometrie: Der Ausleger ragt 12 mm nach vorne, die Spitze zieht 16 mm nach oben. Das lässt sich gut durch flache Halterungen oder Ösen ersetzen.
  • Gewinde: Das M10x2 Gewinde hat im Gehäuse 10,6 mm Durchmesser (intern). Für mehr Klemmkraft auf glatten Metallrohren kann die Schraube gegen eine Standard-Metallschraube mit Gummipad getauscht werden.

Images

SUPPORT PRINTYTRON
Tip Jar
Printytron built this for free. If it saved you a trip to the shop, a tip helps keep it free.
Need filament at a great price?
Printing this one? Stock up through our eSun partner link — your price stays the same, but Printytron gets a small commission to go towards our costs.
Two-Piece Sliding Storage Drawer with Spring Release

Two-Piece Sliding Storage Drawer with Spring Release

A minimalist two-piece sliding storage drawer: a ribbed outer housing with an open front and a separate inner drawer with a flush, handle-free face. The housing measures 100 × 150 × 60 mm with 10 mm rounded outer corners and 1.6 mm walls. Vertical ribbing stiffens the side walls, and thin 45° guide rails keep the drawer aligned. The guide rails and side stop tabs stay inside the outer walls, with only the ribs standing proud by design; the front ends of the rails stop inside the rounded front corners. The top is an open frame with a 12 mm solid rim, thickened to 3.4 mm so the stacking recess does not cut through. The drawer slides on the rails and locks closed with rounded snap bumps that seat into grooves in the housing. Push the drawer inward to release the bumps; the rear U-shaped leaf spring then pushes it forward. The spring is 0.95 mm thick and 40 mm wide, anchored to the inner back wall and touching the floor only where it meets that wall. A 45° chamfer under its bottom edge lifts the loop clear of the floor as it runs forward, so it flexes freely and still prints without supports — the trade-off is a shorter front loop, so the spring is on the soft side. A 45° finger bevel under the bottom front edge gives a hidden pull once the drawer has popped out. Flexible side stop tabs catch pockets near the back of the drawer, limiting travel to about 95 mm; press the tabs aside to remove the drawer fully. The stop pockets are 1.2 mm deep with 1.4 mm of solid wall behind them. The housing also stacks: a 1.5 mm bottom foot, inset 2.2 mm with a 45° chamfer, sits in a matching 1.8 mm recessed step on the top rim with 0.3 mm clearance. Housing: 100 × 150 × 60 mm, ribbed sides, open top with 12 mm rim, 10 mm rounded corners, 1.6 mm walls Drawer: 95.7 × 135 × 53.2 mm, flush front, no handle, side snap bumps Release: push-push detent with rear U-spring Pull: hidden 45° finger bevel under the front bottom edge Stop: flexible side tabs limit travel to about 95 mm; press aside for full removal Stacking: 1.5 mm bottom foot and matching 1.8 mm top recess Printing: two separate pieces, no supports, overhangs 45° or shallower Tuning: spring force and detent interference may need adjustment after a test print

HumbleMongoose · 5 days agoRemix →