Made by RotorLoupe
Created yesterday
Description
flare tubintake for stove
Images

Open-top storage box with three equal compartments side by side, and the name CHARO raised across the full front face. Outer size: 210 x 112 x 85 mm Walls and dividers: 3 mm Floor: 4 mm Compartments: 3, each about 66 x 106 mm inside Lettering: Bebas Neue, about 200 x 77 mm, raised 1 mm on the front Prints upright with no supports
What it's for A plain open-topped square box with a closed floor, sized to hold small parts, tools, or loose odds and ends on a desk or workbench. The straight sides and flat base keep it stable on the print plate and easy to drop things into from above. Dimensions Outer footprint: 75 × 75 mm Height: 25 mm Wall thickness: 3 mm Floor thickness: 3 mm Top: fully open, no lid Print notes Prints upright as it sits, with no supports needed for the vertical walls. A 3 mm wall and floor hold up well in PLA or PETG at a standard layer height; thicker walls take a slightly wider nozzle or more perimeters comfortably. Remix ideas Add a lid or a stacking lip so several boxes can sit on top of one another. Round the outer corners for a softer look and less sharp handling. Divide the interior with a grid to sort small hardware.
PivotTee è un portabrugole piatto per chiavi a T da 10 a 3 mm, con perni laterali che lo fanno ruotare da orizzontale a verticale su una base da fissare al cassetto. Un fermo girevole dietro il blocco lo tiene in verticale durante l'uso, e il perno centrale accoglie un inserto filettato M3 per avvitare il fermo. Caratteristiche Otto sedi da 10 a 3 mm con fessura superiore e numeri incisi Base con due fori svasati da 5 mm Perno del fermo da 8 mm con foro da 4,2 mm per inserto M3 (profondità circa 8 mm) Fermo girevole 44 × 14 × 6 mm Print notes Tre pezzi stampati sdraiati, senza supporti Inserto filettato da scaldare a caldo nel foro del perno
A reusable ice brick for lining the floor of a cooler. The block is hollow, measures 120 x 80 x 25 mm, and has flat, square sides so four bricks sit shoulder to shoulder across a standard cooler base without the gaps that store-bought ice packs leave. A threaded fill port in the top face lets you refill the block with water. A separate slotted screw plug closes the port. Its head sits in a recess, so the top surface stays flat. The plug prints beside the block and needs a coin or screwdriver to turn. Outer size: 120 x 80 x 25 mm Wall thickness: 2.4 mm Flat mating faces on all four sides Threaded fill port with a flush slotted plug (2 pieces) Not test-printed or pressure-tested for sealing For a watertight result, print in PETG with extra perimeters and add PTFE tape or a thin gasket under the plug head. Fill to about 90% so the water has room to expand as it freezes.
A set of eight small label plates with raised white lettering, each 1 in × 0.5 in. Blue plates read ROAD, CURB, REAR, REAR; red plates read SCENE, DECK, TANK, TANK. Intended for marking bins, shelves, hooks or parking spots. Specs Plate: 25.4 × 12.7 mm, 2 mm thick, rounded corners, no mounting hole Lettering: 0.8 mm raised, thickened strokes, centred on each plate Layout: two columns (blue left, red right), 18 mm row spacing Print: flat on the bed, no supports; filament swap at letter height for two-tone Mounting: double-sided tape or adhesive
Loose items slide around in a drawer, and a floorless box with a divider keeps them in place. This one is a rectangular frame with no floor and a full-height wall across the middle. Key numbers Outer size: 184 x 93.33 x 115 mm (height) Wall thickness: 2.4 mm Divider: 2.4 mm, full height, at the middle of the 184 mm length Three boxes side by side fill a 280 mm drawer depth Print: open end up, no supports needed, fits beds of 210 mm or larger