Made by Ollie
Created yesterday
Description
A print-in-place flexi Christmas tree with a separate snap-fit stump and a separate snap-fit star. There is no host device, thread standard or model number to match here: the fit that decides whether it works is the hidden hinge clearance, then the plug-and-slot snap joints that hold the stump and the star.
The tree is eight stacked tiers, each a tent shape rising to a centre ridge, cut with jagged, uneven fir-style boughs that swing out past the body, droop at the tips and step back in toward the top. The bottom tier rises 17 mm and each tier above is 1.2 mm lower. The topmost tier carries a slot with two snap dimples for the star; the slot is 8 mm deep, and the star’s plug is 14 mm long. The stump and the star both sit beside the tree on the plate as their own pieces.
What it fits and replaces
Check before printing
What it is not
Specs as it sits on the plate
Images
Tasse à chocolat creuse de 100 mm de haut, avec un père Noël cramponné à la paroi arrière, en position d'escalade, et une anse imprimée à part. La tasse est ouverte en haut, sans couvercle, avec une base plate et une paroi lisse côté +X puisqu'elle n'a plus d'anse. Le père Noël est solidaire de la tasse, plaqué contre la face extérieure : ses bras montent jusqu'au rebord et ses deux moufles blanches, rondes, se logent dans deux creux ronds du rebord, à environ 14 mm de chaque côté du centre ; sa tête et son bonnet dépassent au-dessus du rebord, et ses jambes prennent appui contre la paroi, à l'extérieur, les pieds à quelques millimètres au-dessus du plateau. Chaque partie est découpée suivant la forme de l'intérieur, y compris au-dessus du rebord : rien ne dépasse dans la cavité, qui reste creuse sur toute sa hauteur. La face avant porte des creux à la forme exacte des décorations de Noël, qui s'impriment à plat sur le plateau et se collent dedans. Tasse : 100 mm de haut, 80 mm de diamètre en bas, 110 mm en haut, parois de 3 mm, fond de 5 mm, rebord arrondi, intérieur entièrement creux et dégagé, base plate ; largeur totale d'environ 130 mm avec l'anse en place Père Noël intégré : derrière la tasse, face à l'avant, en position d'escalade ; remonté pour que la tête et le bonnet passent au-dessus du rebord ; moufles rondes logées dans les creux du rebord, jambes et pieds contre la paroi extérieure, les pieds à environ 6 mm au-dessus du plateau ; manteau et bonnet rouges, fourrure, barbe et moufles blanches, ceinture et bottes noires, visage et yeux ; les couleurs se touchent sans se chevaucher, à exporter en 3MF pour les conserver Moufles et creux du rebord : moufles maintenues rondes, décalées d'environ 3 mm vers l'extérieur du rebord pour ne plus être rognées par la cavité, avec les manches qui suivent ce décalage ; deux creux ronds au rayon des moufles, avec 0,4 mm de jeu pour la colle, à environ 14 mm de chaque côté du centre ; ils ne traversent pas la paroi et l'intérieur reste lisse ; peu profonds, le rebord ne faisant que 3 mm d'épaisseur Anse séparée : posée à plat à droite de la tasse, côté +X, même couleur chocolat ; rayon de 22 mm, épaisseur de 10 mm ; extrémités découpées pour épouser la paroi ; se colle sur la tasse, sans creux de guidage ; s'imprime sans support sur sa face large Décorations séparées : sapin à trois étages et tronc sans étoile au sommet, deux étoiles latérales et quatre flocons, tous verts, 1,4 mm d'épaisseur, posés à plat devant la tasse côté −Y ; les deux flocons latéraux sont à environ 26 mm du centre et 42 mm de haut Creux d'encastrement des décors : profondeur d'environ 1,5 mm, 0,3 mm de jeu tout autour pour la colle ; la paroi garde environ 1,5 mm sous les creux et l'intérieur reste creux Points d'impression : prévu pour une FDM domestique ; les jambes du père Noël sont en porte-à-faux contre la paroi inclinée et ses pieds ne reposent pas sur le plateau, un peu de support peut être utile à cet endroit ; les branches des flocons font environ 2,4 mm de large, ce qui est fin pour une buse de 0,4 mm ; un flocon plat sur une paroi courbe reste une approximation La tasse sert de contenant pour des bonbons ou du chocolat chaud. L'anse et les décorations vertes s'impriment à part, chacune dans sa couleur, puis se collent : l'anse sur le côté de la tasse, les décorations dans leurs creux sur la face avant.
Evergreen Ring reduces the Christmas ornament to a clean silhouette: an open circular ring with a hanging loop, a pair of small three-tier trees tucked into the lower-right corner, and a large six-armed snowflake filling the top-left, its outer arms running into the ring and clipped by it. The right-hand tree sits fully inside the hoop, its tiers clear of the ring, with only its trunk running down into the bottom of the ring. The companion tree to the left is about 1.5 mm larger, with roughly 1 mm separating the pair, so the motif reads as a deliberate little grove rather than a repeat. The snowflake is centred about 12 mm in from the corner, and the arms that meet the ring are what hold it in place. Ring, trees and snowflake all stand the same 3 mm tall, giving the piece a single even plane that sits flat against a branch, a window or a gift tag. Every element is joined to the hoop, so the whole ornament prints as one solid piece with no assembly and no loose parts. Dimensions Ring: 60 mm across, 66 mm tall overall including the hanging loop, 3 mm thick Trees: two small trees occupying roughly 23.4 × 15.6 mm combined, 3 mm thick Snowflake: about 32.8 × 34 mm, 3 mm thick Features Open-ring ornament with an integrated hanging loop Two small three-tier trees side by side in the lower-right corner, with the tiers fully clear of the ring One tree about 1.5 mm larger than the other Large branched snowflake in the top-left corner, its outer arms cut off by the ring and fused to it Only the tree trunks and the snowflake's outer arms meet the ring, keeping the scene connected Uniform 3 mm thickness across every part Prints as a single piece, no supports needed Print notes Lay the ornament flat on the plate; the even thickness means no tall overhangs Any filament works — use contrasting colours for the trees and snowflake if you print in multiple colours
What it's for A flat, two-dimensional Christmas tree cutout with six stacked, tapering tiers over a short trunk. The tip is a plain point — no star, no topper — and the silhouette stays clean and unbroken. Seven small stars and seven small circles are scattered across the tiers as through-holes in those same shapes, punching light through the flat body and adding detail without any surface relief. It prints as one flat piece and comes off the plate ready to use, with no assembly and no supports. Dimensions Overall footprint: 70 mm wide × 98 mm tall Thickness: a constant 4 mm Tiers: six stacked branches Star holes: 7 through-holes, roughly 2.6 mm across the points Circle holes: 7 through-holes, 3.6 mm across Top: plain pointed tip, no star All of the star and circle holes sit inside the tree's outline, including the ones near the tip, so nothing breaks the outer silhouette. Print notes Print flat on the plate. The constant 4 mm body means there are no overhangs and no supports are needed. The holes are small, so a 0.4 mm nozzle prints them cleanly; the star points are sharp and may round off slightly. The flat faces are a good place for a colour change or a two-tone filament swap. Remix ideas Scale the outline up or down for a larger wall piece or a small tag. Thin the body to 2–3 mm for a lighter decoration, or thicken it for a freestanding table piece. Enlarge the star and circle holes for a stronger see-through effect, or change their count for a denser or sparser look. Add a name across the trunk, or add a hanging hole if you want to suspend it.
A small snowflake pin with six branched arms, made to be worn on a shirt. Two loops on the back take a standard safety pin, so the snowflake sits on the fabric like a brooch. Six-arm snowflake with side branches and rounded tips Two back loops, 8 mm apart, for threading a safety pin Flat front face prints directly on the plate No supports needed Roughly 31 mm across and under 6 mm thick
A hollow Christmas bauble with a six-armed snowflake cut through the front and back. The snowflake branches are set at a 40° angle so no island of shell is trapped between them; the cutout stays one connected shape. Rings of small round through-holes sit above and below the middle, and the equator is left plain. Raised bands run above and below the equator, and a cap with a hanging loop sits at the top. The bottom is flattened into a small footing so the ornament can stand upright on the print plate; the curved lower sides generally need supports. Specs Overall size on the print plate: 59.9 mm wide × 59.7 mm deep × 71.5 mm high Ball diameter: 60 mm Wall thickness: 2.5 mm, hollow shell Bottom footing: about 19 mm across Cutouts: one six-armed snowflake through the front and one through the back, about 22 mm across with fine branches around 1.8 mm thick Snowflake branches: 40° branch angle, arranged so no detached wall islands are left inside the cutouts Dot holes: 12 above the middle and 12 below, each a 3.2 mm hole straight through the wall; no hole row at the equator Bands: raised rings above and below the equator Top: cap with hanging loop Printing: single piece; supports needed on the curved sides Use: Christmas tree ornament or hanging decoration; the flattened base also lets it stand on a flat surface
A cigarette you can't smoke but can play: an 84 mm-long fipple whistle disguised as a filter-tipped stick, complete with an orange ember tip, a white paper body and a tan filter. Inhale through the filter end and air slips through the intake hole near the ember, runs a thin flat duct across a window and breaks over a sharpened edge — the classic whistle mechanism, wearing a noir prop's silhouette. It is an inhale-only instrument; blowing back out through it will sound weak or not at all. This version is tuned for a softer, lower note: the duct is narrow and shallow, the window is long with a gentle ramp, and the intake is widened a touch to keep the hiss down. A gentle, steady inhale gives the smoothest sound; a hard pull turns breathy. Design notes Three colour-coded sections in the viewer: Ember Tip, Paper Body and Filter, printed as a single piece. The underside is flattened, so it sits stable on the plate and needs no supports. Keep your lips clear of the intake hole while you inhale — that hole is the voice. Tone stays tunable: a longer window takes it darker, a slightly more open duct brings back volume if it comes out too faint. Pairs well with a trench coat, a rainy window, and anyone who appreciates a joke that also functions.