Evergreen Ring — Open Christmas Tree Ornament
Created yesterday
Description
Evergreen Ring reduces the Christmas ornament to a clean silhouette: an open circular ring with a hanging loop, a pair of small three-tier trees tucked into the lower-right corner, and a large six-armed snowflake filling the top-left, its outer arms running into the ring and clipped by it. The right-hand tree sits fully inside the hoop, its tiers clear of the ring, with only its trunk running down into the bottom of the ring. The companion tree to the left is about 1.5 mm larger, with roughly 1 mm separating the pair, so the motif reads as a deliberate little grove rather than a repeat. The snowflake is centred about 12 mm in from the corner, and the arms that meet the ring are what hold it in place. Ring, trees and snowflake all stand the same 3 mm tall, giving the piece a single even plane that sits flat against a branch, a window or a gift tag.
Every element is joined to the hoop, so the whole ornament prints as one solid piece with no assembly and no loose parts.
Dimensions
- Ring: 60 mm across, 66 mm tall overall including the hanging loop, 3 mm thick
- Trees: two small trees occupying roughly 23.4 × 15.6 mm combined, 3 mm thick
- Snowflake: about 32.8 × 34 mm, 3 mm thick
Features
- Open-ring ornament with an integrated hanging loop
- Two small three-tier trees side by side in the lower-right corner, with the tiers fully clear of the ring
- One tree about 1.5 mm larger than the other
- Large branched snowflake in the top-left corner, its outer arms cut off by the ring and fused to it
- Only the tree trunks and the snowflake's outer arms meet the ring, keeping the scene connected
- Uniform 3 mm thickness across every part
- Prints as a single piece, no supports needed
Print notes
- Lay the ornament flat on the plate; the even thickness means no tall overhangs
- Any filament works — use contrasting colours for the trees and snowflake if you print in multiple colours
Images
More like this
Explore more in Gifts, Seasonal & Personalized →
Flat Six-Tier Christmas Tree Cutout
What it's for A flat, two-dimensional Christmas tree cutout with six stacked, tapering tiers over a short trunk. The tip is a plain point — no star, no topper — and the silhouette stays clean and unbroken. Seven small stars and seven small circles are scattered across the tiers as through-holes in those same shapes, punching light through the flat body and adding detail without any surface relief. It prints as one flat piece and comes off the plate ready to use, with no assembly and no supports. Dimensions Overall footprint: 70 mm wide × 98 mm tall Thickness: a constant 4 mm Tiers: six stacked branches Star holes: 7 through-holes, roughly 2.6 mm across the points Circle holes: 7 through-holes, 3.6 mm across Top: plain pointed tip, no star All of the star and circle holes sit inside the tree's outline, including the ones near the tip, so nothing breaks the outer silhouette. Print notes Print flat on the plate. The constant 4 mm body means there are no overhangs and no supports are needed. The holes are small, so a 0.4 mm nozzle prints them cleanly; the star points are sharp and may round off slightly. The flat faces are a good place for a colour change or a two-tone filament swap. Remix ideas Scale the outline up or down for a larger wall piece or a small tag. Thin the body to 2–3 mm for a lighter decoration, or thicken it for a freestanding table piece. Enlarge the star and circle holes for a stronger see-through effect, or change their count for a denser or sparser look. Add a name across the trunk, or add a hanging hole if you want to suspend it.
Festive Headstand: Upside-Down Pineapple with Ball Gag
A cartoon pineapple does a festive headstand: it balances on an oversized leafy crown, the fruit body rising above, and a big fluffy red Christmas hat droops off to one side, ending in a single large rounded bobble. Two wide-open eyes with dark pupils and brows sit on the fruit, a small skin-toned nose between them, and a black ball gag framed by small red puckered kissing lips takes the place of a mouth. The lips form a compact ring with cupid's-bow lobes on top and a fuller lower lip, set back into the fruit's surface around the ball so the black shows through the middle. The strap runs around the head and across the front, outside the lips, lying against them as it passes over their corners and into the ball, so the lips sit behind it. The leaves are the star of the stand: a dozen broad blades plus a ring of shorter ones fan out beneath the fruit and lift it clear of the surface, giving the upside-down pose its height and silhouette. The body is scaled in staggered rows of triangular scales, kept clear of the face, so the fruit reads as a pineapple from any angle. And yes — the inverted pineapple is the classic swinger sign, worn here in full holiday dress. Use it as intended, or simply as a seasonal oddity. Made to hang A loop sits upright on the hat's peak, ready for a hook, ribbon or tree branch. With no base disc under the crown, the pineapple rests on its leaf tips — perfect for hanging, less so for standing on a shelf. The hat's tip droops to one side and ends in one large rounded bobble, so check clearance around the hook. Design notes Tall, wide leaf crown with 12 broad leaves and a ring of shorter ones; it doubles as the stand. Face: two open eyes with pupils and brows, a small nose, a black ball gag, and small red puckered kissing lips with a cupid's bow. The lips are sunk back into the face around the ball rather than standing proud of it, so the strap sits in front and the red shows as a ring. Strap wraps the back of the head and bands across the front outside the lips, resting against the face and covering their corners. Staggered triangular scales wrap the body in rows, with the face left smooth. Oversized hat with a thick trim of rounded puffs and a smooth bobble, finished with the hanging loop. The fluffy hat trim is the widest point, so check your bed size before printing.
4 mm Hanging Hole Snowflake Christmas Ornament
A flat, six-armed snowflake ornament with a 4 mm string hole through a round eyelet that sits on the tip of the top arm. It prints as one solid piece, 3 mm thick, flat on the bed with nothing to support. Fits String, twine or thin ribbon up to roughly 4 mm through the eyelet; a knot or bead wider than the hole keeps it from pulling through. A tree branch, hook or nail with about 71 mm of clear height, so the eyelet and the point below it hang free. Does not fit / not included No hook, clip, stand or separate hanger — the eyelet is part of the print itself. No text, logo or engraved date; nothing is lettered on it. Not a multi-part kit; there is nothing to assemble. Check before printing Overall footprint is 55.3 mm wide across the flat sides and 70.5 mm tall including the eyelet, at 3 mm thick. Confirm the hanging spot leaves that much room and that your cord end passes the 4 mm hole — a hole that prints slightly tight may need a quick ream with a 4 mm drill bit. What is on the part Six broad arms, 4.5 mm wide with rounded ends, joined by side branches 4 mm wide — thick enough to handle and pack away each year. A 14 mm hexagon at the centre with a 6 mm hole through it, which trims filament without thinning the arms. An 11 mm rounded eyelet overlapping the full width of the top arm, so it reads as an extension of the arm rather than something stuck on. Every arm and branch is solid and properly joined, so the whole ornament stays low on filament while holding up to a season of hanging.
Hollow 60 mm Star-Cutout Christmas Bauble
A hollow Christmas bauble with a star cut through the front and back and rings of small round holes above and below the middle. Raised bands run above and below the equator, and a cap with a hanging loop sits at the top. The bottom is flattened into a small footing so the ornament can stand upright on the print plate; the curved lower sides generally need supports. Specs Overall size on the print plate: 59.9 mm wide × 59.2 mm deep × 71.5 mm high Ball diameter: 60 mm Wall thickness: 2.5 mm, hollow shell Bottom footing: about 19 mm across Cutouts: one star through the front and one through the back Dot holes: 12 above the middle and 12 below, each a 3.2 mm hole straight through the wall; the equator is left plain with no ring or hole row Bands: raised rings above and below the equator Top: cap with hanging loop Printing: single piece; supports needed on the curved sides Use: Christmas tree ornament or hanging decoration; the flattened base also lets it stand on a flat surface
Tasse chocolat 100 mm, père Noël et anse séparée
Tasse à chocolat creuse de 100 mm de haut, avec un père Noël cramponné à la paroi arrière, en position d'escalade, et une anse imprimée à part. La tasse est ouverte en haut, sans couvercle, avec une base plate et une paroi lisse côté +X puisqu'elle n'a plus d'anse. Le père Noël est solidaire de la tasse, plaqué contre la face extérieure : ses bras montent jusqu'au rebord et ses deux moufles blanches, rondes, se logent dans deux creux ronds du rebord, à environ 14 mm de chaque côté du centre ; sa tête et son bonnet dépassent au-dessus du rebord, et ses jambes prennent appui contre la paroi, à l'extérieur, les pieds à quelques millimètres au-dessus du plateau. Chaque partie est découpée suivant la forme de l'intérieur, y compris au-dessus du rebord : rien ne dépasse dans la cavité, qui reste creuse sur toute sa hauteur. La face avant porte des creux à la forme exacte des décorations de Noël, qui s'impriment à plat sur le plateau et se collent dedans. Tasse : 100 mm de haut, 80 mm de diamètre en bas, 110 mm en haut, parois de 3 mm, fond de 5 mm, rebord arrondi, intérieur entièrement creux et dégagé, base plate ; largeur totale d'environ 130 mm avec l'anse en place Père Noël intégré : derrière la tasse, face à l'avant, en position d'escalade ; remonté pour que la tête et le bonnet passent au-dessus du rebord ; moufles rondes logées dans les creux du rebord, jambes et pieds contre la paroi extérieure, les pieds à environ 6 mm au-dessus du plateau ; manteau et bonnet rouges, fourrure, barbe et moufles blanches, ceinture et bottes noires, visage et yeux ; les couleurs se touchent sans se chevaucher, à exporter en 3MF pour les conserver Moufles et creux du rebord : moufles maintenues rondes, décalées d'environ 3 mm vers l'extérieur du rebord pour ne plus être rognées par la cavité, avec les manches qui suivent ce décalage ; deux creux ronds au rayon des moufles, avec 0,4 mm de jeu pour la colle, à environ 14 mm de chaque côté du centre ; ils ne traversent pas la paroi et l'intérieur reste lisse ; peu profonds, le rebord ne faisant que 3 mm d'épaisseur Anse séparée : posée à plat à droite de la tasse, côté +X, même couleur chocolat ; rayon de 22 mm, épaisseur de 10 mm ; extrémités découpées pour épouser la paroi ; se colle sur la tasse, sans creux de guidage ; s'imprime sans support sur sa face large Décorations séparées : sapin à trois étages et tronc sans étoile au sommet, deux étoiles latérales et quatre flocons, tous verts, 1,4 mm d'épaisseur, posés à plat devant la tasse côté −Y ; les deux flocons latéraux sont à environ 26 mm du centre et 42 mm de haut Creux d'encastrement des décors : profondeur d'environ 1,5 mm, 0,3 mm de jeu tout autour pour la colle ; la paroi garde environ 1,5 mm sous les creux et l'intérieur reste creux Points d'impression : prévu pour une FDM domestique ; les jambes du père Noël sont en porte-à-faux contre la paroi inclinée et ses pieds ne reposent pas sur le plateau, un peu de support peut être utile à cet endroit ; les branches des flocons font environ 2,4 mm de large, ce qui est fin pour une buse de 0,4 mm ; un flocon plat sur une paroi courbe reste une approximation La tasse sert de contenant pour des bonbons ou du chocolat chaud. L'anse et les décorations vertes s'impriment à part, chacune dans sa couleur, puis se collent : l'anse sur le côté de la tasse, les décorations dans leurs creux sur la face avant.
Yuletide Vault — 24-Drawer Advent Calendar
A print-in-place advent calendar with 24 identical sliding drawers in a 4 × 6 grid. Every drawer front carries an engraved number from 1 to 24 and a soft-edged finger handle, so the countdown opens one small compartment at a time. The drawer bodies, fronts and matching frame openings keep clean square corners; only the handles are rounded, giving a comfortable grip without softening the rest of the geometry. Each cavity is sized around a 35 mm × 20 mm candle, making the drawers practical for a daily treat or a small gift. The whole assembly fits the Bambu Lab A1 Mini build plate and prints without supports in the sliding channels. Features 24 identical drawers arranged in 4 columns and 6 rows, numbered 1–24. Square drawer bodies, fronts and frame openings; only the handles are softened, with an edge radius of about 1.5–2 mm. Each drawer has an 11 × 7 mm handle that protrudes 3 mm, centred on the front. Engraved numbers sit 0.6 mm deep in the strip above each handle, clear of the grip area. 0.4 mm clearance on every side and at the back keeps the drawers sliding freely. A stop ridge inside each pocket catches the drawer's back wall after about 40 mm of travel, so drawers cannot fall out accidentally. Drawer cavity: 38.5 × 42 × 22 mm, sized to hold a 35 × 20 mm candle. Dimensions Overall footprint: 175.2 × 154.2 × 49.6 mm including handles — fits the A1 Mini's 180 mm plate. Drawer outside: 41.5 × 45 × 23.5 mm; wall and floor thickness: 1.5 mm. Frame divider walls: 1.2 mm. Print notes The calendar prints as one piece with the drawers already seated in the frame. The back face lies flat on the plate and the fronts and handles face up, which avoids supports in the channels. Print in white PLA for the intended look.