Corner Guard — Tube Weight
Created 1 months ago
Description
The Corner Guard is a heavy, low-profile block designed to tame unruly pump outlet tubes. It tucks neatly into any wall corner against the baseboard, keeping 8.5mm tubing securely anchored and routing water exactly where it needs to go. Its heavily rounded top ensures that passing feet or sweeping brooms glance right off without dislodging the line.
Features
- Corner Fit: Flat back and left sides sit flush against the wall and baseboard.
- Tube Clearance: A 9.5mm continuous bore provides a smooth slide for standard 8.5mm OD pump lines.
- Anti-Kink Exits: Both ends of the passage are flared to prevent the tubing from creasing under tension.
- Deflective Shell: 15mm rounding on all exposed faces deflects accidental strikes.
Images
More like this
Explore more in Home & Fixtures →
280mm Irrigation Controller Enclosure
A rigid 280 × 200 × 90 mm printed enclosure designed specifically for an ESP32-based multi-zone plant irrigation controller. The layout divides the internal volume into three distinct areas: high-current power distribution on the left, six MOSFET drivers in the center, and the low-voltage microcontroller logic on the right. An extra-wide central cable channel runs between the two rows of MOSFETs, and all high-traffic access areas—like screw terminals and adjustment dials—have generous working clearances. The outer walls feature deep U-slots for cables, cut from the top edge so the main flat lid traps them cleanly in place without relying on separate cable glands. Internal Layout details Zone A (Power): Mounts for a 56×35 mm DC-DC buck converter, a friction-fit bracket stack for four WAGO 221-415 lever connectors, and a C-clip for an inline 5A barrel fuse. Zone B (Switching): Two rows of custom mounts for six 35×32 mm MOSFET boards. Each uses exactly two diagonal standoffs to leave maximum free space around the terminals. Zone C (Control): Stand-offs for an ESP32 NodeMCU, with a dedicated USB-C opening aligned in the external right-hand wall. Structure: Embossed floor labels mark all hookup zones. Cable tie bridges are scattered throughout the base for organization, and vertical ventilation slots flank the rear and sides. Uses four M3 screws driven directly into heavy internal corner bosses to seal the lid.
64mm Straight Cylindrical Pipe
A straight cylindrical pipe designed for flow or structural use, featuring a centered continuous bore. Inner Diameter: 60 mm Outer Diameter: 64 mm Wall Thickness: 2 mm Length: 60 mm Prints vertically without supports.
60mm Straight Hollow Pipe
What it's for A standardized straight hollow cylindrical pipe segment. Suitable as a structural spacer, a fluid/air channel, or a sleeve for cables and smaller tubes. The uniform 2mm wall is optimized for standard FDM printing parameters. Dimensions Outer Diameter: 60 mm Inner Diameter: 56 mm Wall Thickness: 2 mm Total Length: 60 mm Remix ideas Add flanges or threads to the ends for modular connection. Introduce a longitudinal slit to use it as a snap-on cable cover. Thicken the walls if intending to use under compressive loads.
Acoustic Cabinet Sealing Plug
A tailored sealing plate built to cap off a 48 mm port while cleanly passing through four heavy-gauge wires. The stepped rear boss drops straight into the MDF cutout, leaving the broad outer flange to hold the seal tight against the cabinet face. Build Details Main flange: 75 mm diameter Alignment boss: 48 mm diameter (8 mm depth) Routing ports: Four centered holes sized for 2.5 mm² speaker wire Hardware: Countersunk for 3 mm fasteners on a 43 mm square layout
Straight Cylindrical Pipe
A straight cylindrical pipe with a uniform wall thickness, designed for fluid transfer, structure, or sleeving. Inner Diameter: 60 mm Outer Diameter: 64 mm Wall Thickness: 2 mm Overall Length: 60 mm
Appendiabiti a Traliccio 32mm
Appendiabiti rigido a parete stampabile in 3D. Disegnato con un profilo sagomato per ridurre il consumo di filamento mantenendo un'elevata resistenza al carico. Interasse: 32 mm esatti. Fori: 3,2 mm (per viti da 3 mm), con svasature da 4,5 mm posizionate a profondità fissa. Accessibilità: tunnel orizzontali da 8,5 mm per inserire agilmente vite e cacciavite. Orientamento: Da stampare rigorosamente coricato sul fianco per sfruttare la direzione dei layer.