SUPPORT PRINTYTRON
New Model
Loading 3D preview…

Hideaway — Türrahmen-Batteriebox

Made by Opopa141

Created 2 days ago

Home & Fixturestuerrahmenhakenbatterieboxlichterketteverstecktseitenauslasseinteilig
Remix this model →

Remixed once

Description

Hideaway ist eine kleine, oben offene Box mit Haken, die über einen Türrahmen gehängt wird und eine Batteriebox für Lichterketten verdeckt. Der Haken sitzt an der Rückseite, der Kabelausschnitt wandert seitlich aus der Box, damit die Vorderwand geschlossen bleibt.

Maße

  • Innenraum: 62 × 30 × 24 mm (passend für eine 3×AA-Batteriebox)
  • Haken: für Türrahmen von ca. 20 mm Dicke, 40 mm breit
  • Wandstärke: 2,4 mm
  • Kabelausschnitt: 8 × 8 mm in der rechten Seitenwand, knapp über dem Boden

Hinweise

  • Ein Teil, kein Deckel – oben offen
  • Vorderwand geschlossen, Kabelauslass seitlich
  • Ohne Stützen druckbar, Rückseite flach auf das Druckbett

Images

SUPPORT PRINTYTRON
Tip Jar
Printytron built this for free. If it saved you a trip to the shop, a tip helps keep it free.
Need filament at a great price?
Printing this one? Stock up through our eSun partner link — your price stays the same, but Printytron gets a small commission to go towards our costs.
Door-Top Hook STOP Sign Hanger

Door-Top Hook STOP Sign Hanger

A door-top hook sign for hanging over a door top or peg: a 95 × 160 × 5 mm plate with a one-piece flat hook on its top edge. The hook is a ring with a gap on its lower right, about 68 × 69.4 mm overall and 5 mm thick, reaching roughly 68 mm above the plate. Its ring wall is about 10 mm thick; the opening is fixed and does not adjust. Below the hook is an octagonal STOP sign with white lettering, then the message in dark raised text: six lines at one 6 mm size in a bold condensed face, with a blank line after “No Politics”: No Soliciting No Religion No Politics Ignoring this guarantees we will not use or purchase your product/service. It replaces a paper or card door hanger of similar footprint — nothing to laminate and nothing to tape up. Fits A door top or peg that clears the hook’s fixed opening — measure the opening against the actual door top or peg before printing, as nothing on the part takes up slack. A print bed at least 160 × 95 mm, since the plate prints flat. A one-piece print: plate, text, STOP sign and hook print together; no separate loop, screws, nuts or fasteners. Check before printing Measure the hook opening against your door top or peg. The ring wall is about 10 mm thick and the opening is fixed. Print the plate flat so the layers run along the hook. At roughly 68 mm of reach in a 5 mm section, the hook is a long cantilever; printing it stood on edge risks snapping it. Change filament at the layers where the red, white and dark areas begin if you want clean colour separation. Line spacing is about 9.2 mm pitch. The last line of text sits about 4 mm from the plate’s lower edge, so preview the layout and margin before committing to a long print. Known limits One hook thickness only, 5 mm — there is no heavier version. No through-slot for a knob or handle, and no screw-on loop or M3 hardware. The sign does not clamp or lock to the door; it hangs from the hook and lifts off. The hook opening is fixed; it does not adjust for different door tops or pegs.

BraveCrimper · 15 hours agoRemix →