Cricket Calcium Duster Tube With Inner Screen
Created today
Description
Cricket calcium duster tube where the powder sits in one cap, crickets get dusted when shaken, and nothing needs a loose divider. A coarse screen is printed into the tube near the bottom, so powder passes up through it and crickets stay above.
- Tube: 75 mm outside diameter, 70 mm bore, 2.5 mm wall, 154 mm long, with 16 mm coarse threads (5 mm pitch) on both ends.
- Screen: 1.6 mm thick, 4 mm square openings on a 5.6 mm pitch, 22 mm up from the bottom end, fused to the tube wall.
- Caps: two identical solid caps, 0.8 mm thread clearance for PETG, grip ribs on the outside.
- Printing: body stands upright, caps print top-down; the 4 mm screen openings bridge without supports.
Images
More like this
Explore more in Home & Fixtures →
Fenstergriff-Halter Block 110x20x30 mm
Block mit 110 x 20 x 30 mm und zwei Aussparungen an der Unterseite zum Einhaken in Fenstergriffe. Die Aussparungen haben unten gerade Wände und oben eine runde Form (Ø25 mm). Die Öffnung ist mit 21 mm etwas schmaler als der Griff, damit dieser einrastet. Maße: 110 x 20 x 30 mm, Kanten 1,5 mm angefast Aussparungen: Ø25 mm rund oben, 21 mm breite gerade Öffnung unten Mittenabstand: 70 mm Durchgehend durch die 20 mm Breite Material: PLA oder PETG, ohne Stützen druckbar
64mm Straight Cylindrical Pipe
A straight cylindrical pipe designed for flow or structural use, featuring a centered continuous bore. Inner Diameter: 60 mm Outer Diameter: 64 mm Wall Thickness: 2 mm Length: 60 mm Prints vertically without supports.
Reinforced 8mm Irrigation Y-Splitter
A heavily reinforced Y-shaped hose connector built specifically to merge two fluid lines into one. Designed for 8mm inner-diameter flexible tubing, it uses a solid central hub rather than thin overlapping walls, ensuring the part handles pressure without snapping at the junction. The internal geometry is sculpted to maintain flow: a 6mm channel through the main body prevents a bottleneck at the merge, smoothly necking down to 5mm inside the barbs to guarantee thick, watertight perimeters where the plastic gets thinnest. A precision flat cut on the underside allows the entire assembly to drop straight onto the build plate, completely eliminating the need for support material. Remix Hooks & Constraints Hose Fit: The double barbs peak at 8.5mm OD and drop to a 7.2mm valley, grabbing 8mm ID silicone or vinyl hose tightly. Print Settings: Built for PETG or ABS. Use 4 to 5 perimeters to ensure watertightness and maximum mechanical strength against bending forces. Scaling: Scaling up works cleanly for larger hose (e.g., 125% for 10mm ID), but scaling down is not recommended as the internal channel will restrict flow and the walls may drop below the required thickness for a watertight seal.
Wall-Mounted Bedside Floating Shelf
What it's for A sleek floating shelf for beside the bed at about head height, sized for an ornament or a small potted plant. A back plate with four countersunk screw holes fixes it to the wall, and two triangular brackets support the top. The design is symmetrical, so printing two gives a matching pair for each side of the bed. Dimensions Shelf top: 200 × 120 × 12 mm, rounded edges Back plate: 170 mm wide, 6 mm thick, 70 mm tall including the shelf Screw holes: four, 4.5 mm shank with 9 mm countersink, set 80 mm apart, the upper pair just below the shelf Brackets: two, 6 mm thick, at X ±70 mm Print notes Prints with the top face on the bed, with no supports needed. Use wall plugs suited to your wall type and countersunk screws with heads up to 9 mm. Remix ideas Narrow the shelf for tighter spaces. Add a small front lip to keep ornaments from sliding off. Add a cable notch for a bedside lamp.
120mm Wavy Suspended Planter Pot
A contemporary, self-supporting planter insert designed to seat perfectly into a matching 130mm water reservoir. The exterior features a 12-point wave pattern with a gentle 45-degree sweeping twist, merging seamlessly into a robust 120mm upper resting lip. The interior taper mirrors the outer walls to maintain a reliable 2.5mm thickness, finishing with an elegant inner flare at the rim. Specifications Dimensions: 140mm height, 120mm max outer diameter (at the rim). Clearance: Tapered base drops to ~107mm diameter to comfortably clear standard 130mm reservoir walls. Drainage: Seven 5.5mm functional ports arranged flush to the floor. Printability: The support lip is carried by a calculated 45-degree transition collar, ensuring the overhang prints completely clean without supports. Drops right onto the build plate.
Tank Tap Bulkhead Fitting 1 1/2" BSP
A through-wall bulkhead fitting in the spirit of a classic water butt tank connector: a broad round flange sits against the tank wall, a long threaded barrel passes through, and a matching lock nut clamps it from the other side. 72 mm flange with a shallow gasket seat for a flat washer or O-ring 1 1/2" BSP-style male thread (47.8 mm major diameter, 11 TPI), 40 mm long 38 mm through bore Separate lock nut, printed alongside Design notes: The thread is a generic approximation of the Whitworth form, so test-fit against your mating part. Cut the tank hole to suit the thread, and use a rubber gasket against the flange. Print the flange face-down; PETG is a sensible choice for water contact.