Customizable - Dust Collector Hose Adapter
Created 4 months ago
Description
[Customizable] Remix this model and provide your desired hose sizes to adapt and the model will regenerate for your needs. [Smoooooooth] It's smooth as for optimal airflow.
A convenient adapter to connect a 2-inch dust collection hose to a 4-inch extractor system. Features internally smooth walls and gentle tapers on the 2" and 4" ends to securely slide into standard flexible hoses.
Photos
Technical views
More like this
Explore more in Workshop & Tools →
Threaded Irrigation Hose Adapter
What it's for A female-to-female adapter designed to link a stackable irrigation pipe to a standard garden hose. One side features a standard 3/4"-11.5 GHT garden hose thread, while the other side is threaded to screw directly onto the pipe's male fitting. Dimensions Overall length: 38 mm Hex body: 42 mm (circumscribed) for easy hand or wrench tightening Bore: 19 mm straight through to match the pipe's internal diameter and eliminate flow restriction Design notes The internal bore transitions smoothly into flat seats on both ends, allowing standard hose washers or O-rings to seal perfectly against the fitting. The thick hexagonal walls withstand outdoor water pressure without flexing.
Stud-Saddle Drop Shelf
A heavy-duty drop shelf designed to wrap a standard 2x4 wall stud. The main bed splits into two pieces for easy printing on a standard bed, locking together with precision alignment dowels. A central support leg drops down directly into a face-mounted stud bracket to hold heavy loads flat. No-Support Printing: The main plates are oriented perfectly flat off the bed. Locked-In Support: The drop leg features a tubular bottom that seats perfectly into a cupped bottom bracket, preventing lateral slip. Hardware Needed: A few 6mm rod pins for the hinges, and standard countersunk wood screws for the brackets.
Machined-Style NPT Blow Gun Nozzle v4
An air compressor adapter designed to interface a 1/4" NPT blow gun with a precise 3mm outer-diameter nozzle. The part features a clean, support-free geometry that steps inward as it prints, transitioning smoothly from a 14mm hex base up through the threads, capping off with a reinforced 1mm fillet at the base of the delicate tip. Print and Application Notes Print Orientation: Prints exactly as oriented (hex base flat on the bed). No supports are required for the threads, ceiling, or nozzle. Sealing: The threads are rendered straight rather than tapered—wrap with a couple of layers of PTFE thread tape to ensure a tight pneumatic seal when threading into the metal gun. Material: PETG or ABS is highly recommended over PLA to handle the pressure spikes and avoid brittleness at the tiny 1mm bore tip.
1/4" NPT Golf Grip Air Adapter v2
Adapter to mate a 1/4" NPT air compressor blow gun directly to a golf club grip vent hole. Uses a 16mm hex drive for tightening. Fitment Notes Mating Surface: 1/4" NPT female blow gun ports. The model uses a straight 18 TPI thread (13.5mm OD) that relies on Teflon tape to seal against the tapered female bore. Output: 3mm OD nipple, 4mm long. Backed by a 3mm conical shoulder to prevent snapping under pressure. Bore: 1mm continuous air channel. Check this after printing — a 1mm FDM hole will likely need clearing with a wire or a 1mm drill bit before it flows air properly.
Wall Mounted Multi Tape Dispenser
A wall-mounted multi-roll tape dispenser designed for workshops, packing stations, and craft benches. The bracket holds standard rolls of masking, painters, or packing tape on a central spindle and provides a rigid front tear bar with serrated teeth for clean one-handed pulls. What it's for Organising multiple rolls of workshop tape on a single wall-hung fixture so individual rolls can spin freely and be torn to length without chasing loose rolls around the bench. Dimensions Overall Width: 200 mm total width (180 mm usable tape span between arms) Wall Height: 90 mm backplate with 4x countersunk screw holes Wall Reach: 130 mm forward projection Spindle Diameter: 19 mm rod fitting standard 1" (25 mm) or 3" (76 mm) tape cores Print notes Print the main wall mount frame flat on its rear backplate or on one side face to eliminate tall support overhangs. The removable spindle prints horizontally with a small brim or vertically in two halves if your build height allows.
Knurled Tripod Thread Adapter
A threaded step adapter for mounting 3/8-16 photography and audio equipment to standard 1/4-20 tripod studs. The flanged base features a deeply scalloped outer diameter to allow firm, tool-free tightening. Specifications: Base Thread: 1/4-20 UNC (female) Top Thread: 3/8-16 UNC (male) Grip Style: Scalloped profile Tolerances: Thread profiles offset for FDM printability