CycMount — Toolless Camera Clamp
Created today
Description
Introducing CycMount, a robust camera mount engineered to secure action cameras to standard 22mm bicycle handlebars. Built with frequent swaps in mind, it utilizes custom wing nuts for a completely tool-free installation, allowing quick transfers between bikes. The integrated three-prong interface is precisely dimensioned with 3mm thick fingers on a 5mm pitch, ready to accept standard action camera housings and a 5mm pivot bolt.
Design Features
- Strength by Orientation: Both clamp halves print flat on their sides, aligning the layer lines perpendicularly to the clamping stress for maximum strength.
- Support-Free: The horizontal print orientation ensures the 22mm handlebar bore and the 5.2mm pivot hole print perfectly round without requiring slicer supports.
- Tool-Free Adjustments: Includes two custom wing nuts designed with integrated M5 hex nut traps.
Required Hardware
- 3× M5 Hex Nuts (two for the wing nuts, one for the bottom clamp)
- 2× M5 Cap Head Bolts (for the main clamp body)
- 1× M5 Bolt (for the camera pivot)
Images
More like this
Explore more in Automotive, RC & Hobby →
Faceted SimHub Button Box
A clean, industrial-styled button box designed for sim racing rigs, controlling Wind, Pedals, and Bass Shakers via SimHub. The enclosure uses a faceted, dodecahedron-inspired geometry to eliminate flat overhangs and keep the footprint small. The front panel cuts a heavy 45° chamfer, hiding the seam where it snaps into the rear body. Features internal snap-fit prongs and receiver towers — no visible hardware required. Base dimensions reduce sharply toward the mount to avoid interfering with wheelbases or monitor arms. Built with clearances for standard Cherry MX switches and a toggle switch cut out for the top left.
Solid Core Quadcopter Frame
A solid unibody quadcopter frame designed to hold four micro drone motors. Features: Solid central chassis block Swept structural arms Motor mounts with clearance for 8.5mm motors Unified 8mm frame thickness with 7.5mm arms
20
Model truck wheels usually snap at the hub or require a nest of supports just to print the rims. This one prints entirely flat on the bed, bridging cleanly across the inner rim recess, with treads chunky enough to actually grip rough surfaces instead of spinning out. Specifications Diameter: 80 mm Width: 30 mm Axle: 8 mm hex shaft Print orientation: Flat on its side (no supports needed)
10
Left half of a structural truck chassis, designed with a flat interior face to mate directly to a mirrored right half. Length: 500 mm Wall Thickness: 4 mm structural ribs Mating: 8 mm alignment pegs and one center hole with 0.3 mm clearance Weight Reduction: C-channel styled underside cutouts
12
Large vehicle prints warp, lift off the bed, or take days to finish. Splitting the chassis into smaller, hollowed quadrants stops the curling and lets the pieces finish quickly. This is the left-side foundation. Fit Details Overall Dimensions: 140 mm × 70 mm × 12 mm Wall Thickness: 3 mm perimeters and floors for rigid bridging Mating Pins: 5 mm diameter pins into 5.3 mm receiver holes for a clean press-fit Panel Mounts: Four 6.3 mm top sockets align the upper body elements
11-Camion
Heavy-duty front bumper assembly for 80mm standard RC frame rails. Designed specifically as the forward module for the Moroccan Unity Day parade truck layout. Replaces standard flat-plate bumpers with a wrapped 45mm profile. The decorative emblem sits flush against the primary face to eliminate support material requirements during FDM printing. Mating Surfaces to Check Rail Spacing: 80mm center-to-center. Mounting Hardware: 3.5mm vertical bores set 15mm back from the bumper plate, suited for M3 bolts with standard 0.25mm operational clearance. Overall Clearance: 160mm total width; verify your wheel sweep won't clip the 40mm overhangs on standard steering throw.