Made by a Guest
Created today
Description
A vertical stand that docks two closed laptops side by side on their edges, freeing up desk space. Built for a setup with a work laptop and a personal laptop sharing one desk. Each slot has a window cut through its walls, so a hand can rest on a lid to check for heat without removing the laptop.
Images
A hexagonal desk cup with the twist built into its silhouette: the six-sided body rotates 70° from bottom to top, so the facets read as a slow spiral rather than a straight column. It stands 90 mm tall and measures about 83 mm across the corners — enough for pens and pencils, with room to spare for scissors or a ruler. The hexagon sits flat on the desk, giving it the weight of a solid block rather than a floating one. Walls are 3 mm and the floor is 4 mm, so it holds its shape under a full load without feeling heavy. Dimensions Overall height: 90 mm — takes pens, pencils, scissors and a ruler Width across corners: about 83 mm Wall thickness: 3 mm Floor thickness: 4 mm Features Six-sided body with a 70° twist from base to rim Flat hex base sits directly on the desk for a stable, blocky stance One named area, Twisted Cup Body, printed as a single piece Flat facets catch the light along the spiral Print notes Print upright as oriented on the plate. The twist is gentle enough that the walls lean without needing supports, and the flat hex base gives a broad, secure contact patch. A matte dark filament shows the spiral facets best; 0.2 mm layers with two or three perimeters make a sturdy cup, and a finer layer height sharpens the edges of the twist.
What it's for A minimalist desk organizer with four open-top compartments for pens, pencils, markers and small stationery. A stepped front lowers the front pair for easy reach to small items, and a small NEXUS logo is engraved on the front face. Dimensions Footprint: 120 × 80 mm Height: 95 mm rear, 60 mm front Wall thickness: about 2.4 mm Flat base, rounded vertical corners, chamfered base edge Remix ideas Change the logo text to a name or initials. Make the front compartments deeper for scissors or rulers. Add a non-slip pad under the base.

An upright charging dock for a wireless earbud case, sized for a desk. The case sits in a 50 × 30 mm pocket, 12 mm deep, on a 60 × 45 × 28 mm base with rounded corners and a flat bottom. A 10 mm notch at the back of the pocket routes a charging cable to the case, and a 4 mm front lip above the pocket floor keeps the case from sliding forward. It replaces a loose case sliding around the desk with a fixed upright position. Fit check Fits: wireless earbud cases with a footprint no larger than 50 × 30 mm and a charging port that faces the rear notch. Does not fit: cases wider than 50 mm or deeper than 30 mm; cases with a bottom-only charging port, because the pocket floor is solid and the notch opens only at the back. Check before printing: measure your earbud case footprint and confirm the 10 mm rear notch lines up with the charging port and plug. Print: one connected piece with a flat bottom and rounded edges, designed for reliable FDM printing on an older printer. No separate pieces or assembly.
What it's for A retro-styled desk organizer that keeps pens, cards and small items in one place. A teal pen tower, a card or phone slot and two open trays sit on an amber base. A red racing stripe runs along the front. A cream arched backrest has a round window and embossed "80's & more" lettering following the curve. Dimensions Base tray: 160 × 80 × 12 mm Pen tower: 40 × 50 mm footprint, rising to 50 mm overall height Card / phone slot: 40 × 10 mm opening Front tray: 40 × 28 mm Large right tray: 54 × 50 mm Arched backrest: about 90 mm wide, top at 57 mm Lettering: embossed 1 mm, 7 mm tall Remix ideas Change the lettering to a name or a different slogan. Resize the trays for coins, clips or sticky notes. Recolour the stripe and backrest to match a different retro palette. Widen the card slot for a tablet.

A hexagonal desk cup, 80 mm tall and 100 mm point to point, split into two sections by an internal divider wall. The larger section runs full height and holds pens and pencils. The smaller section is cut down to one third of that height, about 27 mm, and works as a tray for paper clips, erasers and other small items. The divider sits slightly off-centre so the short tray takes up roughly 40% of the floor area. The walls are 2.4 mm thick and the base is 3 mm thick. The top and bottom outer edges have a small chamfer. Overall size: 100 mm across corners, 80 mm tall Tall pen section: full height, about 60% of the floor Short tray section: one third height, about 40% of the floor Wall thickness: 2.4 mm, floor thickness: 3 mm Prints upright as one piece with no supports needed
Geared tilting tablet stand for the Doogee U11, laid out as 14 separate flat pieces for printing and assembled by hand after printing. A knob on a drive shaft turns two 30-tooth gears that mesh with 15-tooth gears on the cradle, so a small knob twist tilts the cradle forward or back. Pieces Base plate: 1 Side plates: 2, with tabs that drop into slots in the base Tablet cradle: 1 15-tooth cradle gears: 2, peg into the cradle ends 30-tooth drive gears: 2, keyed to the drive shaft Knob: 1 Axle: 1, 8 mm round Drive shaft: 1, D-profile Friction-fit caps: 3 Print notes Every piece is laid flat on the build plate with no overlap. Gear pegs face up and the shaft flat faces down, so no supports are needed for the main bodies. Clearances are about 0.2-0.4 mm; adjust for your printer. Gear mesh and fit are untested; friction alone holds the tilt angle.