Fairy-Tale Flat-Print Tree Organizer
Created today
Description
This flat-pack, two-piece organizer channels a storybook woodland silhouette while keeping print times fast and failures low. The tree geometry is laid completely flat on the print bed, dodging the need for support material entirely. Once the plate is finished, it slots vertically into the heavy river-stone base to stand upright, offering nineteen upward-angled pegs to hold small items.
Print and Assembly Notes
- No Supports Required: Both the tree profile and the upward-facing mushroom hooks are designed to clear overhang limits naturally.
- Sturdy Assembly: A deep mortise in the base block holds the flat-printed trunk firmly in place.
- Utility: Ideal for hanging rings, light necklaces, keychains, and hair ties.
Images
More like this
Explore more in Storage & Organization →
14-Compartment AM/PM Pill Organizer
A seven-day medication organization tray featuring 14 separate compartments for AM and PM dosing. The base tray accommodates individual friction-fit lids embossed with day-of-the-week initials and corresponding sun or moon indicators to separate morning and evening tablets. Compartment Volume: 25x25x15mm interior capacity per slot. Lid Fitment: Friction-fit covers with a 0.3mm clearance flange. Labelling: Embossed text and iconography for tactile identification. Format: Lids and base separated for flat build-plate orientation.
Splice — Magnetic Hard Case
A rugged, two-piece protective case engineered to house bulky, wraparound eyewear. The two halves print flat and assemble via a robust mechanical hinge, securing shut with discrete magnetic closures. Features Filament Hinge: Designed to accept a length of standard 1.75mm filament as the pivot pin, producing a perfectly tight, metal-free joint. Magnetic Closure: Four dedicated pockets in the front corners accept standard 6×2mm round magnets for a satisfying, hardware-free snap. Dust Lip: The base features an extruded inner ring that mates seamlessly with a corresponding channel in the lid, ensuring precise alignment and keeping debris out. Dimensions Exterior: 165 × 75 × 60 mm (closed) Internal Clearance: 159 × 69 × 54 mm Walls: 3 mm solid perimeter Assembly Notes Print both halves flat on the bed. Once complete, insert the magnets into their corresponding pockets (a drop of CA glue is recommended), align the back knuckles, and thread a piece of 1.75mm filament straight through the hinge line. Snip the excess filament flush.
SG2016P Switch Rack Ears
Desktop switches left dangling by their patch cables or sliding around on top of rack gear are a preventable mess. These custom rack ears bolt right into the side of a TP-Link SG2016P, bridging the gap to a standard 19-inch server rack so it actually stays put. Fit and Fabrication Span: Bridges an 89.5mm gap per side (assumes a 286mm wide switch). Side Mounting: Features three generous slots rather than fixed holes, accommodating variations in where TP-Link drills their chassis. Uses standard M3 or M4 screws. Rack Mounting: Standard 1U slotted holes (31.75mm center-to-center). Printing: Both ears lay flat on their front face. Zero supports required. Print in PETG or ABS if your rack runs hot, though standard PLA is structurally fine for a switch this light.
Monolithic Helmet Hook
A robust, monolithic wall hook designed specifically for the bulk and straps of bicycle helmets. The sweeping, angled arm reaches out far enough to clear the wall, terminating in a rounded lip that won't dig into foam liners or fray fabric straps. Built to print cleanly standing up, the overhang angles are steep enough to self-support on most FDM machines. Mounting Details Backplate: 120mm tall by 40mm wide, distributing the load. Hardware: Two standard 5mm countersunk screw holes. Clearance: The upper screw hole is positioned well above the hook's lip to ensure a screwdriver can reach it straight-on without interference.
GridLock — Split Open Drawer Frame
GridLock is a custom-fit drawer divider system completely stripped down to its essentials. Sized specifically to frame out compartments without wasting material on a floor, this open-grid organizer drops directly into a drawer, letting the existing liner or wood bottom show through. The frame has been split into four cleanly cut sections to allow printing a large 13.5-inch wide organizer on standard 220mm square print plates. Dimensions Total Assembled Footprint: 342.9 mm wide × 228.6 mm deep (13.5" × 9") Height: 25.4 mm (1") Maximum Piece Size: 171.5 mm × 114.3 mm (fits comfortably on an Ender 3 or Prusa MK series) Layout One full-width front compartment (3.5" deep). Two back compartments (one exactly 3.5" wide, the other filling the remaining space). No bottom—sits flush on your drawer base. Assembly Notes The four quadrants print completely flat without supports. Because the perimeter walls are thin to maximize storage space, they use straight flush cuts rather than bulky joints. Just add a drop of superglue (CA glue) to the seams, press them together on a flat surface, and you're good to go.
Aufsteck-Schraubklemme mit Haken
Eine umstrukturierte Klemmhalterung, die sich als offenes U-Profil direkt über ein 15 x 15 mm Vierkantrohr stecken lässt. Die Fixierung erfolgt durch eine gedruckte M10-Druckschraube auf der Rückseite, die das Rohr fest gegen die Vorderwand presst. Auf der Frontseite sitzt ein massiver Haken. Anpassungsmöglichkeiten für Remixes Dieses Modell ist so ausgelegt, dass die grundlegenden Klemm-Mechanismen leicht für andere Einsatzzwecke skaliert werden können: Stangenmaß: Der innere Ausschnitt hat aktuell 15,6 mm Breite für etwas Spiel auf 15 mm Stangen. Wer größere Rohre nutzt, kann den Hauptkörper entsprechend verbreitern. Haken-Geometrie: Der Ausleger ragt 12 mm nach vorne, die Spitze zieht 16 mm nach oben. Das lässt sich gut durch flache Halterungen oder Ösen ersetzen. Gewinde: Das M10x2 Gewinde hat im Gehäuse 10,6 mm Durchmesser (intern). Für mehr Klemmkraft auf glatten Metallrohren kann die Schraube gegen eine Standard-Metallschraube mit Gummipad getauscht werden.