Made by a Guest
Created 3 days ago
Description
A set of eight small label plates with raised white lettering, each 1 in × 0.5 in. Blue plates read ROAD, CURB, REAR, REAR; red plates read SCENE, DECK, TANK, TANK. Intended for marking bins, shelves, hooks or parking spots.
Images

Open-top storage box with three equal compartments side by side, and the name CHARO raised across the full front face. Outer size: 210 x 112 x 85 mm Walls and dividers: 3 mm Floor: 4 mm Compartments: 3, each about 66 x 106 mm inside Lettering: Bebas Neue, about 200 x 77 mm, raised 1 mm on the front Prints upright with no supports
What it's for A plain open-topped square box with a closed floor, sized to hold small parts, tools, or loose odds and ends on a desk or workbench. The straight sides and flat base keep it stable on the print plate and easy to drop things into from above. Dimensions Outer footprint: 75 × 75 mm Height: 25 mm Wall thickness: 3 mm Floor thickness: 3 mm Top: fully open, no lid Print notes Prints upright as it sits, with no supports needed for the vertical walls. A 3 mm wall and floor hold up well in PLA or PETG at a standard layer height; thicker walls take a slightly wider nozzle or more perimeters comfortably. Remix ideas Add a lid or a stacking lip so several boxes can sit on top of one another. Round the outer corners for a softer look and less sharp handling. Divide the interior with a grid to sort small hardware.
PivotTee è un portabrugole piatto per chiavi a T da 10 a 3 mm, con perni laterali che lo fanno ruotare da orizzontale a verticale su una base da fissare al cassetto. Un fermo girevole dietro il blocco lo tiene in verticale durante l'uso, e il perno centrale accoglie un inserto filettato M3 per avvitare il fermo. Caratteristiche Otto sedi da 10 a 3 mm con fessura superiore e numeri incisi Base con due fori svasati da 5 mm Perno del fermo da 8 mm con foro da 4,2 mm per inserto M3 (profondità circa 8 mm) Fermo girevole 44 × 14 × 6 mm Print notes Tre pezzi stampati sdraiati, senza supporti Inserto filettato da scaldare a caldo nel foro del perno
flare tubintake for stove
Loose items slide around in a drawer, and a floorless box with a divider keeps them in place. This one is a rectangular frame with no floor and a full-height wall across the middle. Key numbers Outer size: 184 x 93.33 x 115 mm (height) Wall thickness: 2.4 mm Divider: 2.4 mm, full height, at the middle of the 184 mm length Three boxes side by side fill a 280 mm drawer depth Print: open end up, no supports needed, fits beds of 210 mm or larger
Liftlatch is a modular desk storage module built from a rounded outer housing, a sliding drawer, and two bowtie joiner clips. The design language is quiet and symmetrical: thin 1.6 mm walls, soft 6 mm fillets down all four vertical corners, a flush front with a recessed finger pull, and completely flat outer side walls that stay within 82.0 mm. A single unit reads as a smooth box; a row reads as a bank of drawers, joined by clips that sit flush in dovetail slots rather than protruding rails. Units stack vertically on a 2 mm lip and matching underside pocket, and lock side-by-side with the separate clips, so the system grows from one 82 × 165 × 55 mm module without changing hardware. The housing, drawer and clips are laid out separately on the plate; the housing prints standing on its back wall with the open front facing up, which removes the wide ceiling bridge and keeps the side slots vertical for a support-free print. Dimensions Module footprint: 82 × 165 × 55 mm nominal Housing as laid out: 82 × 57 × 165 mm, standing on its back wall with the open front facing up Drawer as laid out: 76 × 162.6 × 49.1 mm, flat on its base with the open top facing up Joiner clips: two bowtie clips, each about 35 mm long and 5.8 mm wide, lying flat in the 15 mm gap between housing and drawer Walls: 1.6 mm base wall, thickened locally to 2.6 mm around the side slots Corner radius: 6 mm on all four vertical corners of the housing, matched on the drawer front so it sits flush in the rounded opening Drawer clearance: 0.4 mm at the thickened slot sections; the drawer is narrowed to 76 mm, leaving about 1.4 mm of play per side elsewhere Stacking lip: 2 mm stepped lip on top with a matching recessed pocket underneath, both following the same 6 mm corner path Side joinery: flush 1.2 mm deep dovetail slots in both outer side walls, with matching bowtie clips and 0.2 mm clearance; joined units sit flush with no gap Catch: 2.8 mm tab on the drawer's rear top edge meets a 2.5 mm stop lip under the front ceiling, with a 4 mm gap above the drawer walls Features Lift-to-remove catch: the rear tab catches the front stop so the drawer cannot fall out accidentally. Lift the front slightly to drop the tab clear of the stop and pull the drawer free; the overlap is about 1 mm, so the motion is short. Flush front: a 2 mm deep recessed finger slot with a 1 mm flare at its mouth, and a 1 mm chamfer around the front face perimeter, keep the face smooth to the touch and flat enough to stack. Symmetrical side slots: both outer walls are flat and clean, with nothing protruding. The bowtie clips slide in from the bottom of the housing to join neighbouring units flush; leave them out when a unit stands alone. Open back frame: a large chamfered cutout in the rear wall trims filament without weakening the structure. Stackable and joinable: the top lip and underside pocket align stacked units, while the flush slots and bowtie clips hold a row together side-by-side, gap-free. Print notes Every internal overhang is chamfered or tapered at 45° where needed — including the ledge under the front stop and the stacking lip tip — so the housing, drawer and clips print without supports, in a single colour with no multi-material setup. The housing stands on its back wall, the drawer lies flat beside it, and the two clips lie flat in the 15 mm gap, so the side slots print vertically and the wide ceiling bridge is gone. All printed elements fit a 180 × 180 mm Bambu Lab A1 mini bed with only a small margin, and the housing's 165 mm height sits close to the printer's height limit, so keep the spacing as laid out. The drawer walls are straight from front to back; the drawer is narrowed to clear the locally thickened slot walls, so check that it slides freely once inserted into the housing after printing.