Made by DamieLou
Created 2 days ago
Description
A flat, round hanging ornament shaped as a smooth spiral curl. The spiral is one continuous band that swells through the middle and thins to fine points at both ends, like a calligraphy stroke, with even spacing between turns. It lies flat, so the ornament sits close against a tree branch or a wall instead of projecting outward. A round hanging loop sits at the top at the 12 o'clock position, and the whole ornament prints as one piece in a single color.
Specs
Photos
Technical views
Evergreen Ring reduces the Christmas ornament to a clean silhouette: an open circular ring with a hanging loop, a pair of small three-tier trees tucked into the lower-right corner, and a large six-armed snowflake filling the top-left, its outer arms running into the ring and clipped by it. The right-hand tree sits fully inside the hoop, its tiers clear of the ring, with only its trunk running down into the bottom of the ring. The companion tree to the left is about 1.5 mm larger, with roughly 1 mm separating the pair, so the motif reads as a deliberate little grove rather than a repeat. The snowflake is centred about 12 mm in from the corner, and the arms that meet the ring are what hold it in place. Ring, trees and snowflake all stand the same 3 mm tall, giving the piece a single even plane that sits flat against a branch, a window or a gift tag. Every element is joined to the hoop, so the whole ornament prints as one solid piece with no assembly and no loose parts. Dimensions Ring: 60 mm across, 66 mm tall overall including the hanging loop, 3 mm thick Trees: two small trees occupying roughly 23.4 × 15.6 mm combined, 3 mm thick Snowflake: about 32.8 × 34 mm, 3 mm thick Features Open-ring ornament with an integrated hanging loop Two small three-tier trees side by side in the lower-right corner, with the tiers fully clear of the ring One tree about 1.5 mm larger than the other Large branched snowflake in the top-left corner, its outer arms cut off by the ring and fused to it Only the tree trunks and the snowflake's outer arms meet the ring, keeping the scene connected Uniform 3 mm thickness across every part Prints as a single piece, no supports needed Print notes Lay the ornament flat on the plate; the even thickness means no tall overhangs Any filament works — use contrasting colours for the trees and snowflake if you print in multiple colours
A hollow Christmas bauble with a six-armed snowflake cut through the front and back. The snowflake branches are set at a 40° angle so no island of shell is trapped between them; the cutout stays one connected shape. Rings of small round through-holes sit above and below the middle, and the equator is left plain. Raised bands run above and below the equator, and a cap with a hanging loop sits at the top. The bottom is flattened into a small footing so the ornament can stand upright on the print plate; the curved lower sides generally need supports. Specs Overall size on the print plate: 59.9 mm wide × 59.7 mm deep × 71.5 mm high Ball diameter: 60 mm Wall thickness: 2.5 mm, hollow shell Bottom footing: about 19 mm across Cutouts: one six-armed snowflake through the front and one through the back, about 22 mm across with fine branches around 1.8 mm thick Snowflake branches: 40° branch angle, arranged so no detached wall islands are left inside the cutouts Dot holes: 12 above the middle and 12 below, each a 3.2 mm hole straight through the wall; no hole row at the equator Bands: raised rings above and below the equator Top: cap with hanging loop Printing: single piece; supports needed on the curved sides Use: Christmas tree ornament or hanging decoration; the flattened base also lets it stand on a flat surface
What it's for A flat, two-dimensional Christmas tree cutout with six stacked, tapering tiers over a short trunk. The tip is a plain point — no star, no topper — and the silhouette stays clean and unbroken. Seven small stars and seven small circles are scattered across the tiers as through-holes in those same shapes, punching light through the flat body and adding detail without any surface relief. It prints as one flat piece and comes off the plate ready to use, with no assembly and no supports. Dimensions Overall footprint: 70 mm wide × 98 mm tall Thickness: a constant 4 mm Tiers: six stacked branches Star holes: 7 through-holes, roughly 2.6 mm across the points Circle holes: 7 through-holes, 3.6 mm across Top: plain pointed tip, no star All of the star and circle holes sit inside the tree's outline, including the ones near the tip, so nothing breaks the outer silhouette. Print notes Print flat on the plate. The constant 4 mm body means there are no overhangs and no supports are needed. The holes are small, so a 0.4 mm nozzle prints them cleanly; the star points are sharp and may round off slightly. The flat faces are a good place for a colour change or a two-tone filament swap. Remix ideas Scale the outline up or down for a larger wall piece or a small tag. Thin the body to 2–3 mm for a lighter decoration, or thicken it for a freestanding table piece. Enlarge the star and circle holes for a stronger see-through effect, or change their count for a denser or sparser look. Add a name across the trunk, or add a hanging hole if you want to suspend it.
A small snowflake pin with six branched arms, made to be worn on a shirt. Two loops on the back take a standard safety pin, so the snowflake sits on the fabric like a brooch. Six-arm snowflake with side branches and rounded tips Two back loops, 8 mm apart, for threading a safety pin Flat front face prints directly on the plate No supports needed Roughly 31 mm across and under 6 mm thick
A confident single-word nameplate: a 179 × 64 mm slab, 10 mm thick, with FLOYD rising 3 mm off the face in heavy block capitals for a total height of 13 mm. The letters stretch to roughly 162 × 43 mm, running almost the full length of the top face and leaving only a slim border around them. It reads as signage first and decoration second — the kind of bold lettering that belongs over a door, on a wall, or fixed to a workshop board, and with 10 mm of depth behind it, it also stands on its own as a chunky desk or shelf piece. Sized for a Bambu Lab A1 mini, the sign uses the bed's full width in one direction only, so it prints as one piece with no scaling needed. That width fit is tight: only about 0.5 mm of margin remains on the long side, so a skirt, brim, or calibration offset could push it past the bed edge — a slightly smaller scale is safer if the slicer complains. The 10 mm body uses noticeably more filament than a thin plate, so keep that in mind if material use or weight matters. Design notes Raised lettering sits proud of the plate, catching light and shadow and allowing a contrasting colour with a filament swap at the right layer. The top face, the lettering and the sides are all square-edged; the plate has a flat back and prints from a single flat base without supports. Wide, thick strokes keep the text legible from across a room and sturdy enough to handle. The lettering is proportioned to the plate, so shrinking it uniformly in the slicer keeps the composition intact. Pairs well with a wall bracket, a small stand, or adhesive pads on the back — or just set it down as it is. A plain blue plate with white letters is only one finish — a dark plate with bright lettering, a painted recess, or a single-colour print all work with the same geometry.
Zweiteilige Christbaumkugel, 70 mm Durchmesser, mit durchgeschnittenem Schriftzug "Mari" in der Vorderhälfte. Beide Hälften liegen mit der flachen Seite auf dem Druckbett und passen locker auf das A1 mini. Durchmesser 70 mm, Wandstärke 3 mm Beide Hälften drucken ohne Stützen Stufenfalz zum Zusammenstecken, Kleber oder Klebeband zur Fixierung Aufhängeöse an der Rückhälfte Schrift durchbrochen: Ein Teelicht oder LED scheint durch Die Schrift ist in Pacifico gesetzt. Innere Flächen der Buchstaben (z. B. das a) und der i-Punkt werden als freie Inseln ausgeschnitten.