Flocon — Plateau Apéritif Bonhomme de Neige

Brim — Flat-Bottom Rounded Bowl

Brim is a shallow serving bowl with a flat 75 mm base that sweeps up in a smooth curve to a wide, flat rim. The flat base keeps it stable on a table and easy to print without supports on the bottom face. Dimensions Outer rim diameter: 138 mm Rim width: 5 mm, flat and horizontal Opening inside the rim: 128 mm Depth: 30 mm Flat bottom diameter: 75 mm Wall thickness: 2 mm throughout Print notes Print rim-up or base-down; base-down is the natural orientation. The steepening curve near the rim may need supports or slow cooling.

11 hours agoRemix →

Caneca porta-latas com alça em peça única

Caneca porta-latas em peça única para latas de 269 ml. O corpo cilíndrico tem Ø externo de 64,6 mm e 90 mm de altura, com cavidade reta de Ø 58,6 mm e 87 mm de profundidade útil. A parede tem 3,0 mm e o fundo 3 mm; um furo de Ø 6 mm no centro do fundo alivia o ar, e um chanfro de 1 × 45° na borda interna do topo guia a entrada da lata. Duas faixas salientes de Ø 67,6 mm reforçam o desenho: uma na base, de Z=0 a 10, e outra no topo, de Z=80 a 90, ambas com chanfros de 45°. Entre Z=10 e Z=80 o corpo é liso, para receber adesivo. A alça fica em um dos lados, com 12 mm de largura e avanço até X=54. Ela sobe até Z=80, encostando no início da faixa superior, e mantém topo plano com barra vertical na ponta; a diagonal de 45° fica embaixo. As barras do perfil têm cerca de 6 mm, e as quinas externas e as do furo são chanfradas a 45°. O vão interno acompanha o perfil, com teto em Z=74; o chanfro na quina ajuda a impressão, mas o trecho ainda forma uma ponte e pode pedir suporte. Altura total: 90 mm Pegada na mesa de impressão: 87,8 × 67,6 mm Cavidade: Ø 58,6 mm por 87 mm de profundidade útil Parede de 3,0 mm e fundo de 3 mm Furo de alívio de ar: Ø 6 mm Faixas salientes: Ø 67,6 mm, base de Z=0 a 10 e topo de Z=80 a 90 Alça: 12 mm de largura, até X=54, topo em Z=80, barras de cerca de 6 mm e chanfros de 45° Vão da alça: teto em Z=74, com chanfro na quina; pode pedir suporte sob a ponte

1 day agoRemix →

Sentinel Cylinder Candy Dispenser

A candy dispenser with a watchful streak: the body stands as one straight 105 mm cylinder from foot to rim, and two eye holes on the front give it the look of a sentinel standing guard over the opening below. Those eyes are through-holes opening into a pocket for an ultrasonic sensor, so a wave of the hand can trip the servo below the gate slot and slide the gate open, dropping candy into the hand opening below. That opening is a genuine hole cut clean through the front wall, about 63 mm wide and 21 mm tall, sized for an average hand rather than a large one. A retractable catch tray rides on side rails on its floor, just under the outlet, with a low notch at the front so you can scoop the candy out with your fingers. A cone at the floor of the candy cylinder funnels the sweets down to the outlet, and the whole thing stands 200 mm tall — a tall column that holds a serious load of candy while keeping a modest footprint on the counter. All five pieces are laid out separately on the plate, each oriented for printing without supports. The candy cylinder is silk white, the base pink, the catch tray light blue, and the gate slider and servo horn white. The printed parts Base Housing — a round 105 mm pink body, 48 mm tall. The hand opening sits at the front bottom, open through the wall. The two sensor eye holes sit just above it, also cut clean through, so the sensor has a clear line of sight out the front. The servo bay is sized for an SG90: the servo slides in from the back wall, shaft up, with its mounting ears resting in a slot cut into the housing. A round recess above the body lets the shaft boss sit so the horn runs flush under the gate. The wider body leaves room to open the sensor pocket to full size. Candy Cylinder — a 105 mm open cylinder, 152 mm tall, in silk white, with roughly 3 mm walls, flush with the base so the body reads as one uninterrupted column. A wide, shallow cone at its floor feeds the outlet; everything above it is candy storage. Gate Slider — a flat 26.3 × 33.8 × 2.3 mm white plate that slides sideways in a slot across the outlet, just under the candy cylinder floor. A solid bar covers the outlet when closed; a 12 mm hole lines up when open. Its tail has a slot for the servo horn pin, and about 60° of servo sweep moves the gate roughly 13.6 mm — enough to fully open or close the outlet. Servo Horn — a 10.1 × 13.3 × 3.2 mm white horn with a pin that rides in the gate’s tail slot. The servo below the gate slot turns it to shift the gate. Catch Tray — a 64.5 × 57 × 7.5 mm light-blue tray that slides into the hand opening on two side ribs set in matching grooves, and sits directly under the outlet. Its back and side walls are about 1.5 mm thick, the front wall carries a low scoop notch, and the front edge stands about 1.5 mm proud of the housing as a pull tab. The rails are 3 mm wide with about 0.5 mm clearance in the grooves. There is no end stop, so the tray pulls out completely; a small snap bump would add a stopping point. It prints flat and needs no supports. Before you print The servo pocket matches an SG90: about 12.6 mm wide and 23 mm tall, with a mounting-ear slot. The sensor pocket and eye holes are undersized for an HC-SR04. Open those up while keeping the outside dimensions, or plan on a smaller sensor. The wall between the servo bay and the hand opening is thin, about 0.6 mm at final scale. Print the base with extra perimeters. The 152 mm cylinder is a tall, thin-walled tube — print it upright as laid out, and print it slowly. Check that it fits your printer’s height; if not, split it into two stacking rings. The gate slot has only about 1.4 mm of material above it before the cylinder floor, and the wall between the hand opening and the sensor pocket is thin. Print the base with extra top layers and extra perimeters for strength. Keep the gate plate flat on the bed so it slides cleanly through its slot, and keep the tray flat so its side rails and walls stay square. The base and candy cylinder have no locating lip, so glue or tape them together. Test-fit a real SG90, ultrasonic sensor and tray before final assembly. Wire the sensor and servo to the same controller. When the sensor sees a hand, the controller turns the servo to open the gate, waits, then turns it back to close. Remix hooks — cap the 105 mm cylinder with a lid, open the outlet up for faster dispensing, open the sensor pocket to HC-SR04 size now that the round base has the room, widen the hand opening, deepen the catch tray, add a small snap bump to give the tray a stopping point, or add a shallow funnel lip around the outlet for easier loading.

1 day agoRemix →

Funnel 6 to 2.5 Inch

A one-piece funnel with a 6 in (152.4 mm) inner diameter at the wide end, tapering to a 2.5 in (63.5 mm) inner diameter spout. Each end has a 1 in (25.4 mm) straight wall. Remix hooks Taper length: 60 mm cone section. Lengthen for a gentler slope, shorten for a squat funnel. Wall thickness: 2 mm. Raise to 3 mm for rigidity with heavy contents. Spout diameter: 63.5 mm inner. Change it to match a specific container neck. Pairs with: a mesh strainer disc sitting in the 1 in top collar, or a rubber gasket on the spout. Variants: add a rim lip or hanging tab.

2 days agoRemix →

Stackable 4-Pop Ice Lolly Mold

A 2x2 ice lolly mold that makes four pops at once, with a separate stick for each cavity. Each stick flares into a 45 mm round catch disc, so melting juice lands on the disc instead of running down a child's arm and onto the floor. What it's for Making four ice lollies per fill, with a drip guard built into every stick. Summer use with kids, where sticky hands and floors are the main problem. Stacking several molds in a freezer. A lip on top fits a groove underneath. Dimensions Mold body: 110 x 110 mm footprint, 96 mm tall, plus a 2 mm stacking lip on top. Cavities: 90 mm deep, 30 mm across at the mouth, tapering to a rounded tip with an 8 mm radius. Cavity spacing: 48 mm centre to centre in a 2x2 grid. Sticks: 10 mm wide and 3 mm thick, with a 45 mm disc and a raised rim (about 4 mm tall). Disc: dished, with a 41 mm inner recess to hold drips. Print notes Print the mold body upright, with the cavity openings facing up. Print each stick disc-down so the disc lies flat on the bed. Use food-safe filament and a smooth finish if the mold will touch food. Wash it thoroughly before use. Remix ideas Change the tip radius for a blunter or sharper pop. Make the disc larger for extra-messy flavours. Add a name or initial on each disc to tell kids' pops apart. Change the cavity count to a 1x4 or 3x3 layout.

2 days agoRemix →

Toaster knob.

A replacement knob for a toaster's pull-down lever. The head is 34 × 22 × 16 mm with rounded edges so it sits comfortably under the fingers, and the pin on the back passes through the vertical 6 mm slot in the toaster body to reach the metal lever inside. Knob face to pin tip, the part runs about 42 mm long, and it prints as a single piece with no assembly. The front of the head carries a raised :-) smiley, turned upright and centred, standing 0.8 mm proud of the face. It is made of two 3 mm round eyes, a short vertical nose bar and a curved smile, with the lines drawn thick enough to print cleanly on a 0.4 mm nozzle. Print the knob on its back with the front face up so the relief comes out sharp. The lever slides into a deep slot in the pin and is held by friction rather than by any fastener. Sawtooth ridges along the bottom of the slot let the lever push in easily and resist slipping back out, so the knob stays on through repeated toasting cycles. The slot is deliberately made 0.1 mm narrower than the 1 mm lever, so the fit is snug from the first print: it has to be pressed on, and the slot walls can be filed if it turns out too tight. A loose fit would mean a reprint, so start snug. Print at the stated dimensions rather than scaling, because the friction fit depends on the slot width. Head: 34 × 22 × 16 mm (W × H × D), rounded edges, raised smiley on the front Smiley: 3 mm eyes, 1.6 mm nose bar, 1.8 mm smile, 0.8 mm proud Pin: 5.6 × 10 × 25 mm, centred on the back of the head Lever slot: 0.9 mm wide × 7 mm tall, 22 mm deep measured from the pin tip Teeth: 1 mm sawtooth ridges at 2 mm pitch, starting 10 mm in from the pin tip Fit: 0.1 mm interference on a 1 mm lever — file the slot walls if it binds, never the lever Printing: one piece, no assembly; print on its back with the front face up

3 days agoRemix →

Flocon — Plateau Apéritif Bonhomme de Neige

Dimensions

Pièces et couleurs

Impression

More like this