Industrial Pipe and Fittings
Created 1 months ago
Remixed once
Description
A modular set of pipe fittings featuring a 10-inch straight rod, a perpendicular tee joint, and a straight coupling. Each piece is built around a standard 3/4-inch core diameter with robust 4mm walls to withstand practical shop use.
- 10-Inch Rod: Basic structural member, printed flat for optimal layer strength.
- Tee Joint: Three-way connector with matching bore.
- Straight Coupling: 60mm sleeve for joining lengths end-to-end.
Images
More like this
Explore more in Workshop & Tools →
Industrial Pull Plate
A heavy-duty mounting plate featuring an integrated pull tab and precise counterbored holes. Designed for easy handling and a flush fit with socket head hardware. Mounting Interface: 4x 4.3mm thru-holes with 6.5mm counterbores (4mm deep) Spacing: 72mm x 40mm pattern Convenience: Rounded 35mm pull tab with a 10mm grip hole
12-Inch L-Profile Bracket
A straightforward 90-degree L-profile extrusion, built to a 1.5" × 3" footprint and spanning 12 inches in length. Perfect as stock geometry for building custom brackets, rails, or edge guards. Remix Hooks Thickness: Currently set to a sturdy 1/4" (6.35 mm). This is the most obvious candidate for tweaking if you need a lower profile or a heavy-duty structural piece. Mounting: It's a blank slate. Drop in some counterbored holes along the Y-axis leg if you're mounting it to a wall, or slot it for adjustable brackets. Edge Treatment: The corners are left sharp for flush mounting, but adding a fillet to the inner vertex would strengthen the joint significantly for load-bearing use.
Plate With Offset Square Pad
A flat 28.5 × 40 × 3 mm plate with an 11 × 11 mm raised square pad, 0.5 mm thick, centered in X and set 2 mm from the Y- edge. Remix hooks Pad thickness (0.5 mm): a multiple of your layer height keeps the pad clean. 0.5 mm is about 2 or 3 layers. Pad offset (2 mm from the Y- edge): move it along Y to centre it or push it to the other edge. Plate length (40 mm): the pad is 11 mm, so any length above roughly 15 mm still holds it. Pairs with: a label, a sticker, or a second pad in a different colour for a multi-colour swap.
Flat Ground Plate 45x42x2 mm with Tabs
Flat 45 × 42 × 2 mm ground plate with two side tabs on the front 45 mm edge and two small blocks on the back edge. Overall width across the tabs is 50.4 mm. Plate: 45 × 42 × 2 mm, sharp edges Side tabs: 1.4 mm thick, flush with the underside, 50.4 mm overall span Back blocks: 1.5 mm wide, 1 mm thick, 1.5 mm protrusion, 5 mm from each side edge Print flat, no supports needed
サーボソケット
A servo can't turn a valve knob without a socket that grips it, and a loose fit slips under torque. This cylindrical socket slides onto the knob from the bottom and keeps the top face flat and closed for a future servo horn. Key numbers Body: 30 mm diameter, 14 mm tall, chamfered edges Cavity depth: 10 mm, opening only on the bottom face Opening at the bottom: 2.6 mm × 16.7 mm, widening to 4.5 mm × 16.7 mm at the inner end Clearance: 0.15 mm per side, with rounded corners and slightly bowed long walls Top wall: 4 mm solid, with no screw or mounting holes Printing: open face down on the bed, no supports needed; the wall slope is about 5° from vertical Cavity size, taper, corner radius and clearance are all adjustable parameters
5 x 5 x 1 mm Square Block
A plain square block measuring 5 mm by 5 mm by 1 mm, flat on the bed and ready to print. Remix hooks Footprint: 5 x 5 mm is the starting value. Change it to make a tile, spacer or shim. Thickness: 1 mm is about five layers at 0.2 mm. Raise it for a sturdier piece. Edges: Add a small chamfer or rounding for a softer look. Keep it under 0.5 mm at this size. Pairs with: Use it as a test cube for tolerance checks, or as a base for a hole, text or a peg.