Large Cable Organizer Box
Created 1 months ago
Description
A high-capacity cable management box with a fitted drop-in lid, sized to house bulky power strips, large transformers, and excess cable coils. The rear panel features two mouse-hole style arch cutouts seated flush with the interior floor for easy drop-in cable routing without requiring cables to be threaded through tight slots.
What it's for
- Concealing power strips, power bricks, and cable runs on desktops or floors
- Floor-level cable pass-through that keeps cords flat against the surface
- Dust protection with an easy-access lift-off lid
Dimensions
- Internal Clearance: 215.9 mm (8.5") W × 292.1 mm (11.5") D × 127.0 mm (5.0") H
- Wall Thickness: 3.0 mm
- Port Size: 40 mm wide × 64 mm high arched openings flush to the floor plate
- Outer Footprint: 221.9 mm × 298.1 mm × 133.0 mm (excluding lid hover offset)
Print notes
- Print the box base-down with no supports needed for the arched ports.
- The lid prints flat on its top face for maximum surface quality and bed adhesion.
- Requires a build volume of at least 300 mm × 225 mm.
Images
More like this
Explore more in Storage & Organization →
Open-Top Square Box 75 × 75 × 25 mm
What it's for A plain open-topped square box with a closed floor, sized to hold small parts, tools, or loose odds and ends on a desk or workbench. The straight sides and flat base keep it stable on the print plate and easy to drop things into from above. Dimensions Outer footprint: 75 × 75 mm Height: 25 mm Wall thickness: 3 mm Floor thickness: 3 mm Top: fully open, no lid Print notes Prints upright as it sits, with no supports needed for the vertical walls. A 3 mm wall and floor hold up well in PLA or PETG at a standard layer height; thicker walls take a slightly wider nozzle or more perimeters comfortably. Remix ideas Add a lid or a stacking lip so several boxes can sit on top of one another. Round the outer corners for a softer look and less sharp handling. Divide the interior with a grid to sort small hardware.
Bass Tackle Box With Hinged Lid
Tackle boxes that pop open in the boat, rattle hooks into the soft plastics, or lose a lid hinge get replaced. This one is a hinged bass tackle box with a locking front latch, adjustable dividers and a leaping largemouth bass on the lid, with SMITH FISHING raised underneath. Load-bearing numbers Base: 240 × 160 × 50 mm, 4 mm walls, 3 mm floor, rounded vertical corners. Lid: 240 × 160 × 22 mm, with a raised bass, ripples, waves, hooks and a border on top. Dividers: 5 removable cross dividers, 1.8 mm thick, sliding in 2.4 mm grooves at 38.5 mm spacing. Hinge: 5 interleaved knuckles across the back, joined by a 4.2 mm pin (197 mm long, printed separately). Latches: 2 front latches with 4.2 mm pivot pins. Each hooks under a ledge on the base. Printing Print every piece in the layout shown: base, lid, dividers, latches and pins are all separate. Lid: print upright. The underside of the top plate bridges across the cavity, so use supports or good bridging settings. Layer height 0.2 mm, PETG or ASA, 3+ perimeters. Hinge and latch pins can be glued or capped at the ends to keep them in.
Hexagonal Box with Lid
A hexagonal box with a matching lid, printed as two separate pieces. The box is 50 mm tall and 80 mm across the corners, with 2.4 mm walls and a 3 mm floor. The lid is a 3 mm hexagonal plate with a 6 mm hollow lip underneath. The lip sits inside the box opening with about 0.4 mm of clearance per side, so the lid stays put without a tight press fit. Box: 80 mm across corners, 50 mm tall, chamfered base edge Lid: 80 mm across corners, 3 mm plate, 6 mm inner lip Print the lid flat with the lip facing up No supports needed for either piece
Low-Profile Thread Extractor Tray
A compact drop-in tray for a ten-piece thread extractor set, laid out like a tiny pegboard of hex sockets. Two rows of five hex pockets hold the extractors upright, with a finger slot across each pocket for easy lifting. Design notes Outer size 96 × 42 × 15 mm with 5 mm rounded vertical corners Hex pockets 12.9 mm across the flats, 12 mm deep 3 mm solid floor Sized to sit inside a case or toolbox
Mini 19-Cone Henna Carousel Stand
A compact two-tier henna cone stand: 110 mm trays, 60 mm apart, holding 19 cones tip-down, joined by a 25 mm central column and a screw cap. The top tray's 15 mm holes sit directly over 6 mm tip holes in the lower tray. A foot ring under the lower tray keeps cone tips off the table. Remix hooks Tray spacing: 60 mm now. Raise it for longer cones. Ring layout: 12 holes at 43 mm radius plus 7 at 25 mm radius. Wall between rings is about 3 mm, so adding holes means growing the tray. Tray diameter: 110 mm. Scale it up and add a third ring for more capacity. Hole size: 15 mm top, 6 mm bottom. Adjust to your cone brand. Pairs with: a turntable disc or non-slip mat under the foot ring.
Yu-Gi-Oh Deck Box With Millennium Scale
Two-bay deck box for sleeved Yu-Gi-Oh! cards with a separate accessory bay for dice and other game items. A plug-in lid carries a Millennium Puzzle triangle with an eye and "Yu-Gi-Oh!" lettering in a regular-weight font. Millennium Items are raised on the outside walls. Card bay: 70 mm wide, for sleeved decks Accessory bay: 40 mm wide, with a cross divider separating dice from other items Front: Millennium Scale and Millennium Eye, 1.2 mm raised relief Back: Millennium Ankh and Millennium Ring Sides: Millennium Key (left) and Millennium Rod (right) Lid: flat plate with plugs for both bays, printed plate-side down