Made by CorkWombat
Created 3 days ago
Description
Bu çift, modül 1 mm ve 20° basınç açısıyla birbirine geçen iki evolvent düz dişliden oluşur. Büyük dişli 57 diş, Ø59 mm dış çap ve Ø14 mm mil deliğine sahiptir; küçük dişli 19 diş, Ø21 mm dış çap ve Ø5 mm delikle gelir. İkisinde de diş genişliği 18 mm, eksen mesafesi 38 mm ve oran 3:1'dir. Göbekler güçlendirilmiştir: büyük dişlide Ø28 mm göbek 10 mm yukarı taşar ve radyal M4 set vidası ile somun yuvası taşır; küçük dişlide Ø16 mm göbek 10 mm taşar ve M3 set vidası ile somun yuvası vardır. Her iki göbeğin dişli gövdesine birleştiği yerde konik taban, yükü dişliye yayar.
Set vidası delikleri, göbeğin yüzeyine kadar genişleyen erişim delikleriyle gelir: küçük dişlide Ø7,4 mm, büyük dişlide Ø8,4 mm. Böylece tornavida veya lokma anahtarı vidanın başına doğrudan ulaşır. Somun yuvaları üstten açıktır; somun yana kaydırılarak yerleştirilebilir. Küçük göbekte Ø5 delik çevresindeki duvar erişim deliği nedeniyle incelir; PETG baskıda bu bölgeyi kontrol et.
İki dişli ayrı parçalar olarak yazdırılır. Düzen üzerinde büyük dişli merkezde, küçük dişli 48 mm yanda durur; aralarında yaklaşık 8 mm boşluk vardır, böylece dilimleyicide birbirine yapışmaz. Her parça 28 mm yüksekliğindedir. Tek dişli gerekiyorsa diğerini düzeninden çıkarıp kalan parçayı ayrı yazdırabilirsin.
Atlama ve sıyırmayı azaltmak için dişlerde 0,2 mm diş arası boşluk (backlash) ve 0,3 mm diş dibi payı bırakıldı. Bu değerler basılıp denenmedi; PETG'de çok sıkı gelirse backlash'i 0,3 mm'ye çıkar, çok gevşek gelirse 0,15 mm'ye indir.
Birlikte kullanım için 38 mm merkez mesafeli küçük bir dişli kutusu, düşük torklu motorlu düzenek veya hobi mekanizması için başlangıç çifti olarak düşünülebilir. Farklı oran istiyorsan diş sayılarını ve merkez mesafesini birlikte değiştir.
Images
608 rulman yuvalı, M3 cıvata ve somunla kapanan iki yarım gövdeli, 2 vitesli kayar dişli şanzıman. Giriş milinde 12T ve 24T sabit dişliler, çıkışta 36T+24T kayar dişli kümesi bulunur; 1. vites 3:1, 2. vites 1:1 ve iki çiftte de eksenler arası mesafe 36 mm'dir. Altı parça ayrı basılır ve montaj ister: alt gövde, üst kapak, giriş mili, D profilli çıkış mili, kayar dişli kümesi ve vites kolu. Üst kapağın dış yüzeyinde, kapanmış halde kullanıcıya bakan tarafta 0,8 mm derinliğinde oyulmuş "benze" yazısı vardır. Kapak ters basıldığı için yazı tablaya oturmaz. Gövde iç duvarları hızlı baskı için 1,6 mm'ye inceltilmiştir; rulman yuvaları, cıvata kulakları ve mil uçlarının duvarları 2,4 mm'de kalır. Uyumluluk 608 rulman: 8 mm iç çap, dört adet. Rulman kullanılmazsa basılı kaymalı burç seçeneği vardır. M3 cıvata: yaklaşık 12–16 mm, altı adet; M3 somun altı adet. Mil uçları: giriş ve çıkışta 5 mm D profil veya 5 mm D delik. Dişli standardı: modül 1.5, 20° basınç açısı, düz dişli. Baskı öncesi kontrol Alt gövde ve üst kapak, baskı yerleşiminde yaklaşık 92 × 93 mm taban alanı kaplar; tabla en az bu ölçüyü almalıdır. 608 rulman yuvası 8 mm iç çapa göre çıkar. Rulman yerine basılı burç kullanılacaksa mil çapı aynı ölçüde tutulmalıdır. Gövde iç uzunluğu üç dişli konumu ve kayma payı nedeniyle yaklaşık 60 mm'dir; 36T dişli yüksekliği belirler. Uymadıkları 90 × 50 × 45 mm gövde ölçüsüne sığmaz. Gerçek dış ölçü yaklaşık 92 × 93 × 32 mm'dir. Tek kayar dişliyle 3:1 ve 1:1 aynı eksen mesafesinde elde edilemez; bu modelde kayar küme 24T+36T çift dişlidir. Hazır bir redüktörün yerine doğrudan geçmez; miller, dişliler ve gövde birlikte basılan bağımsız bir düzenektir. Destek malzemesi gerektirmeyecek şekilde düz yüzeyler tablaya gelecek biçimde yerleştirilmiştir. PLA veya PETG ile 0,2 mm katman yüksekliğinde basılabilir; dişliler ve miller için %40–60 dolgu, gövde için %20–30 dolgu yeterlidir.
Gancho de garrafa de treino em J, 200 mm, com braçadeira bipartida na base: corpo fixo ligado à haste e tampa separada que fecha por encaixe de pressão ao redor da alça de 12 × 24 mm. Pontos de remix Snap-fit: ganchos flexíveis de 8 mm de comprimento, 1,8 mm de espessura e ressalto de 0,6 mm (armlen, armt, ridge). Entrada em rampa, retenção reta. Folga: 0,2 mm entre tampa e corpo (gap). Trava extra: furo M3 em gota atravessando tampa e corpo, com porca sextavada embutida no lado +X. Paredes: wallx (6,4 mm) e wallf (7,5 mm) definem o tamanho externo; reduza se o furo M3 for dispensado. Haste e gancho: inalterados, seção 10 × 14 mm, bojo de 40 mm, boca de 34 mm. Combina com: parafuso M3 e porca M3 (opcionais); imprima corpo e tampa separados em PETG ou PLA.

A sleeve that drops into an oversized cup holder and shrinks it, so a slim energy can sits snugly instead of rattling around. Three angled flex fins on the outside wedge the sleeve into holders of different widths. What it's for Sizing down a large truck cup holder for a slim energy can or a standard 500 ml can. Holding the can upright without side-to-side movement. Fitting holders from roughly 80 mm to 95 mm across, using the three flexible fins on the outside. Dimensions Height: 70 mm Body outer diameter: 76 mm Inner bore for the can: 66 mm Base well: 70 mm diameter, 4 mm deep, for the can's bottom rim Drain hole in the base: 20 mm Fins: 3, spaced 120° apart, spanning about 80–95 mm overall, positioned between 14 mm and 56 mm up the body Top edge: small flared lead-in for easy can insertion Print notes PETG works for the whole part. TPU for the fins gives more flex without cracking. Print upright with the base on the bed. No supports are needed for the body. The fins are thin blades, so they bend inward when pushed into a holder. A snug can may need a little extra bore clearance. Fit has not been tested in a real holder, so check your holder's diameter first. Remix ideas Change the bore diameter for other cans or bottles. Add more fins or make them thicker for a firmer grip. Shorten the body for a low-profile holder. Increase the drain hole or add slots to let water escape.
A wall-mounted holder that keeps a 3-ton jack stand and its handle off the garage floor and within reach. The flat vertical back plate carries a U-shaped cradle with a 28 mm bar seat at 65 mm up, the vertical middle of the 130 mm plate. The cradle is open at the top so the bar drops in and lifts out, and open through the middle with a 10 mm wall at each end. The front wall is a 13 mm lip that catches the bar. The cradle walls are rounded at 7 mm on every edge except the one against the back plate, and the inner floor is a 28 mm half-cylinder trough so a round bar lies in it without rocking. The holder prints as one piece. A compact gusset supports the cradle under its full 100 mm width, so the end walls sit flush on it instead of overhanging. Its corners carry the same 7 mm radius, and its underside is an S-curve that leaves the back plate low down, sweeps out, and runs straight up the front of the cradle, meeting both surfaces tangentially so there is no crease where it joins. Keep it around this size; trimming it further leaves little support for a loaded stand. The handle hangs from cuts in the holder rather than being threaded in from the front. The front wall has a 28 mm slit set to the right, centered 24 mm right of centre, open at the top and stopping 12 mm short of the outer edge so the right end wall stays full. The left end wall carries a matching 28 mm U-notch open at the top. The front slit and left notch share the trough floor, bottoming at 51 mm, so a 28 mm handle slides from the trough into them without a step and hangs below. The cradle walls are 55 mm tall and top out at 95 mm, leaving about 16 mm of wall above a 28 mm handle resting at 65 mm. Overall: 100 mm wide, 130 mm tall, 57 mm deep Cradle: U-shaped, 28 mm bar seat at 65 mm up, open top, open through the middle, 10 mm end walls Bar opening: about 80 mm between end walls Front lip: 13 mm thick Handle cuts: 28 mm front slit set right of centre, open at the top and 12 mm inboard of the outer edge; 28 mm U-notch in the left end wall open at the top Floor: trough floor bottoms at 51 mm with the front slit and left notch Cradle walls: 55 mm tall, top at 95 mm, 7 mm rounded edges Gusset: full cradle width, 7 mm rounded corners, S-curve underside tangent to the plate and cradle front Mounting: countersunk screw holes above and below the cradle; use 5 mm or larger screws into a stud or suitable anchor Material: grey PETG; chamfered edges Check that the stand's bar fits the 28 mm seat and the 80 mm opening, and that the handle fits the 28 mm cuts before printing; widen any of them if the real parts are larger.
A knurl-free drive wheel for a pinch-feed wire feeder, built like a small industrial pulley: a 24 mm roller with a hub on one side and a blind D-bore that slips over a 5 mm D-shaft. The model is just the roller, standing on its hub and ready to slice. Design notes Blind D-bore, open on the hub face and closed by a wall on the far end, so the closed end shows which side stays out. M3 grub screw hole with a trapped hex nut that slides in through a slot open to the rim. Counterbored screw recess 2 mm deep, so a headed M3 screw sits below the surface and a nylon or TPU sleeve goes on smooth. Hub spaces the roller off the motor face so the two do not rub. Printing Stands on the hub with the bore opening onto the bed, so there is no bridging inside the bore and no supports are needed. Printing upright keeps the roller round. Suggested: PETG, ASA or nylon, 3 or more walls, 25–30% infill.
A single-arm servo horn for the SG90 micro servo, with a 3.2 mm linkage hole 12 mm from the output shaft centre. Fitment Fits: SG90 and compatible 9 g servos with the 21-tooth, ~4.8 mm output spline. Does not fit: MG90S metal-gear servos with a different spline count, or 25T servos such as MG995/MG996. Arm: 12 mm centre distance, 4 mm thick, rounded edges. Check before printing Test the spline bore on a scrap print. Bore size is ~4.9 mm with small tooth notches, and printer tolerance varies. Adjust it if the fit is loose or tight. The part prints flat with no supports, and PLA works.