Monolithic Mirrored Roof Bridge
Created today
Description
A custom monolithic spanning piece built for standard interconnecting block systems. It features two continuous 26-stud curved roof sections (matching a 15068 profile) separated by a sunken two-stud central channel.
- The central channel is dropped by one standard plate height (3.2 mm), allowing the next layer of parts to sit flush below the curve peaks.
- The underside features a full 6x26 cavity equipped with 125 interlocking tubes.
- Integrated structural cross-ribs connect the entire undercarriage, providing genuine rigidity and ensuring a tight clutch across a massive 208 mm span.
Images
More like this
Explore more in Automotive, RC & Hobby →
Monolithic Mirrored Roof Bridge
A custom monolithic spanning piece built for standard interconnecting block systems. It features two continuous 26-stud curved roof sections (matching a 15068 profile) separated by a sunken two-stud central channel. The central channel is dropped by one standard plate height (3.2 mm), allowing the next layer of parts to sit flush below the curve peaks. The underside features a full 6x26 cavity equipped with 125 interlocking tubes. Integrated structural cross-ribs connect the entire undercarriage, providing genuine rigidity and ensuring a tight clutch across a massive 208 mm span.
Motorcycle Script Logo Plate
A vintage-style brand badge featuring raised script typography and an under-swoosh, framed by a continuous outer rim. Designed to resemble classic cruiser motorcycle tank badges and dealership signage. Features: Dimensions: 110 mm wide by 50 mm tall. Profile: 3 mm solid base plate with 2 mm raised lettering and rim. Typography: Stylized cursive script reminiscent of early 20th-century automotive branding. Printability: Flat back for easy bed adhesion; raised details are optimized for standard filament swaps at the 3 mm mark.
Nimbus — 100mm Quad Frame
A scaled-up quadcopter frame designed for 7mm coreless motors. Originally modeled for a compact layout, the arms are now extended to give a full 100x100mm outer footprint while retaining the 25.5mm whoop flight controller mounting pattern. Features Friction-fit Mounts: Sized for 7mm brushed motors, with an integrated wire routing slit. Underslung Tray: Integrated bottom mount for a standard 1S battery. Lightweight Arms: Hull-cut arm profiles that parametrically scaled up to span the new 100mm stance without adding unnecessary mass.
15mm Shaft 900-Degree Stopper
A compact, print-in-place traveling nut mechanism designed to mount onto a 15mm diameter shaft. This stopper locks rotation exactly at 900 degrees (2.5 turns) in either direction. The inner blue sleeve slides over your 15mm shaft and secures with a standard M3 bolt and captive nut, while the outer orange traveler moves up and down the internal threads as the wheel turns. Fitment and Constraints Host Shaft: 15mm diameter. The bore is modeled at 15.2mm to allow for a snug fit. Rotation Limit: Exactly 900 degrees (2.5 turns), enforced by rigid top and bottom flanges. Assembly: Print-in-place. The mechanism prints fully assembled with 0.4mm radial clearance in the threads, permanently capturing the traveler nut between the outer flanges so it cannot back off. Installation Requirements: You must have a fixed block or housing wall nearby for the traveler nut's side tab to ride against; this prevents the nut from simply spinning with the shaft and forces it to travel linearly.
12mm Hex Parade Truck Wheel
A 70x25 mm solid front wheel designed to mate with a standard 12 mm RC hex drive. Built as a single rugged piece, it combines a deep-block tire tread with a solid structural hub to handle the weight of larger FDM parade and display builds. Fitment Specs Drive Interface: 12 mm standard RC hex (6 mm deep pocket) Axle Bore: 5.2 mm clearance hole Outer Dimensions: 70 mm OD × 25 mm width Printing: Flat on the hex face, no supports required.
CycMount — Toolless Camera Clamp
Introducing CycMount, a robust camera mount engineered to secure action cameras to standard 22mm bicycle handlebars. Built with frequent swaps in mind, it utilizes custom wing nuts for a completely tool-free installation, allowing quick transfers between bikes. The integrated three-prong interface is precisely dimensioned with 3mm thick fingers on a 5mm pitch, ready to accept standard action camera housings and a 5mm pivot bolt. Design Features Strength by Orientation: Both clamp halves print flat on their sides, aligning the layer lines perpendicularly to the clamping stress for maximum strength. Support-Free: The horizontal print orientation ensures the 22mm handlebar bore and the 5.2mm pivot hole print perfectly round without requiring slicer supports. Tool-Free Adjustments: Includes two custom wing nuts designed with integrated M5 hex nut traps. Required Hardware 3× M5 Hex Nuts (two for the wing nuts, one for the bottom clamp) 2× M5 Cap Head Bolts (for the main clamp body) 1× M5 Bolt (for the camera pivot)