Nit ring v3.2 (7.4mm)
Created 1 months ago
Description
What it's for
A custom two-stage spacer or bushing. The bottom section flares out for a wider footprint, while the top maintains a straight profile. A continuous through-hole runs the entire length, with a shallow counterbore at the base to recess a bolt head or capture a mating pin.
Dimensions
- Total Height: 12.5 mm
- Tapered Base: 9 mm diameter at the bottom, flaring to 13 mm over a 3 mm height.
- Straight Collar: 9 mm diameter, 9.5 mm high.
- Bore: 7 mm clearance hole straight through.
- Counterbore: 9 mm diameter, recessed 2 mm into the bottom.
Print notes
Print this sitting flat on its wide base. The counterbore is shallow enough that most standard profiles will bridge it without requiring supports.
Images
More like this
Explore more in Workshop & Tools →
O-Ring — Solid Spacer
A heavy-duty cylindrical ring, measuring exactly 115mm across with a 65mm bore. Built straight and solid, ready to act as a substantial standoff, collar, or structural spacer. Dimensions Outer Diameter: 115 mm Inner Diameter: 65 mm Height: 30 mm Wall Thickness: 25 mm
T-Shaped Mounting Blocks
A pair of 40mm tall, T-shaped mounting blocks designed to bolt flush against flat surfaces. Both versions feature 4.5mm clearance holes with deep 45-degree countersinks sized for 9mm screw heads. Two-Hole Block: Dual mounting points vertically spaced at 10mm and 30mm for rigid anti-rotation fixing. One-Hole Block: Single central mounting point at 20mm height. Dimensions: 20x20mm main body with a 5x30mm mounting flange. Tolerances: 2mm corner rounding on all vertical edges to relieve stress and ease printing.
dimensions test plate
A specialized, low-profile custom plate designed to tight dimensional constraints. Measuring exactly 1mm thick, it provides a precise mounting or spacing surface with asymmetrical bore sizes. Specifications: Dimensions: 50mm length, 25mm width, 1mm thickness. Primary Bore: 18.5mm diameter. Secondary Bore: 16.5mm diameter. Clearances: Exactly 5mm of material left between the outer edges and the bores, as well as between the bores themselves.
Hoof Evener Thumb Ring
A low-profile thumb ring designed to friction-fit onto the center support of a hoof-evener ruler. The ring is split to flex over a variety of thumb sizes while keeping the geometric center locked perfectly inline with the measurement zero-point. Remix Hooks Thumb clearance: Currently set to an inner diameter of 22mm. The 5mm split opening allows for expansion, but the base diameter is the first thing to dial in for a specific hand. Strut channel: The rear mounting slot is sized for a 12.5mm × 4.5mm vertical support. Adjust this block to match the actual sheet metal or printed strut of the evener. Locking hole: A 3.3mm pilot hole runs through the back wall. Drive an M4 set screw or short bolt through it if the friction fit over the strut needs extra bite.
fence conector
A minimalist, heavy-duty H-profile block. Designed with tight inner clearances and thick outer walls, this spacer is ideal for slotting over rails or serving as a sturdy structural bracket. Dimensions Overall Size: 36mm wide × 50mm deep × 40mm high. Inner Channel: 16mm gap width. Wall Thickness: Solid 10mm posts on either side. Print Notes Prints cleanly on its back or base without supports. The 3mm edge rounding improves handling and prevents stress concentrations at the corners.
4mm Square Key & Mount
The 4mm square key is the thing you can never find when a radiator needs bleeding or a panel needs opening. This gives the key a dedicated wall mount so it actually stays put. Includes a fitted bracket and custom printed M4 screws that use the same 4mm square drive as the key itself — meaning you don't even need a separate screwdriver to mount the bracket. Mounting bracket: 55mm × 15mm Key shaft: 4mm square Screw drive: 4.5mm square recess