Numbered SD Card Organizer Tray
Created 1 months ago
Description
Memory cards scatter across desks and get mixed up between cameras the moment you set them down. This flat organizer tray pins down eight standard SD cards and eight microSD cards in numbered slots, mapping exactly which card belongs to which camera body. Deep semicircular thumb scoops break the flush fit, letting you tilt a card out immediately instead of prying at the edges with a fingernail.
Slot Fitment
- Standard SD: 33 x 25 mm footprint, 2.5 mm deep.
- MicroSD: 12 x 16 mm footprint, 1.5 mm deep.
- Print settings: Print flat on the bed. No supports required. The embossed numbers sit 0.6 mm high, resolving cleanly at a standard 0.2 mm layer height.
Images
More like this
Explore more in Desk & Tech →
Pi 3 case
A bare Raspberry Pi 3 is so light that hooking up a standard HDMI cable instantly tips it off the desk. This case locks the board into a heavy enclosure and uses snap-on outer corner bumpers to give it some actual grip, so the board stays exactly where you put it. The port cutouts are oversized enough to accept real molded cables without them binding against the shell. Bed Fit: Everything is packed tightly to fit in a single run on a 180×180 mm print bed. Printing: All pieces sit flat on the plate. No supports required anywhere. Clearances: Built with a 0.4 mm gap around the board and lid joint so it slots together cleanly.
A-Frame Mobile Stand
A sturdy, functional stand for phones and small tablets. Designed with a 35-degree viewing angle, it works nicely for watching media or keeping an eye on notifications while at your desk. Features a 16mm-wide cutout for routing charging cables Includes a solid rear spine to prevent flexing when tapping the screen 14mm resting gap accommodates most phones, even with a case Prints in one piece without supports
Assistive Smart Goggles Chassis
What it's for A wearable housing for smart glasses components, scaled to fit a human head. Features isolated electronic cavities, hollow arms for speakers and haptics, and integrated ports for front-facing cameras and downward sensors. Dimensions Overall Width: 150 mm Lens Housings: 52 mm tall, 18 mm deep Temple Arms: 11 mm wide, with a 30-degree drop behind the ear Assembly The frame and two arms print as separate flat-laid components without supports. Hinge tabs are modeled in — use short 3 mm pins or filament offcuts to join them.
355ml Can Tray & Angled Desk Stand
Two-piece modular desk platform with a precision-fit dovetail seam. The main tray spans 250x160mm and runs four custom 68mm bores—sized specifically to drop in 355ml soda cans with exactly 1mm of clearance so they never bind. The extension plate mates flush to the right edge via four full-depth dogbone locks. It carries over the four cable passthrough notches and builds into an 89mm-tall backing plate offset precisely to set up a 15-degree resting angle off the main tray's front partition. Built with squared alignment edges against the seam and a solid side-stop block to lock your gear into place. Critical Dimensions Host Standard: 355ml standard soda can (66mm body). Overall Footprint: 500mm wide by 160mm deep (assembled). Seam Clearance: Locks are cut with 0.25mm of total gap so they seat tight without filing.
Grid Tray And Puzzle Blocks
A flat 90x90mm tray with an 8x8 internal grid and a matching set of puzzle blocks. Tray: 90x90mm outer dimensions, 10mm high, 2mm walls and base, with 0.5mm deep grid lines separating it into 64 fields. Blocks: Assorted flat 2.5mm thick puzzle shapes (T, L, Square, S, Long-3, Long-2, Dot, 6-Block) sized to fit the grid with 0.5mm clearance. Each block features a single vertical tab on one edge for easy placement and removal.
Retro TV Enclosure v2
A reinforced retro TV enclosure designed for an RP2040 video player project. The walls have been bulked up for extra durability without compromising the interior payload space, while side-firing one-inch speaker grilles and a classic bent antenna give it a finished look. What it's for Built to house a no-solder RP2040 media player. The clamshell locks together with an integrated friction fit and the entire model prints flat on the bed with zero supports. Dimensions Internal volume: 150 × 80 × 50 mm Wall thickness: 5 mm (beefed up from standard) Grilles: 25.4 mm (1 inch) perforated arrays on the left and right panels Assembly Both halves print cleanly flat. Slide your display into the front bezel's chamfered recess, route the cables out the back USB port, and firmly press the halves together until the interior ridges lock.