Made by TangentPantograph
Created today
Description
Tromba Perch è una coppia di staffe laterali indipendenti per una tromba 220x160 mm con interasse fori di 240 mm. Senza traversa centrale, ogni staffa si avvita sul monitor con la propria base e regge un lato della tromba. Si risparmia materiale e ogni pezzo entra facilmente nel piatto di stampa.
Images

A fan-shroud adapter in the spirit of a classic blower nozzle: a flat square flange that funnels up into a round outlet, then runs straight like a spout. 92.5 mm square flange, 4 mm thick, with four M3 clearance holes on an 82.5 mm pitch (5 mm from each edge) 75 mm square inlet 50 mm square-to-round transition 30 mm straight round tube, 32 mm inner diameter, 36 mm outer 2 mm walls, no chamfers, prints flange-down in PLA without supports
What it's for A minimalist desk organizer with four open-top compartments for pens, pencils, markers and small stationery. A stepped front lowers the front pair for easy reach to small items, and a small NEXUS logo is engraved on the front face. Dimensions Footprint: 120 × 80 mm Height: 95 mm rear, 60 mm front Wall thickness: about 2.4 mm Flat base, rounded vertical corners, chamfered base edge Remix ideas Change the logo text to a name or initials. Make the front compartments deeper for scissors or rulers. Add a non-slip pad under the base.
A phone stand for a phone that keeps sliding flat or tipping over: a 60° backrest holds it upright, and a front lip stops it sliding out. Key numbers Base: 100 × 60 mm, 2.2 mm thick Backrest tilt: 60° from the table Slot: 12 mm wide, measured between backrest and front lip Walls: 2.2 mm throughout Corners: rounded in plan and along the profile edges Printing Print with the base flat on the bed. No supports needed: the backrest leans back at 60°, which stays within a typical overhang limit. Phones with thick cases may need a wider slot.
A dual-joystick controller enclosure that can't be wired or soldered through the top, because the two 52 × 52 mm joystick openings are too small for the board. This version splits the floor off as a removable bottom cover, so the board and joysticks go in from below. Key numbers Outer size when assembled: 165 × 105 × 35 mm (shell 33 mm + cover 2 mm) Walls and top panel: 2 mm; corner radius R6 Joystick openings: two at 52 × 52 mm, R3 corners, 14 mm apart RJ45 window: 25 × 18 mm, centred on the rear wall, 6 mm up from the open edge (provisional) Cover lip: 0.3 mm clearance inside the walls, 3 mm tall Printing Shell: print top panel down, open side up, no supports. Cover: print flat with the lip pointing up. Check the 25 mm bridge over the RJ45 window in the slicer preview. The cover is held by friction or a dab of adhesive; there are no screws.

Liftoff is a pair of riser feet that shim the rear clip of a monitor light bar upward, so a bar that tilts down toward the user can sit level and aim at the desk instead of the eyes. Each foot is a flat 30 × 20 mm platform that lifts the clip 8 mm, with a short lip on the front edge that hooks over the top of a thick-bezel monitor and keeps the foot from sliding around. A flat top was chosen over a sloped wedge: it raises the whole clip evenly, and the lip handles the positioning. Dimensions Platform: 30 × 20 mm, 8 mm thick (clip lift) Hook lip: 2.5 mm thick, 12 mm drop below the platform Overall height per foot: 20 mm Quantity: 2 identical feet, spaced 10 mm apart in the layout Features Front lip locates the foot on the monitor's top edge Chamfered top edges on the sides and back for a cleaner clip seat Chamfered lower lip edge for easier hooking Print notes Print with the platform's flat back or side on the bed, or upright with the lip facing down, depending on the preferred strength direction The 12 mm lip drop is a starting value; adjust it to match the actual bezel thickness PETG or ABS is a good choice if the monitor top gets warm
Funda rígida diseñada específicamente para las dimensiones del Samsung Galaxy A20e (147,4 × 69,5 × 8,3 mm), incorporando márgenes de tolerancia estructurales para facilitar la inserción del dispositivo. La cara trasera presenta el nombre "Pablo" integrado en relieve volumétrico sólido, utilizando la fuente seleccionada para maximizar la resistencia de las letras. Material recomendado: PLA, PETG o TPU (dependiendo de la flexibilidad deseada). Relieve de texto: 1,5 mm, extruido hacia el exterior. Tolerancias: +0,6 mm en ejes X e Y para un acople por fricción sin forzar la estructura. Perforaciones: Cámara principal dual, lector de huellas dactilares trasero, botonera lateral completa y acceso inferior (USB-C/Audio/Altavoz).