Obsidian — Ribbed Can Cooler with Handle
Created yesterday
Description
Obsidian is a matte-black-ready can cooler for standard 330 ml cans, with a reinforced side handle, diagonal grip ribs and a flat front panel reserved for names or logos. The handle opening has a peaked top so it prints upright without supports.
Dimensions
- Inside diameter: 68 mm
- Inside height: 105 mm (above a 3 mm base)
- Wall: 2 mm, base: 3 mm
- Overall height: 108 mm; footprint about 115 × 74 mm including handle and panel
Features
- Diagonal ribs outside, perfectly smooth bore inside
- Rounded top rim
- Broad, rounded handle, 24 mm wide
- Flat front panel, 40 × 66 mm
Print notes
- Print upright, base on the plate, PETG, 0.4 mm nozzle, 0.2 mm layers
- No supports expected; fits a 180 mm build volume
Photos
Technical views
More like this
Explore more in Kitchen & Bathroom →
Galaxy Cap & Pets
A standalone pop-top can cover designed for easy swapping of customizable 3D-printable pets. Hooks for Remixing The Peg System: The mounting peg on the cap is a standard 3.8 mm cylinder, sitting slightly toward the back edge. Any custom object with a matching 4.2 mm socket will drop right on. Skull Profile: The flat skull on the cap is an exact scaled-down copy of the original 3D geometry. Expansion: Want to add more utility? You could stretch the cap base horizontally to house three or four pets simultaneously, or angle the peg so the figure faces upward when the can is open.
Round Water Bottle With Cap
A round water bottle with a tapered shoulder, a 24 mm mouth and a separate slip-on cap. Printed as a hollow vessel with 3 mm walls. Remix hooks Body diameter and height: 70 mm wide, 170 mm straight section. Change these to resize capacity. Wall thickness: 3 mm. Raise it for watertight prints in PLA, or lower it with vase mode in mind. Neck: 24 mm bore, 30 mm outside. Swap the plain cap for a threaded one using a threaded rod and nut. Pairs with: a silicone gasket, a carry loop through the neck ring, or a sleeve that fits the 70 mm body. The cap is a friction fit and not a sealed closure. Test before filling.
Sink Caddy With Drain Slots
Sponges and brushes left in a flat tray sit in a puddle and go sour. This sink caddy lifts them on ribs over a slotted floor so water runs out, and a separate tall holder takes a brush upright. Key numbers Tray: 200 x 110 x 45 mm, 2.4 mm walls Floor: 2.5 mm with 9 drain slots, plus 4 mm ribs to keep items off the surface Front notch: 60 mm wide, lets water pour off the front edge Brush socket: 48 mm square, inner opening 44 mm Removable holder: 40 x 40 x 100 mm with side slots for drainage; 2 mm clearance in the socket Printing Print the tray flat, no supports Print the holder upright 0.2 mm layers, PETG suggested for wet use
HexCatch — Geometric Coaster
Introducing HexCatch, a 90mm circular coaster engineered to keep surfaces perfectly dry. The surface features a recessed, concentric hexagon pattern that acts as a condensation trap, drawing moisture away from the base of glassware before it can pool and run onto the table. \n\n## Dimensions\n Overall footprint: 90mm diameter\n Thickness: 5mm \n Channels: 2mm wide and 1mm deep\n\n## Features\n Integrated drip reservoir: Geometric recesses hold condensation safely off the table.\n Modern profile: A clean circular exterior contrasts with the sharp hexagonal interior.\n Chamfered base: Slight angle on the bottom edge makes it easy to lift from flat surfaces.
Weihnachtliche 3-Etagen Etagere
3-Etagen Steck-Etagere im weihnachtlichen Stil. Konzipiert für den separaten Druck. Teller: 160 mm, 120 mm und 80 mm Durchmesser, jeweils mit erhöhtem Rand (2,5 mm tief) und dezentem Rillenprofil (1,5 mm Profiltiefe). Säulen: 80 mm hoch, mit integrierten Zierkugeln im Abstand. Stecksystem: 11,5 mm Zapfen auf 12,0 mm Loch für spielfreie Montage. Topper: 5-zackiger Stern als Abschlussstecker.
GlideTrak — Under-Shelf Stemware Rack
GlideTrak is an under-shelf stemware storage block designed to securely hold up to four standard wine glasses upside down by their stems. The dual-channel architecture features a continuous track that flares wide at the opening, allowing smooth, one-handed retrieval and stowing of glasses without requiring precise visual alignment. Engineered as a robust mounting block, it secures flush against the underside of a cabinet while maintaining a clean profile. Features Flared Entry: The stem slot narrows from a 14 mm flared opening down to a 9 mm continuous track, guiding standard stems seamlessly into place. Concealed Mounting: Six countersunk holes with screwdriver access tunnels provide secure upward mounting, hiding the screw heads deep within the block. Support-Free Printing: Engineered to be printed standing vertically on its flat back wall, allowing the internal cavities to form cleanly without the need for support material. Dimensions Overall Footprint: 212 mm wide × 170 mm deep × 22 mm thick. Base Clearance: 82 mm wide internal cavity per channel to accommodate standard glass bases. Stem Track: 9 mm track width, expanding to a 14 mm flare at the front entry.