Made by a Guest
Created yesterday
Description
A three-tier spice rack that holds 12 jars, four per tier, with each tier stepping up so every label stays in view without lifting a jar out. Each pocket is sized for jars about 40 mm across, so the rack is easy to scan for cumin or anything else.
The rack measures 180 mm wide, 150 mm deep and 66 mm tall at the back. Tier heights are 26 mm (front), 46 mm (middle) and 66 mm (back). Each tier is 50 mm deep and 20 mm taller than the one in front. Each jar sits in a 42 mm round pocket, 3 mm deep, which stops it sliding forward. The edges carry a 1 mm chamfer. It prints as one piece, and the three tiers are shown in separate colours so they are easy to tell apart.
Images
A four-level spice rack for 20 jars, five per shelf, with no back panel to save filament. Each shelf is its own tray with smooth lens-shaped oval sides and a front lip carrying raised spoons and forks. Round connector posts with small pegs join the shelves and pull apart. Remix hooks Slot width (52 mm): change for larger or smaller jars; overall width follows. Level pitch (85 mm): raise for tall jars, which also lengthens the connector posts. Shelf count: set to 2–6 levels for a different stack. Side shape: oval height 76 mm and depth 60 mm; scale the oval for a rounder or flatter profile. Peg fit: pegs are 6 mm with 0.2 mm clearance per side; tune for your printer. Variants: swap the cutlery for other icons, or add wall-mount holes in the shelf floor. Overall size is about 266 × 60 × 325 mm. Print shelves flat and posts upright. Pairs well with a wall strap or a non-slip mat.

A two-tier spice rack that mounts on the inside of a cabinet door. A flat back plate carries two shelf tiers that project forward, so jars ride on the door rather than on the cabinet shelves and the door can close over them. The upper tier sits 137 mm above the lower shelf, leaving enough height for 105 mm spice jars on the bottom shelf with roughly 14 mm of finger room once a jar is lifted over the 14 mm front lip. Specs Overall size: 175 mm wide, about 174 mm tall, 55 mm deep. Fits an 18 cm print bed. Tiers: two, set 137 mm apart. The top tier ends about 155 mm up the plate. Jar fit: each tier holds jars around 48 mm across. A 14 mm front lip and end walls keep jars in place as the door swings. Door clearance: the tiers project 55 mm from the door. Check the gap between the closed door and the cabinet shelves before printing; hinges and shelf edges can reduce it. Mounting: four countersunk 4.5 mm screw holes through the back plate, with the upper holes at 163 mm up the plate and 12 mm of plate above them. The countersink suits M3.5/#6 flat-head screws; check screw length against the door thickness so they do not break through the front face. Print orientation: back plate down with the shelves growing upward, so no supports are needed. Measure the door-to-shelf clearance and jar diameter before committing to a full print; the depth and tier spacing depend on both.

Picking kale, chard or rosemary leaves off the stem by hand is slow, and one hole size never fits both a fat kale rib and a thin rosemary sprig. This herb stripper paddle has seven holes graduated from 12 mm down to 3 mm, so you pick the hole that grips the stem and pull the stem through. The leaves catch on the edge and come off. Each hole has a small flare on the top face so the stem starts in without catching. A hang hole at the end lets the paddle sit on a hook next to the board. Key numbers Paddle: 150 mm long, 40 mm wide, 6 mm thick Stripping holes: 12, 10.5, 9, 7.5, 6, 4.5 and 3 mm, spaced 16.5 mm apart, big to small Hang hole: 10 mm, 12 mm in from the end Corners: 4 mm radius on the flat outline Printing Print flat, with the flared side facing up No supports needed Food-safe filament such as PETG is the usual pick, and a wash by hand is best Use 3 or more perimeters so the thin edges around the holes stay stiff
A one-piece funnel with a 6 in (152.4 mm) inner diameter at the wide end, tapering to a 2.5 in (63.5 mm) inner diameter spout. Each end has a 1 in (25.4 mm) straight wall. Remix hooks Taper length: 60 mm cone section. Lengthen for a gentler slope, shorten for a squat funnel. Wall thickness: 2 mm. Raise to 3 mm for rigidity with heavy contents. Spout diameter: 63.5 mm inner. Change it to match a specific container neck. Pairs with: a mesh strainer disc sitting in the 1 in top collar, or a rubber gasket on the spout. Variants: add a rim lip or hanging tab.
A blocky sleeve that drops over a T-post and carries a flat square platform on top — a brutalist plinth silhouette in cap form, all hard edges and stacked planes. The pocket inside is T-shaped, cut generously around a typical steel fence T-post: a 38 × 7 mm flange opening and a 7 × 38 mm stem slot, leaving roughly a millimetre of play per side so it drops on without a fight. The sleeve is 40 mm deep with 3 mm walls and a 4 mm roof, and the whole cap stands 46 mm tall over a 60 × 60 × 6 mm platform. Design notes T-shaped pocket for a T-post — flange opening 38 × 7 mm, stem slot 7 × 38 mm. Pocket sized with a little slack per side; the 7 mm slot width is the fit-critical dimension on real posts. 40 mm deep sleeve, 3 mm walls, 4 mm roof. 60 × 60 × 6 mm square platform sits on top as one solid piece with the sleeve. Overall footprint on the print plate: 60 × 60 mm, 46 mm tall. Prints as a single part; no assembly and no fasteners. Good to know The pocket is shaped from a typical steel fence T-post rather than a measured one — check your post's flange width, stem length and metal thickness before committing to a long print. Platform size is independent of the pocket, so it can grow or thicken without touching the post fit. Tightening or loosening the pocket is a small change if the cap ends up sloppy or stubborn on the post. The sleeve's outside was widened to 44 mm to keep the walls at a full 3 mm around the bigger pocket, so the cap stays chunky rather than thin-shouldered.
A five-point star cookie cutter, 60 mm tip to tip, with 18 mm tall walls and a wide flat flange around the top edge. The flange gives a thumb a broad surface to press on, so pushing the cutter through dough doesn't put a thin edge against your skin. Remix hooks The values below are the ones worth changing. Everything else follows from them. Star size (R, 30 mm): This is the tip radius, so 60 mm across. Change it to scale the star. At about 40 mm across or less, check that the flange doesn't crowd the inner corners. Point sharpness (ratio, 0.5): This is the inner radius divided by the outer radius. Lower values like 0.4 give spikier points. Higher values like 0.6 give a chubbier, more rounded star. Very spiky points are harder to press out of dough. Flange (flangew 4 mm, flanget 2 mm): Widen it for a more comfortable press, or thicken it for more stiffness. Rounding the flange's outer corners is an easy variant if you want it softer on the thumb. Wall (wall, 1.2 mm): This is about three nozzle widths on a 0.4 mm nozzle. Thinner cuts more cleanly but is more fragile. Thicker is sturdier but pushes dough aside more. Height (H, 18 mm): Lower it for thin cookies, or raise it for thick dough or a deeper grip. Pairs well with A set of different sizes, made by changing R and nothing else. Other shapes that reuse the same wall and flange values, such as a heart or circle, so the whole set feels the same in the hand. A matching stamp or embossing plate that fits inside the cutter opening. Printing Print it flange-up or flange-down on the bed. Flange-down needs no supports, and the thin walls grow straight up from the flange. Use food-safe filament if you want to use it on dough.