Noelring — Christmas Lettering Ring for a 97.4 mm Sphere
Created today
Description
Noelring is a seating ring designed to sit inside a hollow sphere, with “Merry Christmas 2026” lettering held in its opening. The ring’s outer edge is cut to the sphere’s inner curve, so the seat meets a 97.4 mm internal-diameter shell across the full 3 mm ring width instead of resting on a single line. The top and bottom faces are flat, the centre is open with no background plate, and the three text lines run the full 4 mm height of the ring, flush with both faces. The lettering is set in Parisienne, a connected cursive script with a dotless “i” in “Christmas”; “Christmas” runs into the ring wall at both ends and is the only line fused to it, while “Merry” and “2026” are not tied to the ring and depend on touching “Christmas” to stay in place.
Dimensions
- Ring: 97.4 mm outer diameter × 4 mm tall
- Ring width: 3 mm; inner diameter about 91.4 mm
- Seat: outer edge curved to a sphere with a 97.4 mm internal diameter (48.7 mm radius)
- Lettering block: about 91.3 × 48.2 mm, full 4 mm height
Features
- Curved outer edge follows the sphere’s inner surface across the full ring width
- Flat top and bottom faces, with the seat carried on the outside edge
- Open centre: the lettering has no background plate behind it
- Three stacked lines, “Merry”, “Christmas” and “2026”, set in Parisienne, a connected cursive script
- “Christmas” runs into the ring wall at both ends and is anchored there
- “Merry” and “2026” are not joined to the ring; they rely on contact with “Christmas”
- The “i” in “Christmas” is dotless, so the line has no separate dot
- All three lines are set flush with the ring’s top and bottom faces
Fit
- Made for a hollow shell with a 97.4 mm inner diameter; scale the ring and sphere together for any other size
- The 4 mm height is a design choice: a taller ring grips more wall but reaches further into the sphere
- The ring locates itself against the sphere’s curve rather than locking in place
Print notes
- “Christmas” is fused to the ring at its ends; “Merry” and “2026” are held only where they touch “Christmas” — check those contact points before printing
- If a word does not touch “Christmas”, it will print as a loose piece
- No struts connect “Merry” or “2026” to the ring wall
- No supports should be needed for the flat ring and full-height lettering
Images
More like this
Explore more in Decor & Display →
Chubby Baby Dragon Figurine
A cute chubby yellow baby dragon with a big round head, cream oval belly, green eyes, short limbs, a tiny tail and small horns. About 80 mm tall with a flat base, built as one welded body. Remix hooks Head size: the head is a 48 mm sphere; enlarge it for a more chibi look, but keep the body wide enough to support it. Eyes: 10 mm ovals; push them outward or scale them up for a different expression. Belly: a flattened ellipsoid at the front; swap its colour for multi-colour printing. Pairs with: a round display plinth, or a keychain loop on the horns. Limbs and tail: short ellipsoids, easy to lengthen if you want a more dynamic pose.
Single Faced Baby Cube with Number
Unit is a plain 30 mm cube with one decorated face: a raised border frame and a bold raised "1" centred inside it. The other five faces stay flat, so it sits and stacks cleanly. Features 30 mm cube, flat base on the build plate Raised border, 2.5 mm wide and 1.5 mm high Raised "1" centred on the front face Decoration on one side only Print notes Print with the decorated face pointing toward the side or use supports-free orientation with the face up for the crispest numeral. Two colours can be swapped in at the 30 mm layer for a contrasting border and numeral.
Newar Lantern — Pagoda Temple Lamp
The Newar Lantern is a miniature Newari-style Hindu pagoda temple built as a display lamp, standing 250 mm tall with a roof that overhangs a narrower temple body. The chamber inside is hollow and open at the front, with a 60 mm opening in the ceiling that drops LED light onto a separate Ganesh statue, while the cable runs in a ceiling channel, down a rear groove and out an 8 mm exit at floor level so the wiring stays out of sight. The three roof tiers lift straight off for access to the light and statue, and every piece sits on a flat bottom for stable printing. Dimensions Assembled height: 250 mm Lower roof: 200 × 180 mm; base: 155 × 145 mm Internal chamber: 112 × 92 × 115 mm with a flat floor Arched front entrance: 105 × 105 mm, open at the front Ceiling light opening: 60 mm, with a recess for the LED holder Finial spigot: 12 mm Features Three progressively smaller roof tiers with uppturned corner horns, layered eaves and a small windowed storey beneath the lower two A pointed finial seated in the top roof on a 12 mm spigot Two-step platform base with a row of 6 mm spherical ornaments Arched entrance with a framed, studded border, corner pillars, lattice side windows and a cornice LED holder: a flat plate with a collar for the module and a cable slot Separate seated Ganesh statue on a flat pedestal, about 90 mm tall and sized for the chamber Print notes Seven pieces: temple body, three roof tiers, finial, LED holder and Ganesh statue Roof tiers join on 5 mm pins and 5.6 mm sockets, so they lift off without clips Roof undersides are set at a 45° slope so each tier prints without supports The sloped roof sections are solid rather than a thin shell — print them with 3 walls and about 8% infill, since the walls carry the load Flat bottoms keep every piece stable on the build plate Walls are kept to a minimum of 2 mm for durable printing
Classic Heart Shape, 7 mm Thick
What it's for A plain, symmetrical traditional Valentine's heart that prints flat on the plate as a single solid piece. Use it as a decorative shape, a gift topper, or a starting point for ornaments and hanging decorations. Classic rounded-lobe heart silhouette with a V-shaped notch at the top and a point at the bottom Each lobe is a true smooth arc, so the outline reads as a continuous curve from above with no flat facets The sides running down from the widest point to the bottom tip stay straight, as intended Front edges rounded all the way around, including both lobes Back face completely flat, with no edge rounding, giving a clean surface to glue against or to cut a mounting interface into Prints without supports Dimensions Width: 60 mm Height: about 55 mm (54.9 mm as measured on the plate) Thickness: 7 mm Edge rounding: 3 mm radius, on the front face only 60 mm is the largest direction, so the heart sits at the size limit rather than under it Print notes Lay the heart flat on the build plate so the 7 mm thickness forms the height and the flat back becomes the bed contact face. At this size it prints quickly and needs no supports or rafts. Any common filament works; a glossy or silk finish suits the smooth faces, and the rounded edge catches light along the outline. Remix ideas Add a small hole near the top lobe for hanging Emboss a name, date, or short message on the front face Cut a keyhole slot or a knob interface into the flat back for wall mounting or a stand Change the front edge radius for a puffier heart or more flat side wall
Tannenbaum — Adventskalender mit Steckdeckeln
Tannenbaum-Adventskalender mit 24 Fächern, erhabenen Zahlen 1–24 und Steckdeckeln mit Griffknopf. Der Baum hängt in der Ansicht an einer roten Wand mit Lichterkette, Kugeln, Schnee und Stern. Features 24 Fächer in Reihen 1–6 plus Stamm mit 3 Fächern Deckel mit Griffknopf und Steckzapfen, per Reibung gehalten Schlüssellöcher auf der Rückseite zum Aufhängen part = "scene" zeigt die Wanddekoration, nur zur Ansicht Print notes Zum Drucken part auf row1 bis row7 oder doors stellen Die Wanddekoration gehört nicht zum Druckteil
Flat Letter R, One Layer
A single capital R that is too thin for most letter stencils or tags to hold a clean edge, printed as one layer instead. It sits flat on the bed in Roboto, 13 mm text size and 0.12 mm thick. Print notes Text size: 13 mm (Roboto, capital R) Thickness: 0.12 mm, which is one layer at a 0.12 mm layer height Print slowly and lift it with a thin blade, since it has almost no stiffness No supports needed