Pokéball Trainer Graded Card Stand 2 cgc
Created 3 days ago
Description
Freestanding display stand for a CGC graded card slab, with a Pokéball button on the base front and seven element badges. The slab drops into an open-top pocket in the frame, and the frame sides carry vertical POKÉMON and GOTTA CATCH 'EM ALL lettering.
- Base: 110 mm wide, 8 mm tall, with a raised plinth carrying the Pokéball button
- Pocket: 84 mm wide, 9.5 mm deep, open at the top
- Badges: fire, water, psychic, ground, fighting, fairy, grass on 13 mm discs, icons raised 1.5 mm
- Frame: 100 mm wide, 145.5 mm overall height
- Pokéball plinth overlaps the button back so the two print as one piece
Images
More like this
Explore more in Decor & Display →
Pokéball Trainer Graded Card Stand 2
A Pokéball-themed display stand for a graded card slab, with a red frame, a white base and a row of seven raised elemental badges: fire, water, psychic, ground, fighting, fairy and grass. The slab drops in from the top and lifts out for easy swapping. A tall front window shows the card. "POKÉMON" and "GOTTA CATCH 'EM ALL" run up the two sides, and a small Pokéball button sits on the front of the base. Design notes Frame 100 mm wide on a 110 mm wide base Slot 135.5 mm tall, open at the top Window 70 mm wide, with equal margins at top and bottom Badges are 13 mm discs with fine raised icons
Marquee Block TROY Name Stand
Tall condensed capitals in a movie-poster, marquee style, standing 50 mm high on a slim chamfered plinth. Letters are fused to the base so the whole thing prints as one sturdy piece. Letter height: 50 mm, Bebas Neue lettering Base: 60 x 22 x 4 mm with chamfered edges Prints flat on the base, no supports needed Pairs well with a desk, shelf or door-side display
pokemon shelf in three peices
A 400 mm wall shelf that splits into three printable sections, joined with dovetail tongues and glued together. Each piece fits a typical build plate. The shelf has closed ends, a front lip with a white panel, a raised Poké Ball and raised type symbols (electric, fire, water, grass, ground, psychic, fairy, fighting). It hangs on three countersunk screw holes. Remix hooks Cut positions: the splits sit at x = ±73 mm, giving pieces about 127 / 146 / 127 mm wide. Move them to balance piece widths, but keep them clear of the symbols and gussets. Joint size: each dovetail is 8 mm long and tapers from 8 mm to 12 mm wide, with 0.3 mm of clearance. Increase the clearance for a loose printer and decrease it for a tight one. Joint count: two tongues per seam, at y = -35 and y = -90. Add a third for more glue area. Print spacing: the pieces are laid out with a 15 mm gap. Set it to 0 to see the assembled shelf. Pairs with: CA glue or two-part epoxy for the seams, and No. 8 / M4 screws for hanging.
Antikythera Mechanism Desk Model
A simplified, life-size-style display model of the Antikythera mechanism: an upright case with a round front dial, a pointer, an open-backed gear train and a rear hand crank. Case 180 x 90 x 190 mm, open at the back to show the gears 130 mm front dial with ring grooves and 60 tick marks Nine spur gears (20 to 48 teeth, module 1.25) arranged in three layers, with phase-matched teeth so they mesh Fixed 4 mm pegs on the front wall carry the compound gears; the main 48-tooth gear is fused to a 6 mm axle that drives the front pointer Rear bearing bar supports the axle, with a crank handle on the back The gear train is a stylised interpretation, not a tooth-accurate copy of the original 30-plus gear mechanism. Print the case, dial, gears, axle and crank separately; the compound gears sit loose on their pegs with 0.3 mm clearance.
OO Gauge Flat-Pack Thatched Cottage with Dormers
Flat-pack 1:76 (OO gauge) detached cottage with thatched roof panels, dormer windows and a chimney, all printed lying flat. Fit notes Host: OO gauge, 1:76 scale; footprint 105 × 72 mm, 34 mm walls. Wall tabs use 2.4 mm slots for 2 mm tabs; test one tab first. Roof dormer openings are 16.4 × 9.4 mm; check one dormer against them before printing the rest. Each dormer cheek has a 4 mm tall gluing lip along its sloped lower edge, cut to the 37.4° roof pitch, to glue under the roof panel. Not a fit for other scales (N, HO) without resizing.
OO Mill Front and part-tapered Chimney Set
A four-panel tapered chimney with a straight brick base, paired with a half-relief two-storey mill front in OO scale. The wall, ten window frames and plank door all print flat. Each window frame and the door now carries a thin web around its outside edge to hold it down during printing. Remix hooks Web width (webw, 1.8 mm): wider grips better; keep it under half the 4 mm spacing so neighbouring webs stay separate. Web thickness (webt, 0.3 mm): roughly one or two layers. Thinner peels off easier, thicker holds harder. Window grid (14 x 28 mm frames, 4 mm spacing): change the spacing if the web is widened. Pairs with: the chimney set on the same plate layout, and a clear or painted glazing insert behind the frames. Print notes Trim the web with a hobby knife after printing, before fitting frames into the wall openings. Wall is 200 mm long and needs its own print separate from the chimney set.