Protective U-Brush Clamshell Case
Created 1 months ago
Description
A compact, mechanically-hinged clamshell case designed for standard U-shaped electric toothbrush heads.
- Two-piece Enclosure: Solid matching upper and lower shells provide physical protection during storage or travel.
- Positive Closure: Features a mechanical snap-tab latch for secure closing and a separate 3D-printable hinge pin.
- Handle Clearance: A clean 5×5 mm center opening allows the case to shut around the brush head while it remains attached to the toothbrush handle.
- Internal Standoffs: Four internal bumps securely locate the brush head without crushing the bristles.
Images
More like this
Explore more in Storage & Organization →
Bass Tackle Box With Hinged Lid
Tackle boxes that pop open in the boat, rattle hooks into the soft plastics, or lose a lid hinge get replaced. This one is a hinged bass tackle box with a locking front latch, adjustable dividers and a leaping largemouth bass on the lid, with SMITH FISHING raised underneath. Load-bearing numbers Base: 240 × 160 × 50 mm, 4 mm walls, 3 mm floor, rounded vertical corners. Lid: 240 × 160 × 22 mm, with a raised bass, ripples, waves, hooks and a border on top. Dividers: 5 removable cross dividers, 1.8 mm thick, sliding in 2.4 mm grooves at 38.5 mm spacing. Hinge: 5 interleaved knuckles across the back, joined by a 4.2 mm pin (197 mm long, printed separately). Latches: 2 front latches with 4.2 mm pivot pins. Each hooks under a ledge on the base. Printing Print every piece in the layout shown: base, lid, dividers, latches and pins are all separate. Lid: print upright. The underside of the top plate bridges across the cavity, so use supports or good bridging settings. Layer height 0.2 mm, PETG or ASA, 3+ perimeters. Hinge and latch pins can be glued or capped at the ends to keep them in.
Caja estanca con saliente frontal mo 1
Caja estanca para Garmin Montana 710, abierta por arriba, con ventana frontal, ranura de junta, tapa con orejas atornilladas, pestaña trasera con agujero de 6 mm y refuerzos. Interior: 94 x 37 x 192 mm Paredes de 4 mm Saliente frontal superior con dos triángulos laterales Tapa y lámina protectora incluidas
5 Bölmeli Vidalı Kapaklı Saklama Kabı
210 mm çapında, 60 mm yüksekliğinde yuvarlak bir saklama kabı. İçi, merkezden duvara 72° aralıkla çıkan beş bölmeyle eşit gözlere ayrılmış; bölmeler dişli boyun bölgesinde de devam ettiği için kapak takılıyken gözeler birbirine karışmaz. Kapak, gövdenin üstündeki dış dişe vidalanır; taşırken kendiliğinden açılmaz. Gövde ve kapak ayrı ayrı basılır. Remix için başlangıç değerleri Gövde: 210 mm çap, 60 mm yükseklik; yan duvar ve taban 1,6 mm, iç bölmeler 1,2 mm Kapak: 210 mm çap, 14,3 mm yükseklik, üst et 2,4 mm; düz yüzü tablaya gelecek şekilde basılır Diş: 12 mm boy, 5 mm adım, 3 ağızlı (hatve 15 mm), 0,5 mm boşluk; kapatmak için yaklaşık 0,8 tur (yaklaşık 290°) Diş çapı 204 mm, boyun iç çapı 197 mm; gövdenin üstündeki basamak her yanda yaklaşık 3 mm kalıyor Nereleri değiştirmek mantıklı Göz sayısı: bölmeler merkezden eşit açıyla çıktığı için sayıyı değiştirmek bölme açılarını da değiştirir; açıyı 72°'den farklı seçersen gözler eşit olmaktan çıkar, bunu bilerek yap. Bölme kalınlığı: 1,2 mm ince ve malzeme dostu; daha ağır parçalar koyacaksan kalınlaştır, ama göz hacmi daralır. Diş boşluğu: 0,5 mm baskıda rahat çalışıyor; makinen sıkı basıyorsa düşür, kapağı sık açıp kapatacaksan artır. Dış çap ve yükseklik: 210 × 60 mm raf ve çekmece için uygun bir başlangıç; aynı dişi koruyup gövdeyi derinleştirmek en kolay varyant. Alt kısımdaki diş dibi duvarı ince kaldığı için o bölgeyi basarken katman ayarlarına dikkat etmek gerekir. Beş gözü sayesinde dökme parçaları, vida ve küçük donanımı ya da atölye malzemesini tek kapta ayrı ayrı tutmak için uygundur; aynı diş ölçüsünü koruyan daha sığ bir gövde ya da daha çok gözlü bir üst katman iyi bir eşleşme olur.
Exploding Kittens Drawer Card Case
What it's for A two-part slide-out card case sized for a single poker-size deck, with the Exploding Kittens artwork carried on the top of the sleeve. The relief shows an angry cat beside a round bomb, bite marks cut into the bomb's edge, a dotted fuse and a spark. A large jagged orange explosion with an uneven outline and a smaller yellow core sits flat on the lid, centred on the title. Because the blast is fused to the surface rather than floating above it, the cat and bomb rise through it, so the explosion reads as a backdrop behind them and both stay clearly visible. The red "EXPLODING KITTENS" lettering stands on the core, kept low so it rises only about 3 mm above the blast. The drawer has a front pull panel with a thumb notch and slides out of the sleeve; a small snap detent on each side wall clicks it shut and lets go with a firm pull. A fused keychain loop on the back of the sleeve lets the case clip to a bag with a carabiner or split ring. Dimensions Sleeve: 76 × 100 × 34 mm, open at the front Drawer: 76 × 99 × 34 mm, with a front pull panel and thumb notch Card well: one compartment, about 64.6 × 91.5 mm, sized for a 63.5 × 89 mm deck Explosion: 57.8 × 44.8 mm blast, 2 mm thick, fused to the lid; core 42.2 × 29.2 × 1.5 mm on top of it Title lettering: 68 × 8 mm, standing on the core about 3 mm above the blast Bomb relief: 5 mm tall, with the paws and fuse lowered to sit level on top of it Keychain loop: 20 mm round lug, 4 mm thick, with a 7 mm hole, fused to the back of the sleeve and reaching about 70 mm out on Y Detents: one small bump per sleeve wall, with matching dimples on the drawer sides Print notes Print the sleeve upside down or with supports under the top, since the ceiling spans the full width. Print the drawer flat on its floor. The keychain lug sits flat on the build plate and needs no supports, but at 4 mm thick it is the lightest part of the case — thicken it if the case will hang from a heavy bag. The enlarged loop pushes the footprint out to roughly 70 mm on Y beyond the sleeve; check it against your plate before starting a full-bed print. Drawer clearance is 0.3 mm per side; adjust if the drawer binds. Sleeved cards need roughly 2 mm more in both the width and length of the well. The lowered red lettering sits directly on the orange and yellow blast, so contrast is low at small scales; check a render before printing the lid art very small. Detent tension has not been test-printed; sand or adjust the bumps if the drawer is too stiff or too loose. Remix ideas Widen the card well for a sleeved or double-sleeved deck. Burst the explosion over the top of the cat and bomb instead of behind them, accepting that it would hide most of the cat. Swap the round bomb for a C4 brick. Add a divider for tokens or a rules card. Thicken the keychain lug to 6 mm and widen the hole further for heavier bags. Trade the detents for a magnetic catch if you prefer a quieter close.
4x4 Gridfinity Baseplate with Bowtie Clips
What it's for A 4x4 Gridfinity baseplate that joins to neighbouring plates without interrupting the grid. Each outer edge carries four bowtie-shaped recesses on the underside, one centred on every cell edge. Butt two plates together and press a clip into the matching recesses from below; the clip sits flush so the top surface stays seamless and the 42 mm pitch carries across the join. The set prints as separate parts: the baseplate, the bowtie clips and a 1x1 bin. The bin has a foot profile that matches the baseplate pockets but no stacking lip. Dimensions Baseplate: 168 × 168 × 6.8 mm (4 × 4 cells on the 42 mm grid) 1x1 bin: 41.5 × 41.5 × 25.7 mm Bowtie clips: 16 × 79 × 1.2 mm, sitting in 1.4 mm deep recesses with 0.2 mm clearance Print notes Six clips are included, which is enough for one seam only — print four per cell edge you want to join. Print the clips flat in PETG or a tougher filament rather than PLA; at 1.2 mm thick they are the weak point of the set. Remix ideas Scale the plate to other grid sizes, or mix a 4x4 with smaller plates along the same seams. Add more 1x1 bins, or extend the bin family with deeper sizes. Add a stacking lip to the bin for stacked storage.
Caja Compacta para Ender 3
Caja con tapa y orejetas de cierre, ajustada para imprimirse en una cama de 220 × 220 mm como la de la Ender 3 Pro. El cuerpo mide 203 mm de largo y las orejetas ya no sobresalen tanto, así que cada pieza queda en 217 mm de ancho. Detalles Interior de 193 × 95 mm. 4 orejetas con agujero para insertos roscados M6. Tapa con solapa y ranura para junta de goma. Placa vertical con refuerzos. A tener en cuenta Cada pieza se imprime por separado; en el modelo aparecen una al lado de la otra solo para la vista.