Railing 2 m Long, 1.5 m High
Created today
Description
A railing panel with the dimensions written on every part, so nobody has to dig out a tape measure to check which bar is which length.
- Overall: 2000 mm long, 1500 mm high, 50 mm deep
- Posts: 50 x 50 mm, 1500 mm tall, labelled with height
- Top and bottom rails: 1900 mm between posts, 80 mm tall
- Bars: 12 vertical bars, 20 x 20 mm, 1260 mm long, 150 mm centre-to-centre
- Labels: raised 1 mm text on the front face (top rail length, 150 mm gap marks, bar lengths, post heights)
- Printing: designed at full size, so scale down or split into sections for a normal printer
Images
More like this
Explore more in Home & Fixtures →
Wall-Mounted Bedside Floating Shelf
What it's for A sleek floating shelf for beside the bed at about head height, sized for an ornament or a small potted plant. A back plate with four countersunk screw holes fixes it to the wall, and two triangular brackets support the top. The design is symmetrical, so printing two gives a matching pair for each side of the bed. Dimensions Shelf top: 200 × 120 × 12 mm, rounded edges Back plate: 170 mm wide, 6 mm thick, 70 mm tall including the shelf Screw holes: four, 4.5 mm shank with 9 mm countersink, set 80 mm apart, the upper pair just below the shelf Brackets: two, 6 mm thick, at X ±70 mm Print notes Prints with the top face on the bed, with no supports needed. Use wall plugs suited to your wall type and countersunk screws with heads up to 9 mm. Remix ideas Narrow the shelf for tighter spaces. Add a small front lip to keep ornaments from sliding off. Add a cable notch for a bedside lamp.
Straight Cylindrical Pipe
A straight cylindrical pipe with a uniform wall thickness, designed for fluid transfer, structure, or sleeving. Inner Diameter: 60 mm Outer Diameter: 64 mm Wall Thickness: 2 mm Overall Length: 60 mm
Wide Hook With Tall Front Lip
A small wall-side hook, 20 mm wide and 15 mm deep, with a 20 mm back plate, a flat 3 mm arm and a 50 mm upturned front lip. Remix hooks Width (20 mm): the one value shared by the plate, arm and lip. Widen it for heavier loads or narrow it for tight spots. Lip height (50 mm): lower it to around 10–15 mm for a simple catch, or keep it tall to hold flat items upright. Back plate height (20 mm): raise it to leave room for a screw hole or two. Arm thickness (3 mm): thicken it if the hook will carry weight. Pairs well with countersunk screw holes in the back plate or double-sided mounting tape.
HexGrip — Square-Cut Plywood Hex Clips
HexGrip is a two-clip press-fit system for building hexagonal shelving from 1/2 in plywood, now designed for plain 90° square-cut panel ends. Each slot ends in a solid stop 5 mm from the vertex centre, so neighbouring panels meet at 120° without colliding and no mitre cuts are needed. Features End Cap Clip: two slots at 120° for outer hexagon corners. Spoke Clip: three slots 120° apart for shared vertices in a hexagon network. Barbed slot walls with about 0.55 mm interference per side: ramped entry, steep faces that resist pull-out. Dimensions Slot width 13.0 mm, depth 19 mm Clip height 24 mm, arm length 30 mm Print notes Prints with the slot opening facing up, no supports needed. A single hexagon uses 12 clips, one on the front and one on the back of each vertex. Print one first to check the fit against your actual plywood thickness.
Cricket Calcium Duster Tube With Inner Screen
A cricket calcium duster tube that keeps powder in one end and crickets in the other. Crickets get dusted when the tube is shaken, because the powder passes up through a screen. The fix is a threaded screen collar between the tube and the powder cap, so nothing prints inside the tube. Key numbers (75% scale) Tube: about 56 mm outside diameter, about 115 mm long, walls about 1.9 mm Threads: about 3.75 mm pitch, same thread on all pieces, so the caps are interchangeable Screen collar: 19 round holes, about 4.5 mm each, in a separate print Powder cap: deep cup for powder, threaded only at the rim Stop flanges: on the tube, so caps seat at a fixed depth Printing Prints open end up, no supports needed PETG recommended, 0.28 mm layers, 10 to 15% infill Four separate parts: tube, powder cap, cricket cap, screen collar
Toolbox Front Latch Replacement C-Clip
Replacement front latch for a STUFF Basic 20 inch toolbox, for when the original hinge loop or hook has snapped. One solid C-profile part, 61 mm wide, with an open clip at the bottom that snaps onto the box pin and a filleted L hook at the top. Key numbers Overall: 61 mm wide, 65 mm tall, 18 mm deep Wall: 5 mm throughout Clip: 5.3 mm bore, 15.3 mm outer diameter, 5 mm gap Hook: 13 mm forward, 5 mm inside fillet, 2 mm outside fillet, 2.5 mm rounded tip Printing Material: PETG Supports: none Orientation: lay it on its 61 mm side so the C-profile faces up