Raised-Text Visitor Pass 110x70 mm
Created today
Description
A 110 × 70 mm single-piece visitor pass for Himalaya Public Sr. Sec. School, with a 2 mm base plate and bold text raised 0.8 mm above it. The three centred lines read HIMALAYA PUBLIC, SR. SEC. SCHOOL and VISITOR PASS.
- Plate: 110 × 70 mm, 2 mm thick, rounded corners, flat bottom
- Text: 0.8 mm raised, fused to the plate
- Total thickness: 2.8 mm
- Single colour, no supports needed
- Text size unchanged from the previous version
Images
More like this
Explore more in Gifts, Seasonal & Personalized →
Single-Colour Raised Text Visitor Pass
A 110 × 70 mm visitor pass with a 1.2 mm plate and bold raised lettering standing 0.6 mm proud, 1.8 mm total. It prints flat-side down in one colour with no supports. Remix hooks Text sizes: 6.5 mm for the school lines and 7.5 mm for VISITOR PASS. Raise them for a bolder look, but keep 4 mm of edge clearance. Plate thickness: 1.2 mm. Thicker gives a stiffer card, though the total height rises with it. Relief height: 0.6 mm. Match it to your layer height, for example 3 layers at 0.2 mm. Pairs with: a lanyard slot or clip tab added at one end.
110×70 mm Himalaya School Visitor Pass
Two-body visitor pass for Himalaya Public Sr. Sec. School: a white 110 × 70 × 4 mm plate with 3 mm corner radius, and solid dark-blue raised lettering. Fit and dimensions Plate: 110 × 70 × 4 mm, rounded corners. Letters: 2 mm proud of the plate, flat bottoms seated on the top face (overall height 6 mm). Text: HIMALAYA PUBLIC / SR. SEC. SCHOOL / VISITOR PASS, centred, well inside the 4 mm margin. Check before printing Confirm the text stays within 4 mm of every edge in your slicer. Assign the white and blue bodies to separate filaments. There is no hole or lanyard slot.
Mike Wazowski Horns for Shirt
Two horns to sew onto a maternity shirt for a Mike Wazowski costume. A loose horn flops or slides off fabric, so each one has a flat round base with sewing holes to stitch it down. Key numbers Height: about 47 mm each Base: 40 mm round disc, 3 mm thick Six 3.2 mm sewing holes around each base Print: base flat on the bed, no supports needed, cream or white filament
Armoured Oyster Bracelet Mid-Link
A reinforced stand-in for a broken oyster-style solid link, with a crowned top and an R45 concave underside that follows the wrist. The hinge ends are built to take the load. Female end: two Ø5.2 ears around a 5.2 mm gap; male end: one Ø4.6 × 4.4 mm tongue. Ø1.6 pin bores, 35.8 mm pin to pin. Underside pocket stops 11 mm from centre, leaving solid hinge zones. Filleted webs where the ears meet the body. Ream the pin holes to 1.5 mm after printing.
3.2 mm Jump Ring Georgie Letter Links
Seven individual letter links spelling G-e-o-r-g-i-e, made to be joined by metal jump rings into a name bracelet. Fitment Each link is a 14 × 14 mm plate, 3 mm thick, with the letter raised 1.5 mm in Luckiest Guy. A 3.2 mm hole runs front to back through a round tab on each side, so a ring passes through the flat face. Hole centres are 19 mm apart on each link; adjacent links join with one jump ring through facing holes. Check before printing Jump ring wire must be under about 3 mm, or the holes will not take it. Does not fit Rings with wire thicker than 3 mm, or links with a closed clasp-style bail.
46 mm Brooch with 32 mm Pin Bar Slot
A 46 mm round flower brooch with two layers of petals, a domed centre stone and a beaded rim. It is designed for a standard 30 mm pin-back bar glued into the back. Fit check Back groove: 32 × 6.4 × 1.2 mm. Measure your pin bar before printing. It fits bars up to about 30 mm long and 6 mm wide. Does not fit: clutch-style or screw-post backs. It has no hole for either. Print: face up with no supports needed. Use a multi-colour or paint the layers separately. Size: 46 mm across, about 6 mm tall.