Realtor Anniversary Commemorative Plaque
Created today
Description
A custom decorative plaque commemorating a tenth work anniversary for a realtor. The layout features personalized congratulatory text, a decorative scroll motif, and a detailed house icon to mark the occasion.
Key details:
- Solid rectangular base with rounded corners
- Raised outer border for framing the text
- Centered typographic layout spanning multiple fonts
- Stylized house icon and decorative center scroll
Photos
Technical views
More like this
Explore more in Gifts, Seasonal & Personalized →
150mm Bayonet Twist Vault
A 150mm mechanical drop-in vault, built around a 50mm twist-lift track. This replaces the friction fit of the original 150mm Borg Friendship Vault with a proper bayonet mechanism. The outer cage runs three 18mm tall helical tracks to guide the core. The top cap terminates in a 40mm hexagonal drive plug; dropping it onto the core and twisting counter-clockwise forces the payload to lift 50mm out of the chassis. Bore Clearance: The 98mm core runs inside a 102mm cage bore. Verify your machine holds tolerances on large cylinders. Support-Free: The massive 90mm flat bridges of the original have been replaced by mechanical vertical slots with 45-degree angled roofs. No supports needed for the cage or core lugs. Payload Capacity: The hollow inner void measures 76mm in diameter by 110mm deep. To assemble, line up the core lugs with the vertical entry slots on the inner walls of the cage, push down to the top stop, and twist right to lock it securely to the bottom.
Hartvormige fotolijst voor oma
Hartvormige fotolijst ontworpen rondom de standaardafmeting van een 10x15 cm foto. De lijst bevat verhoogde details zoals bloemen, kleine hartjes en de tekst in het Satisfy-lettertype. Omdat reguliere emoji's niet naar gcode vertalen, is het hartje in de tekst vervangen door een massief 3D-element. Constructie en Printen De Sponning: Aan de achterkant zit een uitsparing van exact 104x154 mm. Dit geeft rondom 2 mm speling voor de foto, plus de 3 mm dikke rugplaat. Ondersteuning: Print het hoofdframe plat op zijn rug. Voor de sponning van de foto is in de slicer een beetje "support" (ondersteuning) vereist. Montage: De rugplaat klemt strak in het frame. De losse standaard schuift onder een hoek van 45 graden in de rugplaat. Gebruik eventueel een klein beetje tape of lijm als de frictie van je print niet strak genoeg is.
Bracelet Octobre Rose 78mm
Un bracelet jonc simple et élégant, gravé du texte "OCTOBRE ROSE" en creux pour marquer l'événement sans nécessiter d'impression multicolore. Diamètre intérieur : 78 mm (ajusté pour un enfilage confortable) Épaisseur de paroi : 3 mm Hauteur : 12 mm Gravure : Découpée dans la paroi extérieure Impression : Conçu pour s'imprimer à plat sans aucun support
Snap-Fire — Auto Crossbow
A fully print-in-place auto-reloading mini crossbow. This model is scaled for standard 6mm airsoft BBs and features a gravity hopper that drops the next shot right onto the firing groove every time the string is drawn back. Features Auto-Reload Hopper: Stack 5-6 BBs vertically; pulling the string cycles the next shot. String Guide Tracks: Side rails capture the rubber band on release so it flies perfectly straight without jumping off the barrel. Print-in-Place Trigger: The trigger mechanism prints fully assembled with a built-in pivot pin. Just wiggle it free after printing. String a standard rubber band between the side notches on the front arms and feed it through the guide tracks to shoot.
X26 Prop Holster, 2.21 in Belt, Strap
A prop X26 holster pouch with a belt loop and a separate U-shaped retention strap, sized for a duty belt 2.21 in (56 mm) tall and 0.21 in (5.3 mm) thick. Fit notes Belt slot: 60 mm tall, 7.5 mm thick. It will not fit belts wider than about 58 mm. Pocket: tapers from 70 × 44 mm at the base to 84 × 48 mm at the mouth, 130 mm deep. These are estimated prop dimensions, not measured. Check your prop before printing. Strap: a separate U-shaped piece with keyholes that mate with the two 5 mm studs on the rim. It prints flat and is not attached to the pouch. Not a working Taser holster. Prop use only.
Lemon Slice Earring Cover
A two-piece clamshell case designed to snap cleanly over a 29mm circular earring. Both halves print face-down and feature the decorative lemon slice pattern on their outer faces. What it's for Transforming a plain hoop or disc earring into a 3D fruit slice without permanent modification. The two halves securely press-fit together, sandwiching the jewelry inside while leaving a notch for the earring hardware to pass through normally. Dimensions Overall size: 36 mm diameter, 6.5 mm total thickness when assembled. Internal pocket: 29.5 mm diameter by 2.5 mm deep, tailored for a 2 mm thick earring. Hardware slot: 4 mm wide notch at the top edge. Assembly Prints as two separate pieces side-by-side, with the decorative faces flat on the bed. Features four alignment pegs that snap the halves together. The symmetrical layout ensures the hardware slots align perfectly when closed.