SUPPORT PRINTYTRON
New Model
Loading 3D preview…

Retro TV Enclosure v2

Made by LayerEagle

Created 1 months ago

Desk & Techrp2040tv-enclosureretro-techspeaker-grillesprint-in-placeno-supportsthick-walls
Remix this model →

Description

A reinforced retro TV enclosure designed for an RP2040 video player project. The walls have been bulked up for extra durability without compromising the interior payload space, while side-firing one-inch speaker grilles and a classic bent antenna give it a finished look.

What it's for

Built to house a no-solder RP2040 media player. The clamshell locks together with an integrated friction fit and the entire model prints flat on the bed with zero supports.

Dimensions

  • Internal volume: 150 × 80 × 50 mm
  • Wall thickness: 5 mm (beefed up from standard)
  • Grilles: 25.4 mm (1 inch) perforated arrays on the left and right panels

Assembly

Both halves print cleanly flat. Slide your display into the front bezel's chamfered recess, route the cables out the back USB port, and firmly press the halves together until the interior ridges lock.

Images

SUPPORT PRINTYTRON
Tip Jar
Printytron built this for free. If it saved you a trip to the shop, a tip helps keep it free.
Need filament at a great price?
Printing this one? Stock up through our eSun partner link — your price stays the same, but Printytron gets a small commission to go towards our costs.
Mini-Server-Box with Feet, Lid and Fan

Mini-Server-Box with Feet, Lid and Fan

What it's for A solid-walled enclosure for hiding and cooling equipment. Every side wall is closed, and the only airflow path is a sturdy grid cut into the floor, so the box stays dark and quiet from the sides. A 30 × 20 mm cable hole in the lower rear corner lets wiring in and out, and the flat lid lifts off for access. The model prints as separate pieces: the box, the lid and four feet. The lid is a flat plate with a locating lip underneath, slightly larger than the box on every side so it overhangs and can never drop inside. Each foot carries its own coarse threaded stud, so the feet screw directly into matching threaded holes in the floor bosses with no separate fasteners. Dimensions Box: 290 × 200 × 130 mm, with 4 mm walls, solid on all four sides, an 8 mm floor, and a 50 mm solid border around the floor grid. The floor grid is centred on the narrower floor. The thicker floor makes the mesh bars deeper, so airflow per opening drops slightly. Inside fillets: 10 mm radius on the vertical corners and the floor-to-wall edges, stopping 15 mm below the rim. The top 15 mm stays square so the lid and its lip fit without changes. Lid: 294 × 204 mm, 9 mm overall with a 5 mm plate and underside lip; overhangs the box by 2 mm on all sides; 140 mm fan opening and four 3 mm fan screw holes at 124.5 mm center-to-center. Cable hole: 30 × 20 mm in the rear wall, set 20 mm from the left edge and 12 mm above the bottom, inside the solid section so it doesn't weaken the corners. Feet: four solid 24 mm discs, 10 mm tall, each with a 6 mm thick, 8 mm long threaded stud on top; 18 mm overall. The studs use a 1.5 mm pitch. Foot sockets: four corner bosses widened to 14 mm, with threaded holes 6.6 mm across and 11 mm deep at the same 1.5 mm pitch, giving about 0.6 mm clearance on diameter. Print notes Print the box, lid and feet separately. Print the lid lip-side up so its flat face sits on the bed and the lip rises clear of the plate. The floor grid benefits from enough perimeters to keep the bars sturdy. The threads have not been test-fitted; if the feet bind, raise the socket diameter slightly, and if they wobble, lower it. Test-fit the fan and check its screw-hole spacing before committing to a full print. Remix ideas Add a removable filter frame behind the fan opening. Add internal standoffs or a shallow tray for mounting equipment inside. Resize or duplicate the rear cable port for thicker cable bundles. Swap the floor grid for a denser or more open pattern to change the airflow.

ConcreteLynx · 5 days agoRemix →