Simple 2-Inch Cylinder
Created 1 months ago
Remixed once
Description
A heavy-duty 2-inch diameter puck, built exactly 1 inch thick. It's a completely blank slate standing by for its real job, complete with 1 mm chamfers on the top and bottom edges so it prints cleanly without an elephant's foot.
Remix Hooks
- Dimensions: 50.8 mm diameter, 25.4 mm height.
- Add a center hole: Subtract a cylinder to turn this into a heavy-duty spacer.
- Hollow it out: Shell the inside to use it as a custom project box or potting cup.
- Scale the Z-axis: Squash it down in your slicer to use it as a coaster or shim.
Photos
Technical views
More like this
Explore more in Workshop & Tools →
5 x 5 x 1 mm Square Block
A plain square block measuring 5 mm by 5 mm by 1 mm, flat on the bed and ready to print. Remix hooks Footprint: 5 x 5 mm is the starting value. Change it to make a tile, spacer or shim. Thickness: 1 mm is about five layers at 0.2 mm. Raise it for a sturdier piece. Edges: Add a small chamfer or rounding for a softer look. Keep it under 0.5 mm at this size. Pairs with: Use it as a test cube for tolerance checks, or as a base for a hole, text or a peg.
Sleeve — 0.385" OD Spacer Tube
Sleeve is a plain, precise hollow cylinder sized in inches: a straight-through bore and a clean outer wall, ready to use as a spacer, bushing or standoff. Dimensions Outer diameter: 0.385" (9.78 mm) Inner diameter: 0.26" (6.60 mm) Length: 0.75" (19.05 mm) Wall thickness: about 0.0625" (1.59 mm) Print notes Print standing on end, no supports needed. Bore may print slightly tight; ream or scale up a touch if fit matters.
Hex Tube 40 mm Tall With Center Bore
A hex tube, 4 cm tall, for when a round spacer or standoff spins or rolls where a flat-sided one would hold still. The 2.5 mm bore runs the full length so a rod, wire or screw passes straight through. Key dimensions Height: 40 mm Width: 5.15 mm point to point Center bore: 2.5 mm diameter, through the full length Printing Print standing upright, no supports needed. Walls are thin at the hex flats, so use at least 2 perimeters and a small nozzle if possible.
69 mm Round Spacer, 5 Holes
A round spacer 69 mm in diameter and 10 mm tall with a 40 mm center bore and five 5.5 mm through-holes on a 54 mm bolt circle. Outer diameter: 69 mm Height: 10 mm Center hole: 40 mm Bolt holes: 5 × 5.5 mm on a 54 mm circle Hole spacing: 68°, 72°, 72°, 68°, 80° (the 80° gap is between the last and first hole) Prints flat with no supports
door lock
Rectangular block, 100 mm long, 24 mm wide and 15 mm tall, with a 16 mm wide by 11 mm deep groove running the full length along the top centre. The groove size is engraved into the groove floor as "16 x 11 mm". Overall size: 100 x 24 x 15 mm Groove: 16 mm wide x 11 mm deep, open at both ends Side walls: 4 mm; floor: 4 mm Engraving: 0.6 mm deep, readable from above Prints flat with no supports
outside hat
A plain flat disc in the spirit of an oversized washer or a vinyl-record blank: 3 inches across, 1/8 inch thick, with a clean 1 cm hole through the centre. Prints flat with no supports. Diameter: 76.2 mm (3 in) Thickness: 3.175 mm (1/8 in) Centre hole: 10 mm Good for spacers, coasters, templates, or as a base for other builds