Made by MellowCrowbar
Created 2 days ago
Description
A single ski that fits under a stroller wheel so the stroller slides over snow instead of sinking into it. The ski has a curled-up front tip and carries a U-shaped wheel holder at its middle; the wheel drops into the cradle and is strapped down through the slots, so the stroller rolls on the ski rather than on the tyre.
A 220 mm wheel is only cradled at the bottom of the holder: the walls hold it sideways but do not wrap around it, so strap it down firmly through the slots before use. Taller walls are an option for rough snow.
Measure the wheel width before printing; the 55 mm gap is the only fitment that matters here, and a wider or narrower wheel needs the cradle resized.
Images
A stroller ski for snow: a runner that takes the place of a stroller wheel, with the wheel held between two upright walls. The ski is 280 mm long end to end and 80 mm wide, flat at the tail, with a front tip that sweeps up through a tight 100 mm radius over 50° and rises to about 39 mm above the plate. Seen from above, the front narrows from the full 80 mm width to a point, giving it the spear-shaped profile of a classic ski. The wheel holder is 71 mm wide, 120 mm long and 49 mm tall — two flat upright walls with 55 mm clear between them, tied together by cross ribs at the front and back. Two strap slots run straight through both walls, one 20 mm above the other. Both are 30 mm along the ski and 5 mm tall; the lower starts 5 mm above the ski surface and the upper at 25 mm, so a flat strap up to about 30 mm wide can pass through and wrap under the wheel. The 55 mm wall gap is the constraint; almost everything else is a choice. The walls are straight, so a 220 mm wheel sits uncradled between them — the curved seat matched to that diameter is the obvious next version. Remix hooks Ski footprint: 280 × 80 mm is a starting value, not a rule. Longer and wider spreads load in deep snow; shorter turns tighter. Keep the holder centred over the wheel position and the rest is free. Tip taper: the point is currently gradual, starting well back from the tip. Lengthening the taper softens the look and keeps strength in the tip; shortening it sharpens the spear but weakens the point and makes it dig in — worth changing one step at a time. Tip radius: 100 mm through 50°. A smaller radius kicks sharper and higher for soft snow; a larger one rolls flatter on packed surfaces. Mirror it onto the tail for a reversible ski. Wall gap: 55 mm clear between the walls is the hard constraint — change it only for a different wheel or hub width. Strap slots: two slots at 30 × 5 mm, set 20 mm apart, with the lower 5 mm above the ski surface. Resize them to the strap on hand; the spacing is free if the strap should take a different path under the wheel. Wheel seat: straight walls mean no cradle. A curved seat matched to the 220 mm wheel is the obvious variant, and the flat inner wall face is a clean place to start it. Pairs with: a stroller wheel position and a flat strap; print a second, mirrored ski to convert both wheels.
A single-arm servo horn for the SG90 micro servo, with a 3.2 mm linkage hole 12 mm from the output shaft centre. Fitment Fits: SG90 and compatible 9 g servos with the 21-tooth, ~4.8 mm output spline. Does not fit: MG90S metal-gear servos with a different spline count, or 25T servos such as MG995/MG996. Arm: 12 mm centre distance, 4 mm thick, rounded edges. Check before printing Test the spline bore on a scrap print. Bore size is ~4.9 mm with small tooth notches, and printer tolerance varies. Adjust it if the fit is loose or tight. The part prints flat with no supports, and PLA works.

A sleeve that drops into an oversized cup holder and shrinks it, so a slim energy can sits snugly instead of rattling around. Three angled flex fins on the outside wedge the sleeve into holders of different widths. What it's for Sizing down a large truck cup holder for a slim energy can or a standard 500 ml can. Holding the can upright without side-to-side movement. Fitting holders from roughly 80 mm to 95 mm across, using the three flexible fins on the outside. Dimensions Height: 70 mm Body outer diameter: 76 mm Inner bore for the can: 66 mm Base well: 70 mm diameter, 4 mm deep, for the can's bottom rim Drain hole in the base: 20 mm Fins: 3, spaced 120° apart, spanning about 80–95 mm overall, positioned between 14 mm and 56 mm up the body Top edge: small flared lead-in for easy can insertion Print notes PETG works for the whole part. TPU for the fins gives more flex without cracking. Print upright with the base on the bed. No supports are needed for the body. The fins are thin blades, so they bend inward when pushed into a holder. A snug can may need a little extra bore clearance. Fit has not been tested in a real holder, so check your holder's diameter first. Remix ideas Change the bore diameter for other cans or bottles. Add more fins or make them thicker for a firmer grip. Shorten the body for a low-profile holder. Increase the drain hole or add slots to let water escape.
Gancho de garrafa de treino em J, 200 mm, com braçadeira bipartida na base: corpo fixo ligado à haste e tampa separada que fecha por encaixe de pressão ao redor da alça de 12 × 24 mm. Pontos de remix Snap-fit: ganchos flexíveis de 8 mm de comprimento, 1,8 mm de espessura e ressalto de 0,6 mm (armlen, armt, ridge). Entrada em rampa, retenção reta. Folga: 0,2 mm entre tampa e corpo (gap). Trava extra: furo M3 em gota atravessando tampa e corpo, com porca sextavada embutida no lado +X. Paredes: wallx (6,4 mm) e wallf (7,5 mm) definem o tamanho externo; reduza se o furo M3 for dispensado. Haste e gancho: inalterados, seção 10 × 14 mm, bojo de 40 mm, boca de 34 mm. Combina com: parafuso M3 e porca M3 (opcionais); imprima corpo e tampa separados em PETG ou PLA.
Straight and curved RC track pieces sized to fit a 250 x 250 mm print bed, using the same 90 mm wide track and bulb-and-socket latch as the rest of the set. What it fits Built for printers with a 250 x 250 mm bed or larger. Mates with the existing 90 mm wide pieces (80 mm clear lane, 5 mm rails) through the same latch with 1 mm clearance. Pieces Straights: 50 mm and 150 mm (the 200 mm straight also fits). 180° hairpin at 70 mm centreline radius, about 230 mm wide. 30° at 250 mm radius, 45° at 200 mm, 60° at 150 mm, 90° at 120 mm. Check before printing The footprint of each piece is measured from the model, but measure your bed's usable area, since brims and clips reduce it. Does not fit The earlier 180° hairpin at 100 mm radius, the main junction (about 440 mm) and the multi-way junctions are larger than a 250 mm bed. The latches have not been test-fitted.
608 rulman yuvalı, M3 cıvata ve somunla kapanan iki yarım gövdeli, 2 vitesli kayar dişli şanzıman. Giriş milinde 12T ve 24T sabit dişliler, çıkışta 36T+24T kayar dişli kümesi bulunur; 1. vites 3:1, 2. vites 1:1 ve iki çiftte de eksenler arası mesafe 36 mm'dir. Altı parça ayrı basılır ve montaj ister: alt gövde, üst kapak, giriş mili, D profilli çıkış mili, kayar dişli kümesi ve vites kolu. Üst kapağın dış yüzeyinde, kapanmış halde kullanıcıya bakan tarafta 0,8 mm derinliğinde oyulmuş "benze" yazısı vardır. Kapak ters basıldığı için yazı tablaya oturmaz. Gövde iç duvarları hızlı baskı için 1,6 mm'ye inceltilmiştir; rulman yuvaları, cıvata kulakları ve mil uçlarının duvarları 2,4 mm'de kalır. Uyumluluk 608 rulman: 8 mm iç çap, dört adet. Rulman kullanılmazsa basılı kaymalı burç seçeneği vardır. M3 cıvata: yaklaşık 12–16 mm, altı adet; M3 somun altı adet. Mil uçları: giriş ve çıkışta 5 mm D profil veya 5 mm D delik. Dişli standardı: modül 1.5, 20° basınç açısı, düz dişli. Baskı öncesi kontrol Alt gövde ve üst kapak, baskı yerleşiminde yaklaşık 92 × 93 mm taban alanı kaplar; tabla en az bu ölçüyü almalıdır. 608 rulman yuvası 8 mm iç çapa göre çıkar. Rulman yerine basılı burç kullanılacaksa mil çapı aynı ölçüde tutulmalıdır. Gövde iç uzunluğu üç dişli konumu ve kayma payı nedeniyle yaklaşık 60 mm'dir; 36T dişli yüksekliği belirler. Uymadıkları 90 × 50 × 45 mm gövde ölçüsüne sığmaz. Gerçek dış ölçü yaklaşık 92 × 93 × 32 mm'dir. Tek kayar dişliyle 3:1 ve 1:1 aynı eksen mesafesinde elde edilemez; bu modelde kayar küme 24T+36T çift dişlidir. Hazır bir redüktörün yerine doğrudan geçmez; miller, dişliler ve gövde birlikte basılan bağımsız bir düzenektir. Destek malzemesi gerektirmeyecek şekilde düz yüzeyler tablaya gelecek biçimde yerleştirilmiştir. PLA veya PETG ile 0,2 mm katman yüksekliğinde basılabilir; dişliler ve miller için %40–60 dolgu, gövde için %20–30 dolgu yeterlidir.