Sliding BGA Ring Box
Created today
Description
A giant BGA microchip designed as a geeky ring box or secret stash. The two-piece design features an internal 42mm cavity and a satisfying dovetail slide mechanism to keep it securely closed.
- Support-Free Design: Both pieces are oriented to print flat on the bed without any support material. The lid is printed face-down.
- Authentic Details: Features a hollow-center BGA ball grid on the bottom and deeply engraved tech lettering on top.
- Perfect Fit: The built-in 0.25mm clearance on the dovetail ensures a smooth sliding action right off the printer.
Images
More like this
Explore more in Gifts, Seasonal & Personalized →
Classic Stacking Ring Toy
A classic educational stacking ring set designed for early motor skills. The design features thick, fully rounded components to eliminate sharp edges and ensure safe handling. The generous clearances make stacking easy for small hands. What it's for Perfect as a robust, classic nursery toy or a personalized gift for a toddler. It teaches size sorting and hand-eye coordination. Dimensions Overall Height: 130 mm Base Plate: 100 mm diameter Stacking Rings: 85 mm, 70 mm, and 55 mm outer diameters Internal Clearances: 1.5 mm gap between the post and the rings to prevent binding. Print notes Print the rings and base separately on their flat bottom faces. Use a high infill for the base to give the toy a low center of gravity. No supports are required for any of the parts.
150mm Bayonet Twist Vault
A 150mm mechanical drop-in vault, built around a 50mm twist-lift track. This replaces the friction fit of the original 150mm Borg Friendship Vault with a proper bayonet mechanism. The outer cage runs three 18mm tall helical tracks to guide the core. The top cap terminates in a 40mm hexagonal drive plug; dropping it onto the core and twisting counter-clockwise forces the payload to lift 50mm out of the chassis. Bore Clearance: The 98mm core runs inside a 102mm cage bore. Verify your machine holds tolerances on large cylinders. Support-Free: The massive 90mm flat bridges of the original have been replaced by mechanical vertical slots with 45-degree angled roofs. No supports needed for the cage or core lugs. Payload Capacity: The hollow inner void measures 76mm in diameter by 110mm deep. To assemble, line up the core lugs with the vertical entry slots on the inner walls of the cage, push down to the top stop, and twist right to lock it securely to the bottom.
Luggage Strap Tag, 5 mm Slot, STEVE
A 90 × 50 × 3 mm luggage tag with a 5 × 22 mm strap slot and the name STEVE raised inside a recessed label panel. Fitment Fits straps up to 5 mm thick through the 22 mm-wide slot. Does not fit wide or double-layer straps, or standard key rings without a loop. Measure the strap thickness before printing; the slot is 5 mm. The lettering stands 0.9 mm proud of the panel floor and sits below the tag's top surface, so it is protected from rubbing.
Kids Fidget Board with Spinner
A fidget board for small hands: a base with a three-lobe spinner and a sliding button in a track. Printed as five separate pieces, so nothing fuses and no supports are needed. Base: 70 × 36 mm with a spinner pocket, a fixed axle and a through slot with an underside recess. Spinner: prints flat, drops over the axle with 0.7 mm clearance per side. Axle cap: glues onto the peg at the top of the axle to hold the spinner on. Slider button: prints flat with the stem pointing up. The stem passes through the slot. Retaining foot: glues onto the stem underneath, inside the recess, so the button slides but cannot lift out. Assemble in this order: spinner, then cap; button stem through the slot, then foot glued on. Use glue suited to the filament, and check that glued parts are fully secure before giving the toy to a young child.
5mm Bore Snowman Ornament
5mm bore snowman plate. Replaces flimsy universal-fit ornaments with a rigid, one-piece PLA blank. The main body prints completely flat at a 3.5mm maximum depth, maintaining a minimum structural web of 2.5mm throughout. Check the hanger fitment before printing: Accepts standard 4mm wire hooks Clears bare natural spruce tips up to 4.5mm thick Does not fit 1/4" wood dowel branches on artificial trees Overall envelope is 65mm x 80mm. No supports required.
70mm Santa Face Ornament
A single-piece stylized Santa Claus face ornament, designed to lay flat on the print bed. The model uses raised geometric profiles for the moustache, nose, and hat brim, alongside through-cut eyes and mouth for visual contrast without requiring painted textures. Specifications Dimensions: 70 mm wide, 75 mm tall, 3.5 mm overall thickness. Structural Base: 2.5 mm solid backing layer. Hanging Interface: 5 mm circular bore located in the top pom-pom. Print Settings: Prints flat without supports. A filament swap at Z=2.6 mm allows the raised accents to be printed in an alternate color.