Standard 140x40 Gehäuse
Created today
Description
Gehäuseunterteil mit Außenmaßen 140 x 40 x 25 mm und 3 mm Wandstärke.
- Passung: Der Deckel hat eine Innenlippe mit 0,5 mm Gesamtspielraum (0,25 mm pro Seite).
- Druck: Beide Teile liegen flach auf dem Druckbett (Deckel liegt auf der Oberseite) und benötigen keine Stützstrukturen.
- Kapazität: Innenraum misst effektiv 134 x 34 x 22 mm.
Images
More like this
Explore more in Storage & Organization →
Split 13-Inch Slip Box
A simple, cleanly split rectangular enclosure meeting a 3" × 1" × 13" outer footprint. Designed to print standing vertically on the build plate, the two halves meet in the middle with a sliding half-lap joint that handles alignment and friction. Remix Hooks The source relies on a few key parameters that dictate the fit and feel. If you pull this into a remix, check these first: Dimensions: Currently W = 76.2, D = 25.4, and L = 172.6 (for each half, achieving the 330.2mm total length). Tweak these to fit whatever board or gear you are housing. Wall: Set to 3mm. This gives enough meat for the half-lap cut (leaving 1.5mm walls at the joint) without feeling overly bulky. Clearance: The joint runs a comfortable 0.4mm tolerance. Tighten it to 0.2mm if your printer is dialed in and you want a semi-permanent friction fit, or loosen it if it binds. Lip Length: The 15mm overlap keeps the assembled box rigid, but dropping it to 8-10mm would save a bit of plastic if the contents don't flex.
Ühe Otsaga Suletud Sahtlikarp
Sahtel kiilub kinni, sest pole kuskilt korralikult kinni võtta. See on suletud tagaseinaga lihtne kest, millel on nüüd sahtli ees korralik väike näpu-kõrgendus, et seda saaks mugavalt ja ilma küüsi murdmata välja tõmmata. Mahutavus: Täpselt 200 × 50 × 50 mm kasulikku ruumi. Seinad: 1.5 mm, prinditav ilma tugedeta. Liikumisruum: 0.5 mm lõtk külgedel tagab sujuva liugumise.
13-Inch Magnetic Sliding Box
What it's for A minimalist 13-inch sliding box with an ultra-flush interior (3.5" wide by 1" deep) and heavily magnetized slip joints. Designed for vertical printing without supports, this two-part closure uses eight 5x2 mm magnets hidden inside the 6 mm thick walls of the step-joint, creating a completely smooth interior cavity once assembled. Dimensions Interior: 88.9 × 25.4 × 330.2 mm (3.5 × 1 × 13 inches) Exterior Shell Walls: 6 mm thick Base Ends: 3 mm thick Magnet Sockets: Sized for 5x2 mm disc magnets (5.2 mm diameter x 2.3 mm deep) Print notes No supports needed. The halves print upright on their closed ends. 0.2 mm clearance is built into the male slip joint for a smooth glide up until the magnets catch. Add a small dab of superglue to the magnet pockets before pressing them in.
Wide Friction Slip Box
A 3-inch box is useless when the board you need to house is exactly three and a half inches wide, and a standard slip-joint rattles loose the second it goes into a bag. This version stretches the outer footprint to 3.5 inches to clear the hardware, and packs an extra millimeter of width onto the male tongue to bite into the female half and hold. Width: 3.5" (88.9mm) outer footprint. Fit: The male lip is offset an extra +1mm in width for a tighter friction lock. Print: Prints vertically on the flat bases, no supports needed.
VoltGrid — Print-in-Place Battery Case
A high-capacity, print-in-place storage case holding 104 AA batteries in a skeletal, material-saving grid. Designed specifically for FDM printing without supports. Features Zero Assembly: Prints flat with a fully integrated, captive 45-degree cone hinge mechanism. Just pop it off the bed and fold it closed. Skeletal Organizer: The lower grid provides 0.4 mm of clearance for 14.5 mm diameter AA batteries, but uses open walls to drastically cut filament usage and print time compared to solid block designs. Snap Latch: A flexible cantilever tab locks the lid securely down over a heavy chamfered ledge on the bottom box. Dimensions Flat Printing Footprint: 228 mm × 292 mm Closed Dimensions: 228 mm (W) × 142 mm (D) × 60 mm (H) Capacity: 104 cells (13 × 8 grid)
Side-Pinned 40-Quarter Dispenser
A gravity-fed mechanical magazine for standard U.S. quarters. The vertical tube stores up to 36 coins, while a sliding escapement mechanism stages and drops exactly four quarters ($1) per full pull. Design and Fitment Capacity: 40 quarters maximum (36 in the tube, 4 seated in the slider). Clearances: The magazine bore is 25.2 mm (oversized from the 24.26 mm quarter) to prevent binding, with a 28.8 mm x 7.6 mm slider track for horizontal travel. Structural Details: The base of the primary magazine tube features a 4 mm flared buttress, preventing shear failure across the layer lines when fully loaded. Hardware: Fully printed, no external fasteners or springs required. The side-mounted 4.0 mm stopper pin captures the slider in the track and sets the 26 mm travel limit.