Triple Socket Adapter Floor Cradle
Created 2 days ago
Description
What it's for
A one-piece floor cradle that holds a triple 12V socket adapter horizontally under a dashboard. The front and top stay open, so the sockets and power switches remain reachable, and side windows keep the side USB ports clear.
Dimensions
- Adapter: 100.4 x 60.85 x 31.72 mm, about 1 mm clearance
- Side walls: 3 mm thick, 14 mm tall
- Side windows: 18 mm long, centred 51.38 mm from the front (plus 1 mm clearance)
- Back lip: 12 mm tall with reinforced corners
- Mounting ears: 16 mm each end, countersunk screw holes
Remix ideas
- Change the window length to fit a different USB port.
- Add a third screw hole at the back.
- Lengthen the ears for wider mounting.
Images
More like this
Explore more in Automotive, RC & Hobby →
Gancho de Garrafa com Braçadeira Snap
Gancho de garrafa de treino em J, 200 mm, com braçadeira bipartida na base: corpo fixo ligado à haste e tampa separada que fecha por encaixe de pressão ao redor da alça de 12 × 24 mm. Pontos de remix Snap-fit: ganchos flexíveis de 8 mm de comprimento, 1,8 mm de espessura e ressalto de 0,6 mm (armlen, armt, ridge). Entrada em rampa, retenção reta. Folga: 0,2 mm entre tampa e corpo (gap). Trava extra: furo M3 em gota atravessando tampa e corpo, com porca sextavada embutida no lado +X. Paredes: wallx (6,4 mm) e wallf (7,5 mm) definem o tamanho externo; reduza se o furo M3 for dispensado. Haste e gancho: inalterados, seção 10 × 14 mm, bojo de 40 mm, boca de 34 mm. Combina com: parafuso M3 e porca M3 (opcionais); imprima corpo e tampa separados em PETG ou PLA.
Technic Plate 2x4 With Holes, Set of 6
A 2x4 plate with no way to pass a Technic pin or axle through it is a dead end in a studless build. This plate has three holes on the centre line, so pins and axles go straight through. Six are laid out flat for one print run. Key numbers Plate: 32 x 16 mm, 3.2 mm thick, studs on 8 mm pitch Studs: 4.8 mm diameter, 1.8 mm tall Holes: three, 4.8 mm diameter, on the centre line, 8 mm apart Print: flat, no supports, 0.2 mm layers; test one first to check clutch fit
Pinch-Feed Drive Roller, Print-Ready
A knurl-free drive wheel for a pinch-feed wire feeder, built like a small industrial pulley: a 24 mm roller with a hub on one side and a blind D-bore that slips over a 5 mm D-shaft. The model is just the roller, standing on its hub and ready to slice. Design notes Blind D-bore, open on the hub face and closed by a wall on the far end, so the closed end shows which side stays out. M3 grub screw hole with a trapped hex nut that slides in through a slot open to the rim. Counterbored screw recess 2 mm deep, so a headed M3 screw sits below the surface and a nylon or TPU sleeve goes on smooth. Hub spaces the roller off the motor face so the two do not rub. Printing Stands on the hub with the bore opening onto the bed, so there is no bridging inside the bore and no supports are needed. Printing upright keeps the roller round. Suggested: PETG, ASA or nylon, 3 or more walls, 25–30% infill.
iPhone 15 Pro Bike Mount 31.8mm Bar
Handlebar phone mount sized for the iPhone 15 Pro (146.6 × 70.6 × 8.25 mm). A back plate with a weight-saving window holds the phone, four L-shaped corner clips wrap the edges and hook 4 mm over the screen face, and a split clamp on the back fits 31.8 mm handlebars. The clamp split is present, but no bolt tab or hardware mounting is included yet. A strap or added bolt tab is needed to tighten it on the bar. Specifications Phone: iPhone 15 Pro, 146.6 mm tall, 70.6 mm wide, 8.25 mm thick Pocket: 71.2 × 147.2 mm inside (0.6 mm total clearance) Corner clips: 4, each with 18 mm arms along both edges, 2.4 mm wall, 4 mm lip over the face Back plate: 3 mm thick, 6 mm corner radius, central cutout to reduce weight Clamp: 31.8 mm bore, 4 mm wall, 50 mm wide, split at the bottom Overall size: 76 × 152 mm footprint, about 54 mm tall in the print orientation Print notes: supports needed under the back plate in the modelled orientation; PETG or ASA suggested for heat and vibration Parts: back plate, corner clips, handlebar clamp (single welded body)
90° Bevel Gearbox Assembly
A fully functional 90-degree bevel gearbox with 5 mm hex bores on both the input and output gears. The split housing prints without supports and clamps the gear stack together when the face flanges are bolted down. Specifications Transmission: 1:1 ratio bevel gears (16 teeth, 90-degree mesh). Input/Output: 5 mm hex bores on both gears, measuring 5.2 mm across the flats including 0.2 mm printing clearance. Housing: Split base and top, each 45 × 45 × 20 mm, designed to print flat without supports. Mounting Interfaces: Four 4.3 mm clearance holes on each face flange, arranged in a 25 mm square pattern. Assembly: The housing halves are clamped together when bolted to a surface using the face flanges; an extra M3 hole in the rear corner provides optional tightening. Printing: All pieces print flat without supports; the housing and gears assemble after printing.
Ball Hitch 7 mm Tall, 3.4 mm Post
A small ball hitch with a 3.4 mm diameter post, a short tapered neck and a 4 mm diameter ball on top. Total height is 7 mm. Overall height: 7 mm Post diameter: 3.4 mm Ball diameter: 4 mm Neck: tapers from 3.4 mm to 2.4 mm over 0.6 mm Flat base, prints upright without supports