iPhone 15 Pro Bike Mount 31.8mm Bar
Created today
Description
Handlebar phone mount sized for the iPhone 15 Pro (146.6 × 70.6 × 8.25 mm). A back plate with a weight-saving window holds the phone, four L-shaped corner clips wrap the edges and hook 4 mm over the screen face, and a split clamp on the back fits 31.8 mm handlebars.
The clamp split is present, but no bolt tab or hardware mounting is included yet. A strap or added bolt tab is needed to tighten it on the bar.
Specifications
- Phone: iPhone 15 Pro, 146.6 mm tall, 70.6 mm wide, 8.25 mm thick
- Pocket: 71.2 × 147.2 mm inside (0.6 mm total clearance)
- Corner clips: 4, each with 18 mm arms along both edges, 2.4 mm wall, 4 mm lip over the face
- Back plate: 3 mm thick, 6 mm corner radius, central cutout to reduce weight
- Clamp: 31.8 mm bore, 4 mm wall, 50 mm wide, split at the bottom
- Overall size: 76 × 152 mm footprint, about 54 mm tall in the print orientation
- Print notes: supports needed under the back plate in the modelled orientation; PETG or ASA suggested for heat and vibration
- Parts: back plate, corner clips, handlebar clamp (single welded body)
Images
More like this
Explore more in Automotive, RC & Hobby →
Kawasaki z1100 bar end mirror handle bar adaptors
A threaded adapter that steps an M18x1 fine-pitch external thread down to an M6x1 internal thread, made for fitting bar end mirrors to the handlebars of a Kawasaki Z1100. The stud is 16 mm tall with no flange, and a 10 mm hex socket in the base lets it be driven in with an Allen key. Remix hooks Hex socket size and depth: 10 mm across flats, 5 mm deep. A deeper socket (7 mm was the earlier value) grips a key better but leaves less solid material around the M6 thread. Change the across-flats value to match a different key. Overall height: 16 mm. Taller gives the mirror stem more thread to bite into; shorter reduces how far it protrudes from the bar end. Thread fit: both threads are modelled at nominal size. FDM usually needs 0.1–0.2 mm of adjustment on the M18x1 outside and the M6x1 inside, so print a short test ring first. Add a stop: there is no flange, so insertion depth is set by feel. A thin collar or a shoulder on the mating part would give a hard stop. Pairs with: a lock nut or thread-locking compound on the M6 side to keep a mirror from backing out under vibration. Starting dimensions External thread: M18, 1 mm pitch Internal thread: M6, 1 mm pitch, through the full height Height: 16 mm Socket: 10 mm hex, 5 mm deep Check the thread on your actual bar ends before relying on it. Print in a tough material such as PETG or ABS, since the part sees vibration and weather.
Saipa Pride 111 Clock Bezel Phone Cradle
Preliminary replacement for the Saipa Pride 111 (2011 / 1390) dashboard clock bezel, with a landscape cradle for the Samsung Galaxy A54 5G. All bezel dimensions are placeholders and not taken from the car. Fit status Host: Saipa Pride 111 clock opening. Bezel size, spigot depth and clip positions are placeholders. Phone: Galaxy A54 5G, 158.2 × 76.7 × 8.2 mm, plus 3 mm case allowance and 1 mm clearance per side. Does not fit other Pride trims or other phones. Measure before printing Dash opening width, height, depth, corner radius and clip or screw positions. Notes The cradle is wider than the clock opening, so it projects forward of the dash. Open-top slide-in loading, side lips, a bottom ledge and a USB-C side slot. Tilt is 15° back. Check it against the dash and your sight line. Print in ASA or PC-CF. PETG softens in a hot parked car.
86x45mm Ovaler Karosserie-Blindstopfen mit Snap-Fit-Clips
Geschlossene ovale Abdeckplatte für eine 80 × 39 mm große Öffnung in etwa 1 mm dickem Karosserieblech. Die Kontur ist ein Stadion-Oval, also ein gerades Mittelstück mit vollständig runden Enden. Die Platte wird eingedrückt, die integrierten Snap-Fit-Clips federn zurück und rasten hinter dem Blech ein – ohne Schrauben, Kleber oder separate Befestigungsteile. Die Abdeckung lässt sich wieder entfernen, ohne das Blech zu beschädigen. Das Teil wird als ein Stück gedruckt. Frontplatte: 86 × 45 mm, 2 mm dick, vollständig geschlossen, gerundete Kanten; die 2 mm fallen an der gerundeten Kante etwas dünner aus Einsatz: Außenkante 80 × 39 mm, Endradius 19,5 mm, 4 mm tief, hohle Wand mit 1,6 mm Stärke Innenöffnung: 76,8 × 35,8 mm Flansch: rundum 3 mm breit, an den Längsseiten wie an den Enden; die Clip-Haken liegen vollständig innerhalb der Plattenfläche Clips: zwei Zungen an den Längsseiten oben und unten, je ein 0,7 mm hoher Haken mit Rampen-Anlauf und flacher Fangfläche für 1 mm Blech Clip-Schlitze: 1 mm breit × 6 mm lang durch die Wand der Längsseiten, geben den Zungen Platz zum Federn Passung: Die Außenkante des Einsatzes entspricht exakt 80 × 39 mm, es bleibt kein Spiel – straffer Sitz, vor dem Einbau einen Probedruck einplanen Einbauraum: Die Frontplatte misst 86 × 45 mm; vor dem Einbau prüfen, ob um die Öffnung herum genug Platz für 45 mm Höhe ist Material: PETG oder ASA, mit der Frontseite nach unten drucken Bauteilmaße auf der Druckplatte: 86 × 45 × 6 mm
Drone Frame For 8mm Motors
A quad frame for 8 mm motors with a 14 mm wide, lattice-cut camera mount on the top deck. Fitment Motors: 8 mm, in 8.4 mm bore cups. Does not fit 7 mm or 11xx motors without resizing. Camera mount: 14 mm wide extender and slanted plate, with a single vertical wall at the low end and a 7 mm lens hole. Frame: 4 arms, 58 mm guard rings with two curved sticks each, raised deck, hollow pointed legs. Check before printing Measure the camera body width. The 14 mm wall suits only nano-size FPV cameras. Known limits No flight-controller holes in the deck. The camera has no retaining feature. Use a strap or glue.
Oo scale buildings half relief roof with ridge tiles
Two tiled OO-scale roof slopes, two slated roof slopes, five brick chimneys and a downpipe, all laid out to fit a 256 × 256 mm bed in one plate. Remix hooks Layout: the four roofs sit side by side along X, with chimneys and the downpipe in the strip on the right. The whole set spans about 240 × 156 mm. Tiled roofs: 46 × 156 mm slab, 3 mm thick, 4.5 mm radius ridge tile wrapping 135°, half-round gutter with 2 mm opening and 0.8 mm walls, closed ends and a 2 mm outflow hole. Slated roofs: 46 × 130 mm, 30° pitch, 2.5 mm courses, 7 mm slates, no gutter. Chimneys: 7 × 7 mm, 16 mm tall, base cut at 30°, printed upside down. Change the height or the cut angle for other roofs. Downpipe: 2 mm × 110 mm solid rod. Lengthen it or add brackets. Pairs well with a printed wall or building shell that matches the 30° and 45° pitches.
square hitch
Pare-chocs avant 141 mm pour MN82 LC79 à l'échelle 1/12, avec un bull bar pleine largeur et des cages de protection devant les phares principaux. Largeur du pare-chocs : 141 mm, profondeur 14 mm, hauteur 16 mm (estimées) Bull bar : montants à ±40 mm et ±65 mm, traverse haute à 37 mm, traverse basse Cages de phares à ±55 mm, 16 mm de large et 14 mm de haut Ouvertures d'antibrouillard et creux central conservés, sans grilles Matériau conseillé : PETG ou nylon