Volvo XC60 2009-2017 Armrest Storage - Front Doors
Created 3 months ago
Remixed once
Description
A hollow storage tray insert designed to slip into the factory grab handle cavity of a vehicle door panel. The primary body tapers downward with a slight asymmetric offset to clear internal door mechanisms, while a perimeter lip catches the edge of the armrest opening to suspend the tray in place.
- Top Profile: 135mm x 42mm (excluding lip)
- Depth: 58mm clearance
- Wall Thickness: 2mm standardized shell
- Fitment Note: Based on approximate baseline dimensions for mid-size SUV door handles. The retention lip extends 4mm outward to prevent the tray from falling into the door cavity.
Images
More like this
Explore more in Automotive, RC & Hobby →
Lego piece for wagon door runner with thinner teeth bit slightly smaller
Wagon door runner to replace 3 off 15208 bricks Version with slightly too large slope
0.355 to 0.370 Golf Ferrule
Custom transition ferrule designed to mate golf shafts with an adapting taper. Before printing, verify your shaft tip standard. This part spans from a 0.355-inch taper dimension to a 0.370-inch parallel dimension. Critical Measurements: Inner Bore (Bottom): 9.0 mm (0.355") Inner Bore (Top): 9.4 mm (0.370") Outer Diameter: 13.5 mm (0.530") constant Length: 22.0 mm (0.875") Does not fit standard parallel-only 0.370" shafts at the base without binding.
Custom 16T Mod 0.5 Gear
What it's for A custom 16-tooth spur gear designed for tight tolerances and specific meshing requirements. Built with a modified pressure angle for a sharper tooth profile, and zero standard clearance to strictly match the requested root and outer diameters. Dimensions Outer Diameter: 9.00 mm Root Diameter: 7.00 mm Bore Diameter: 1.55 mm Thickness: 2.00 mm Module: 0.5 (with 28° pressure angle) Print notes Given the small 1.55 mm bore and fine module 0.5 teeth, a resin printer or an FDM machine with a 0.2 mm nozzle and highly calibrated flow is recommended. If printing on standard 0.4 mm FDM, horizontal expansion (XY compensation) may be needed to keep the bore true to size.
D-Shaft to Hex Motor Adapter
A rigid drive adapter connecting a standard D-shaft motor to a hexagonal RC wheel hub. The base features a keyed socket to prevent slip under torque, while the driven end seats into the tire's existing recess. Overall Length: 25 mm Motor Socket: 6 mm diameter with a 3 mm flat profile, 10 mm depth Wheel Drive: 5.2 mm flat-to-flat hexagonal peg, 10 mm length Base Diameter: 12 mm for structural wall thickness around the socket
5mm Hex to D-Shaft Adapter
Adapter coupler designed to bridge a D-shaft DC motor and a hex-hub wheel. Built to a total length of 30mm, featuring a dedicated socket for the motor shaft and a hexagonal drive peg for the wheel. Motor Socket: Sized for a D-shaft with a 3mm flat (assumes a standard 4mm overall shaft diameter). Depth allows for a 10mm long shaft. Wheel Drive: Hexagonal peg scaled to 4.8mm across flats to provide sliding clearance into a rigid 5mm hub. Clearances: Includes 0.2mm offsets on all critical mating surfaces for standard FDM printing tolerances.
Snap-Fit Poultry Band
A heavy-duty, flex-to-fit poultry leg band designed for easy application on turkeys. Customizing the Fit Band Diameter: Currently scaled for roughly a 1-inch (25.4mm) leg, making it suitable for mature turkeys. Band Width: The height along the leg is half an inch (12.7mm). The Hinge: The back of the ring thins out to 1mm to create a living hinge. You can thicken this if your material is exceptionally soft, or thin it further if you are using a stiffer PLA. The Lock: Features a horizontal bulb snap-fit. The locking pin squeezes through the entry gap and clicks into an enclosed cavity, keeping it secure even during movement. Adjust the bulb diameter or cavity clearance depending on your printer's tolerance.