Wazowski — Hinged Arms, Viper Horns
Created today
Description
Wazowski is a set of two hinged monster arms and two horns, made to sew onto a maternity shirt panel. Each arm splits into an upper arm and a forearm with hand, and the horns are slender, backward-curving thorns in the style of a desert horned viper.
Features
- Upper arm with a single lower hinge plate. The top plate is left off so the forearm can be glued in place.
- Forearm and hand with three fingers and a thumb, plus a short pin that locates in the hinge hole.
- Two horns, 60 mm tall, tapering to a fine tip with a slight curve.
- Round flanges with six sewing holes on each arm and horn.
Print notes
- Print the arms in TPU or another flexible filament so they move with fabric.
- Glue the forearm knuckle onto the hinge plate with the pin seated in the hole.
- Proportions are set for scaling, so resize in the slicer to fit.
Images
More like this
Explore more in Gifts, Seasonal & Personalized →
Yoshi Saddle Shell Backpack Mount
A red Yoshi-style shell dome on a white base plate that straps onto a backpack. What it's for Turns a backpack into a Yoshi costume piece. Webbing passes through four slots in the base plate, so the shell sits on the backpack's outer face. Dimensions Overall: about 214 × 175 × 94 mm, fits a 256 mm bed in one piece Dome wall: about 4 mm, hollow underneath Base plate: 6 mm thick Strap slots: four, each 44 × 7 mm, at X ±60, Y ±32 Remix ideas Add white spots or a ridge band on the dome Widen the slots for thicker webbing Add a foam pad under the base plate
Curved Halloween Horn for "Power"
A hollow, gently curved cone horn with an open base, sized for Halloween costumes. Base diameter is 40 mm, height 60 mm, with the tip leaning 25 mm to one side and a 2.5 mm wall. Remix hooks Base diameter (D = 40 mm): widen for a headband mount, narrow for a hairclip or small hat. Bend (25 mm): lower for a straighter horn; higher gives a hook-like sweep, but needs more support when printed upright. Wall (2.5 mm): thin it to save filament, thicken for durability. Height (60 mm): stretch for a taller, more dramatic horn. Pairs with A mirrored copy for a matching left and right set. A headband, a hat, or a printed base ring with a slot for mounting.
Starfleet Communicator Halloween Prop
A handheld communicator prop in the spirit of classic Star Trek, sized to carry or clip to a costume belt. It is a 90 × 36 × 12 mm slab with rounded corners, a slotted speaker grille, a round dial and a raised gold-style delta emblem. Remix hooks Body size: 90 × 36 × 12 mm. Scale length for a chunkier prop or shrink it for a pocket version. Grille slots: nine slots at 4 mm spacing. Change the count or width for a different look. Emblem: the delta is a simple 4-point polygon. Swap in a different insignia or text. Dial: 10 mm round knob. Make it a button, or add a hole for a small LED. Pairs with: a belt clip, a keyring loop on the back, or a hinged lid to make it a true flip communicator. Printing: print the parts in silver, gold and blue, or paint after printing.
X26 Prop Holster, 2.21 in Belt, Strap
A prop X26 holster pouch with a belt loop and a separate U-shaped retention strap, sized for a duty belt 2.21 in (56 mm) tall and 0.21 in (5.3 mm) thick. Fit notes Belt slot: 60 mm tall, 7.5 mm thick. It will not fit belts wider than about 58 mm. Pocket: tapers from 70 × 44 mm at the base to 84 × 48 mm at the mouth, 130 mm deep. These are estimated prop dimensions, not measured. Check your prop before printing. Strap: a separate U-shaped piece with keyholes that mate with the two 5 mm studs on the rim. It prints flat and is not attached to the pouch. Not a working Taser holster. Prop use only.
Elderstab 1.0
What it's for A two-piece print of the iconic Elder Wand, split cleverly right after the third handle knob to hide the seam. Dimensions Total length: ~250 mm Handle: ~102 mm, featuring a 10.4 mm x 3.2 mm recess for a ring magnet and a 35 mm deep secret compartment (6.5 mm diameter) hidden behind it. Tip: ~150 mm, with a 10.4 mm x 3.8 mm recess for a flat magnet (includes extra depth for felt padding). Assembly Glue a 10x3 mm ring magnet into the handle and a 10x2 mm flat magnet into the tip. Add a thin piece of felt between them for a softer snap. The secret compartment can hold a tightly rolled message.
150mm Bayonet Twist Vault
A 150mm mechanical drop-in vault, built around a 50mm twist-lift track. This replaces the friction fit of the original 150mm Borg Friendship Vault with a proper bayonet mechanism. The outer cage runs three 18mm tall helical tracks to guide the core. The top cap terminates in a 40mm hexagonal drive plug; dropping it onto the core and twisting counter-clockwise forces the payload to lift 50mm out of the chassis. Bore Clearance: The 98mm core runs inside a 102mm cage bore. Verify your machine holds tolerances on large cylinders. Support-Free: The massive 90mm flat bridges of the original have been replaced by mechanical vertical slots with 45-degree angled roofs. No supports needed for the cage or core lugs. Payload Capacity: The hollow inner void measures 76mm in diameter by 110mm deep. To assemble, line up the core lugs with the vertical entry slots on the inner walls of the cage, push down to the top stop, and twist right to lock it securely to the bottom.