Wide-Stance Filament Bracket Set
Created yesterday
Description
A sturdy, flat-packed filament spool holder with an open frame base and dual arching uprights.
Designed for standard 16mm rods or dowels, this is laid out flat for maximum printing strength along the layer lines.
Remix Hooks
- Rod Diameter: Currently tuned to 16.5mm to comfortably clear 16mm rods.
- Upright Spacing: The upright arches span 150mm between the 80mm and 60mm heights.
- Hardware: Sized for 9mm diameter screw heads to sink flush into the 10mm thick base, clamping down into the uprights.
Images
More like this
Explore more in Workshop & Tools →
Hilti Nuron Battery Mount
A wall-mounted receiver bracket for Hilti Nuron batteries. Heavy battery packs love to lever short brackets right out of the drywall. This bracket gives them a solid vertical footprint to spread that load, catching the battery's sliding interface on an internal U-channel with a dead stop at the base. Internal Channel: 63mm wide (48mm opening) Clearance: Counter-sunk screw holes keep the hardware below the sliding surface Detail: Features a debossed HILTI logo on the backplate that stays clear of the sliding path
Hilti Nuron Battery Bracket v3
What it's for A heavy-duty, wall-mounted slide bracket engineered specifically for Hilti Nuron battery packs. Designed to mount vertically, it features precision-cut clearance channels and flared 45-degree entry ramps for blind sliding, backed by a solid stop block to prevent bottoming out. Four reinforced, deep-countersunk screw channels ensure the mount stays locked to the wall regardless of the battery weight. Dimensions Overall footprint: 107 mm length × ~93 mm width × 23.5 mm depth. Internal track: 61.5 mm outer track width, 51.5 mm inner neck clearance. Mounting: 4× countersunk screw holes (5.5 mm shaft, 13.5 mm head, 5 mm deep sink). Print notes Recommend rigid, high-strength materials like PETG or ABS to handle the repeated friction and weight of the Nuron packs. Print face up with the flat back resting completely against the bed. Clearances are set to exact measurements, so a well-tuned printer is necessary to keep the slide rails from binding.
no clip Hilti nuron v3
Screws mounted inside the track usually mean the battery casing drags across the screw heads if they don't sit perfectly flush. Moving the mounting holes to the solid outer flanges gets the hardware entirely out of the sliding path and stops the bracket from rocking when you yank a heavy pack out. Width: Pushed out to 94mm to give the screws enough meat to bite into. Clearance: 15mm deep counterbores hide the screw heads in the outer body, leaving a solid 5mm base to clamp against the wall.
Attila Custom Wall Brush
A classic flat wall brush profile, completely customizable for your shop or prop box. It prints as a solid piece, designed to be dropped flat on its back in the slicer so the text and profile print cleanly without supports. Remix Hooks The Text: Currently running a 1.25mm deboss. If you change the font, watch the spacing and depth. The Handle: Sized at 35x14mm with a heavy 6.5mm round-over for comfort. You can scale the Z-height for a longer beaver-tail handle. The Ferrule: Features triple 1.2mm crimp grooves for that authentic hardware-store look.
small Bottle Syringe Clip
A custom-sized double ring designed to couple a 14.5 mm syringe to a 31 mm bottle neck. Syringe bore: 14.5 mm with an 8 mm front insertion slot Bottle bore: 31 mm (snaps on via a 22 mm back slot) Clearance: 4 mm bridge spacing The branding is now recessed 0.6 mm directly into the bottle ring's inner wall, keeping the outer profile completely flush. Check your syringe outer barrel measurement before running this.
Biofloc Monitor Station Enclosure
An enclosure is only as good as the snarl of wires it prevents. This is a heavy-duty two-part monitor housing built specifically for FDM printing, designed to group, separate, and anchor a complete suite of biofloc water-quality electronics without turning into a bird's nest inside. The layout isolates the battery compartment at the bottom and keeps the DC buck converters and relay in a ventilated top section, leaving the central deck clear for the ESP32 and an array of sensor interfaces. Internal divider walls double as cable routing channels, forcing the wiring to stay orderly. Core Features Printability: Both halves print completely flat on the build plate (Z=0). The integrated bottom handle is flush with the front face to avoid overhangs. Dimensions: 170 mm width × 250 mm height × 75 mm depth. Hardware Required: 6× M3 screws for the rear cover; additional M3 hardware for the internal standoffs and the 16x2 LCD faceplate mount. Ports: Bottom panel holds 4× sensor ports (3× 8mm, 1× 6mm) with engraved labels. Right panel holds cutouts for 12V DC, an SD card slot, a rocker switch, and USB programming access.