X26 Prop Holster, 2.21 in Belt, Strap
Created today
Description
A prop X26 holster pouch with a belt loop and a separate U-shaped retention strap, sized for a duty belt 2.21 in (56 mm) tall and 0.21 in (5.3 mm) thick.
Fit notes
- Belt slot: 60 mm tall, 7.5 mm thick. It will not fit belts wider than about 58 mm.
- Pocket: tapers from 70 × 44 mm at the base to 84 × 48 mm at the mouth, 130 mm deep. These are estimated prop dimensions, not measured. Check your prop before printing.
- Strap: a separate U-shaped piece with keyholes that mate with the two 5 mm studs on the rim. It prints flat and is not attached to the pouch.
- Not a working Taser holster. Prop use only.
Images
More like this
Explore more in Gifts, Seasonal & Personalized →
Starfleet Communicator Halloween Prop
A handheld communicator prop in the spirit of classic Star Trek, sized to carry or clip to a costume belt. It is a 90 × 36 × 12 mm slab with rounded corners, a slotted speaker grille, a round dial and a raised gold-style delta emblem. Remix hooks Body size: 90 × 36 × 12 mm. Scale length for a chunkier prop or shrink it for a pocket version. Grille slots: nine slots at 4 mm spacing. Change the count or width for a different look. Emblem: the delta is a simple 4-point polygon. Swap in a different insignia or text. Dial: 10 mm round knob. Make it a button, or add a hole for a small LED. Pairs with: a belt clip, a keyring loop on the back, or a hinged lid to make it a true flip communicator. Printing: print the parts in silver, gold and blue, or paint after printing.
Grab Pack Prop Set
What it's for A wearable grab pack costume prop designed for a 9-year-old. Includes the main backpack unit with integrated strap loops, plus two separate grabber arms ending in wide, open-palmed four-finger hands. Dimensions Backpack: 250 mm total width across the outer spools, designed to sit flat against the wearer's back. Strap loops: 35 mm internal clearance, sized to easily accept standard 1.5-inch webbing. Hands: Approximately 120 mm across the splayed fingers, giving a large cartoonish footprint. Print notes The backpack body prints as a single solid piece with the spools attached. The launcher arms and hands are separate bodies designed to print completely flat on the bed for maximum strength and zero supports. Paint them up or string actual colored wire between the backpack spools and the arm hubs to complete the rig.
Luggage Strap Tag, 5 mm Slot, STEVE
A 90 × 50 × 3 mm luggage tag with a 5 × 22 mm strap slot and the name STEVE raised inside a recessed label panel. Fitment Fits straps up to 5 mm thick through the 22 mm-wide slot. Does not fit wide or double-layer straps, or standard key rings without a loop. Measure the strap thickness before printing; the slot is 5 mm. The lettering stands 0.9 mm proud of the panel floor and sits below the tag's top surface, so it is protected from rubbing.
Curved Halloween Horn for "Power"
A hollow, gently curved cone horn with an open base, sized for Halloween costumes. Base diameter is 40 mm, height 60 mm, with the tip leaning 25 mm to one side and a 2.5 mm wall. Remix hooks Base diameter (D = 40 mm): widen for a headband mount, narrow for a hairclip or small hat. Bend (25 mm): lower for a straighter horn; higher gives a hook-like sweep, but needs more support when printed upright. Wall (2.5 mm): thin it to save filament, thicken for durability. Height (60 mm): stretch for a taller, more dramatic horn. Pairs with A mirrored copy for a matching left and right set. A headband, a hat, or a printed base ring with a slot for mounting.
Elderstab 1.0
What it's for A two-piece print of the iconic Elder Wand, split cleverly right after the third handle knob to hide the seam. Dimensions Total length: ~250 mm Handle: ~102 mm, featuring a 10.4 mm x 3.2 mm recess for a ring magnet and a 35 mm deep secret compartment (6.5 mm diameter) hidden behind it. Tip: ~150 mm, with a 10.4 mm x 3.8 mm recess for a flat magnet (includes extra depth for felt padding). Assembly Glue a 10x3 mm ring magnet into the handle and a 10x2 mm flat magnet into the tip. Add a thin piece of felt between them for a softer snap. The secret compartment can hold a tightly rolled message.
150mm Bayonet Twist Vault
A 150mm mechanical drop-in vault, built around a 50mm twist-lift track. This replaces the friction fit of the original 150mm Borg Friendship Vault with a proper bayonet mechanism. The outer cage runs three 18mm tall helical tracks to guide the core. The top cap terminates in a 40mm hexagonal drive plug; dropping it onto the core and twisting counter-clockwise forces the payload to lift 50mm out of the chassis. Bore Clearance: The 98mm core runs inside a 102mm cage bore. Verify your machine holds tolerances on large cylinders. Support-Free: The massive 90mm flat bridges of the original have been replaced by mechanical vertical slots with 45-degree angled roofs. No supports needed for the cage or core lugs. Payload Capacity: The hollow inner void measures 76mm in diameter by 110mm deep. To assemble, line up the core lugs with the vertical entry slots on the inner walls of the cage, push down to the top stop, and twist right to lock it securely to the bottom.