Made by HelixRhino
Created 1 months ago
Description
A 70x25 mm solid front wheel designed to mate with a standard 12 mm RC hex drive. Built as a single rugged piece, it combines a deep-block tire tread with a solid structural hub to handle the weight of larger FDM parade and display builds.
Images
A single-arm servo horn for the SG90 micro servo, with a 3.2 mm linkage hole 12 mm from the output shaft centre. Fitment Fits: SG90 and compatible 9 g servos with the 21-tooth, ~4.8 mm output spline. Does not fit: MG90S metal-gear servos with a different spline count, or 25T servos such as MG995/MG996. Arm: 12 mm centre distance, 4 mm thick, rounded edges. Check before printing Test the spline bore on a scrap print. Bore size is ~4.9 mm with small tooth notches, and printer tolerance varies. Adjust it if the fit is loose or tight. The part prints flat with no supports, and PLA works.
What it's for 30×40 mm 底板,前端带两片独立固定耳片,用于锁 SG90 舵机自带的安装耳。 Dimensions 底板 30×40×2 mm,圆角 R1,2 个 φ2 孔,孔距 22 mm 耳片各宽 4.2 mm、厚 2 mm、高 14.5 mm 耳孔 φ2,中心距 28 mm,孔内侧距耳片内边 0.2 mm Remix ideas 加宽耳片内侧以增加强度 恢复 U 型侧壁
ServoLink is a compact single-bar crank arm for SG90 micro servos. One end carries a 21-tooth spline socket that grips the servo output shaft. The other end has a 3.2 mm round hole for a linkage pin or screw. The part is flat and printable without supports. Dimensions Hole centre to centre: 12 mm Thickness: 4 mm Left hole: SG90 spline, about 4.9 mm across the teeth Right hole: 3.2 mm diameter Hub: 9 mm round, arm end: 7 mm round, with softened edges Print notes PLA, printed flat, no supports The spline is sized close to nominal. Scale the hole slightly if your printer runs tight or loose.
Gancho de garrafa de treino em J, 200 mm, com braçadeira bipartida na base: corpo fixo ligado à haste e tampa separada que fecha por encaixe de pressão ao redor da alça de 12 × 24 mm. Pontos de remix Snap-fit: ganchos flexíveis de 8 mm de comprimento, 1,8 mm de espessura e ressalto de 0,6 mm (armlen, armt, ridge). Entrada em rampa, retenção reta. Folga: 0,2 mm entre tampa e corpo (gap). Trava extra: furo M3 em gota atravessando tampa e corpo, com porca sextavada embutida no lado +X. Paredes: wallx (6,4 mm) e wallf (7,5 mm) definem o tamanho externo; reduza se o furo M3 for dispensado. Haste e gancho: inalterados, seção 10 × 14 mm, bojo de 40 mm, boca de 34 mm. Combina com: parafuso M3 e porca M3 (opcionais); imprima corpo e tampa separados em PETG ou PLA.
A stroller ski for snow: a runner that takes the place of a stroller wheel, with the wheel held between two upright walls. The ski is 280 mm long end to end and 80 mm wide, flat at the tail, with a front tip that sweeps up through a tight 100 mm radius over 50° and rises to about 39 mm above the plate. Seen from above, the front narrows from the full 80 mm width to a point, giving it the spear-shaped profile of a classic ski. The wheel holder is 71 mm wide, 120 mm long and 49 mm tall — two flat upright walls with 55 mm clear between them, tied together by cross ribs at the front and back. Two strap slots run straight through both walls, one 20 mm above the other. Both are 30 mm along the ski and 5 mm tall; the lower starts 5 mm above the ski surface and the upper at 25 mm, so a flat strap up to about 30 mm wide can pass through and wrap under the wheel. The 55 mm wall gap is the constraint; almost everything else is a choice. The walls are straight, so a 220 mm wheel sits uncradled between them — the curved seat matched to that diameter is the obvious next version. Remix hooks Ski footprint: 280 × 80 mm is a starting value, not a rule. Longer and wider spreads load in deep snow; shorter turns tighter. Keep the holder centred over the wheel position and the rest is free. Tip taper: the point is currently gradual, starting well back from the tip. Lengthening the taper softens the look and keeps strength in the tip; shortening it sharpens the spear but weakens the point and makes it dig in — worth changing one step at a time. Tip radius: 100 mm through 50°. A smaller radius kicks sharper and higher for soft snow; a larger one rolls flatter on packed surfaces. Mirror it onto the tail for a reversible ski. Wall gap: 55 mm clear between the walls is the hard constraint — change it only for a different wheel or hub width. Strap slots: two slots at 30 × 5 mm, set 20 mm apart, with the lower 5 mm above the ski surface. Resize them to the strap on hand; the spacing is free if the strap should take a different path under the wheel. Wheel seat: straight walls mean no cradle. A curved seat matched to the 220 mm wheel is the obvious variant, and the flat inner wall face is a clean place to start it. Pairs with: a stroller wheel position and a flat strap; print a second, mirrored ski to convert both wheels.
A 1/10-scale ladder-frame chassis for a rear-wheel-drive RC hot rod truck. The frame is 340 mm long with 95 mm rail spacing and a 260 mm wheelbase, and it includes a front servo plate, motor plate, battery tray with cutouts, rear diff block, six body-mount posts, and placeholder axles and wheels. The dimensions are a starting point rather than a scale copy of a full-size Factory Five 1935 truck, and the mounts and axles are not sized to a specific motor, diff, servo, battery or drivetrain. Check hardware fit before printing. The frame length exceeds many printer beds, so plan for a large-format printer or split the frame into sections. Frame: 340 mm long, 95 mm rail spacing, 260 mm wheelbase Includes: five crossmembers, front servo plate, motor plate, battery tray with cutouts, rear diff block, six body-mount posts Placeholder parts: axles and wheels, not matched to a specific drivetrain Printing note: 340 mm frame length may require a large bed or sectional printing