Description
这是一只杯形小罩:外壁为圆筒,内腔中空,内腔中心立有一根细立柱,底部另向下伸出一根带缝的柱。整体外径16.5毫米,含底部立柱的总高16毫米;杯体高9毫米,内腔深7毫米,中心立柱直径2.5毫米、高6.5毫米,柱顶低于杯口0.5毫米,套在轴或销上时不会凸出。底部立柱总高7毫米,最下一段直径7.5毫米、高2.5毫米并带倒角,向上收为直径6毫米的柱身,中间开有1.4毫米宽的缝隙,可借助弹性夹紧或让位。适合做端盖、保护套、限位垫或小型配合件,按实际轴径核对内腔尺寸后使用。
Images
Hideaway ist eine kleine, oben offene Box mit Haken, die über einen Türrahmen gehängt wird und eine Batteriebox für Lichterketten verdeckt. Der Haken sitzt an der Rückseite, der Kabelausschnitt wandert seitlich aus der Box, damit die Vorderwand geschlossen bleibt. Maße Innenraum: 62 × 30 × 24 mm (passend für eine 3×AA-Batteriebox) Haken: für Türrahmen von ca. 20 mm Dicke, 40 mm breit Wandstärke: 2,4 mm Kabelausschnitt: 8 × 8 mm in der rechten Seitenwand, knapp über dem Boden Hinweise Ein Teil, kein Deckel – oben offen Vorderwand geschlossen, Kabelauslass seitlich Ohne Stützen druckbar, Rückseite flach auf das Druckbett
Replacement two-way joiner for the top-front-center of a fiberglass-rod printer enclosure. It splices two nominal 8.2 mm rods end-to-end and carries a flat-lying arm with a screw boss for a Sercomm RC8110 camera. Print it as one piece with the arm flat on the bed, then rotate the part about the rod axis during installation to aim the camera downward and toward the bed center. Specifications Rod sockets: 8.35 mm ID, 30 mm deep per side, 0.5 mm entry chamfers, separated by a 3 mm solid center stop; 63 mm overall sleeve length. Sleeve: approximately 14.35 mm OD with 3.0 mm wall thickness. Arm: 20 mm wide and 6 mm thick, extending 50 mm from the sleeve, with a root block and gusset blending it into the sleeve. Camera boss: 28 mm diameter and 6 mm thick, with a 6.6 mm through-hole and a 12 mm × 2 mm counterbore for a 1/4"-20 camera screw. Print footprint: 63 × 71.2 × 14.4 mm as oriented on the plate; the teardrop socket bores and flat arm are intended to print without support. Fit: press-fit for measured 8.19–8.20 mm rods; PETG wall thickness is sized to resist splitting and bending from the tensioned enclosure fabric.
A screw-on lid in the spirit of a big jar cap, sized to seal the wall bracket that takes a 6 inch portable AC hose. The inside carries a female thread that mates with the bracket's 145 mm male thread, so it twists on the same way the hose does. Design notes 12 mm pitch, 5 mm thread depth, 2.5 mm clearance over the 145 mm thread 155 mm outer diameter with a 3 mm closed top and thin walls to save print time Scalloped grip notches around the rim Prints open-side up or top-down; the thread is coarse, so a 0.4 mm nozzle is fine
StrapSlot is a rectangular slot ring made for velcro straps — a buckle ring, strap keeper, or loop in one compact part. The internal opening is a clean 20 × 6 mm slot, and the 4.7 mm body uses 4.5 mm walls with rounded corners for a tidy outer profile. A 1 mm chamfer on the outer top and bottom edges softens the outside of the ring, while the slot edges stay square. Use it to keep a strap flat and contained, or as a replacement ring where a rectangular slot is needed. Dimensions | Feature | Size | | --- | --- | | Ring (each) | 29 × 15 × 4.7 mm | | Internal slot | 20 × 6 mm | | Wall thickness | 4.5 mm | | Outer edge chamfer | 1 mm on top and bottom | | Slot edges | Square | | Corners | Rounded | | Full set footprint | 63 × 55 mm, 4.7 mm tall | In the set Six identical rings, arranged in a 2×3 grid with 5 mm gaps between them. The whole set sits flat on the plate at a single 4.7 mm height, so it prints as one batch. Snap or separate the rings after printing to use them individually. Fit notes The 20 × 6 mm slot is the critical fit dimension; check your strap width and thickness against it. The 4.7 mm overall thickness sets the ring depth. The 4.5 mm walls, rounded outer corners, and 1 mm outer-edge chamfer define the outside shape.
What it's for Flacher Türhaken, der über eine Tür greift. Ein geneigter Stift ersetzt die vordere Wand am unteren Haken. Dimensions Höhe (Z): 10 mm Wandstärke: 1,75 mm Obere Öffnung: 14,2 mm Obere Lippe: 4 mm tief Stift: Ø 2,5 mm, 5,5 mm lang, 40° zur senkrechten Wand geneigt Remix ideas Stift länger oder kürzer für andere Lasten Öffnung an andere Türstärken anpassen Dickere Wand für mehr Tragkraft

A door-top hook sign for hanging over a door top or peg: a 95 × 160 × 5 mm plate with a one-piece flat hook on its top edge. The hook is a ring with a gap on its lower right, about 68 × 69.4 mm overall and 5 mm thick, reaching roughly 68 mm above the plate. Its ring wall is about 10 mm thick; the opening is fixed and does not adjust. Below the hook is an octagonal STOP sign with white lettering, then the message in dark raised text: six lines at one 6 mm size in a bold condensed face, with a blank line after “No Politics”: No Soliciting No Religion No Politics Ignoring this guarantees we will not use or purchase your product/service. It replaces a paper or card door hanger of similar footprint — nothing to laminate and nothing to tape up. Fits A door top or peg that clears the hook’s fixed opening — measure the opening against the actual door top or peg before printing, as nothing on the part takes up slack. A print bed at least 160 × 95 mm, since the plate prints flat. A one-piece print: plate, text, STOP sign and hook print together; no separate loop, screws, nuts or fasteners. Check before printing Measure the hook opening against your door top or peg. The ring wall is about 10 mm thick and the opening is fixed. Print the plate flat so the layers run along the hook. At roughly 68 mm of reach in a 5 mm section, the hook is a long cantilever; printing it stood on edge risks snapping it. Change filament at the layers where the red, white and dark areas begin if you want clean colour separation. Line spacing is about 9.2 mm pitch. The last line of text sits about 4 mm from the plate’s lower edge, so preview the layout and margin before committing to a long print. Known limits One hook thickness only, 5 mm — there is no heavier version. No through-slot for a knob or handle, and no screw-on loop or M3 hardware. The sign does not clamp or lock to the door; it hangs from the hook and lifts off. The hook opening is fixed; it does not adjust for different door tops or pegs.