5mm Round Head Pin
Created today
Description
A plain round-headed hardware blank, sized to match standard 5mm metric fasteners but stripped of threads and drive features.
Modification Points
- Dimensions: 5mm shaft diameter, 32mm shaft length (35mm overall).
- Tolerances: Prints exactly at 5mm. Scale the shaft down slightly (or drill your target hole) if you need a slip fit.
- Derivatives: Easy to modify into a clevis pin by adding a cross-hole near the tip, or cut a slot across the top to return it to a flathead.
Images
More like this
Explore more in Workshop & Tools →
60mm OD Flanged 45° Pipe
60mm outer diameter flanged pipe with a 45-degree elbow. Features a continuous 56mm inner bore with a 2mm wall thickness. The 100mm OD flange is positioned exactly 30mm from the base and runs 3mm thick. Check your clamp or mating collar against the flange thickness and 100mm outer diameter. No mounting holes are drilled; this part is built for bonded or slip-fit assemblies where the 56mm internal passage must remain entirely unobstructed.
Matix Snap-Fit Test Frame
Un piccolo frammento della scatola principale, isolato e progettato per essere stampato velocemente. Serve per testare fisicamente l'inserimento e lo scatto del frutto BTicino Matix prima di impegnare ore nella stampa del pezzo completo. Orientamento fedele: Si stampa in verticale, in modo che le linee di livello (layer) e i ponti della fessura riproducano esattamente le condizioni della scatola finita. Fianchi rigidi: Il profilo a "C" impedisce alla parete di flettere quando premi l'interruttore. Risparmio: Pochi grammi di filamento per verificare le tolleranze di aggancio.
Verbindungsstück l60mm,d60mm
A straight, uniform hollow pipe designed for structural use or fluid routing. The bore is continuous and centered, producing a robust 2 mm wall suitable for standard FDM printing. Outer Diameter: 60 mm Inner Diameter: 56 mm Length: 60 mm Wall Thickness: 2 mm Orient vertically on the build plate to print without supports.
Robust 3-Way Irrigation Manifold
A heavy-duty 1-to-3 splitter manifold designed for 5 mm ID irrigation hose. It prints completely flat on its base without supports, using teardrop-shaped mounting bosses to bridge the overhangs. To meet the structural requirement of 4 solid perimeters on a 5.4 mm outer barb, the internal channel strictly inside the hose stems necks down to 2.6 mm. Inside the thick bosses and the main manifold body, the passages open up to 5 mm and 7 mm respectively to minimize flow restriction. Remix Hooks Barb Spacing & Count: Adjust the port_solid() module to add more barbs or change the spacing for stiffer tubing. Port Layout: Expand the main body length and loop the for(x = ...) call to add 4, 5, or 6 outlets. Mounting: The flat rectangular body leaves plenty of room to cut countersunk screw holes if you need to hard-mount it to a rail or planter box.
Gardena Garden shears stop buffer
There is a little buffer to not let the shears overcross. Dimensions Base Cylinder: 16.7 mm diameter, 4.2 mm height. Top Cylinder: 6.8 mm diameter, 5.8 mm height. Total Height: 10 mm. Remix ideas Add a through-hole along the Z-axis to convert it into a stepped bushing or washer. Apply a slight chamfer to the top edge if it needs to press-fit or slide into a tight receptacle smoothly.
Side-Pinned Click Lock 2 40-Quarter Dispenser
What it's for A fully mechanical, gravity-fed coin magazine tailored for standard U.S. quarters. It stores a full $10 roll vertically and dispenses exactly $1 (four quarters) per cycle into the palm of the hand. The mechanism relies on a two-stage sliding escapement, now utilizing a side-mounted limit pin to ensure the coin path remains entirely unobstructed during travel. Dimensions Overall Envelope (Dispenser): 34 × 56 × 75 mm (when closed) Slider Thickness: 7.2 mm Coin Bore: 25.2 mm (optimized for 24.26 mm quarters) Clearances Slider Play: 0.4 mm vertical clearance inside the track Pin Clearance: 0.3 mm on the locking pin diameter Cap Threads: 0.6 mm diametric clearance for smooth twisting Assembly The main body, slider, cap, and limit pin print separately without supports. Insert the slider into the main body track, align the side slot with the right-hand hole on the body, and push the limit pin flush into the side countersink to capture the mechanism. Remix ideas Threaded Cap: The top of the magazine tube features a coarse 4mm-pitch thread. Alter the tube height to make a shorter 20-coin version. Coin Bore: Tweak the internal offset diameter for other currencies or custom arcade tokens. Slider Thickness: Scaling the Z-dimension alters how many coins drop per pull.